Advertisement
Advertisement
Table of Contents
Related Manuals for Pride Victory 9
Summary of Contents for Pride Victory 9
- Page 1 VICTORY 9 VICTORY 10 Including models: Victory 9 and Victory 10...
- Page 2 Performing a prohibited action can cause personal injury and/ or equipment damage. On the product, this icon is represented as a black symbol with a red circle and red slash. © Pride Mobility Products Corp. 2010 Rev. A/January 2010/INFMANU3986...
-
Page 3: Table Of Contents
Table of Contents INTRODUCTION ....................... 4 Victory 9/10 Technical Troubleshooting Guide .................4 How to Use Pride Model Specific Technical Troubleshooting Guides ..........4 System Retest ..........................4 SECTION 1 - KEY INSERTED INTO KEY SWITCH AND TURNED ON - NO SIGNS OF POWER ....................... -
Page 4: Introduction
INTRODUCTION VICTORY 9/10 TECHNICAL TROUBLESHOOTING GUIDE This Victory 9/10 Technical Troubleshooting Guide covers diagnostic and repair scenarios for Victory 9 and 10 scooters. This guide is divided into three sections to address three troubleshooting scenarios: Section 1 —— Key Inserted Into Key Switch And Turned On - No Signs of Power Section 2 ——... - Page 5 Diagram 1. Victory 10 Troubleshooting Key (Victory 9 May Differ Slightly in Appearance) Victory 9/10 Technical Troubleshooting Guide www.pridemobility.com...
-
Page 6: Section 1 - Key Inserted Into Key Switch And Turned On - No Signs Of Power
0VDC, then recharge the batteries and retest the system. —— If your multimeter indicates more than 18VDC, then go to Figure 4. Victory 10 Seat and Rear Shroud Removal (Victory 9 May Differ Slightly in step 18. Appearance) 3. Remove the seat and rear shroud. See figure 4. - Page 7 —— If your multimeter indicates less than 1 ohm, then replace the controller power harness (3) and retest the system. —— If your multimeter indicates greater than 1 ohm, then replace the circuit breaker (4) and retest the system. Figure 10. Circuit Breaker (4) Victory 9/10 Technical Troubleshooting Guide www.pridemobility.com...
- Page 8 10a back into connector 7d and go to the next step. Figure 14. Connector 8a Figure 15. Connector 7d Figure 11. Victory 10 Main Shroud Removal (Victory 9 May Differ Slightly in Appearance) www.pridemobility.com Victory 9/10 Technical Troubleshooting Guide...
-
Page 9: Section 2 - Key Inserted Into Key Switch And Turned On - Powers On But The Scooter Will Not Drive
—— If your multimeter indicates less than 1 ohm, then go to the next step. 5. Remove the main shroud. See figure 11. 6. Remove the cover from the controller (8). See figure 12. 7. Unplug connector 6a from connector 8b. See diagram 3. Figure 19. Connector 12a Victory 9/10 Technical Troubleshooting Guide www.pridemobility.com... - Page 10 —— If your multimeter indicates an open, then replace the tiller harness (10) and retest the system. —— If your multimeter indicates less than 1 ohm, then plug connector 10a back into connector 7d and go to the next step. www.pridemobility.com Victory 9/10 Technical Troubleshooting Guide...
-
Page 11: Section 3 - Beep Code Diagnosis
SECTION 3 - BEEP CODE DIAGNOSIS The controller (8) performs periodic diagnostics on the electronics of the Victory 9 or 10 scooter. The controller (8) monitors components of the electrical system such as battery charge, electromagnetic brake resistance, throttle pot (15) operation, and speed pot (17) operation. -
Page 12: Beep Code #6 - Throttle Trip
(15) and retest the system. 2. Remove the front and rear tiller shrouds and the console assembly. See figure 16. www.pridemobility.com Victory 9/10 Technical Troubleshooting Guide... -
Page 13: Beep Code #7 - Throttle Trip
29. —— If your multimeter does not indicate about 4.7k ohms, then go to the next step. —— If your multimeter indicates about 4.7k ohms, then replace the controller (8) and retest the system. Victory 9/10 Technical Troubleshooting Guide www.pridemobility.com... - Page 14 —— If your multimeter indicates about 100k ohms, then replace the tiller harness (10) and retest the system. —— If your multimeter does not indicate about 100k ohms, then go to the next step. Figure 35. Connector 16a www.pridemobility.com Victory 9/10 Technical Troubleshooting Guide...
-
Page 15: Beep Code #8 - Motor Disconnected
2. Measure resistance across pin 1 and pin 2 on connector 19a. See figure 38. —— If your multimeter indicates about 0.5-1.5 ohms, then go to step 4. —— If your multimeter does not indicate about 0.5-1.5 ohms, then go to the next step. Victory 9/10 Technical Troubleshooting Guide www.pridemobility.com... -
Page 16: Beep Code #9 - Possible Controller Trip
—— If the beep code stops after shutting down and the scooter drives when powered up, then go to the next step. —— If the beep code persists, then replace the controller (8) and retest the system. www.pridemobility.com Victory 9/10 Technical Troubleshooting Guide... - Page 17 —— If the scooter can be pushed easily in freewheel mode with no resistance, then replace the motor (19). —— If the scooter cannot be pushed easily while in freewheel mode, then replace the transaxle (22). Figure 43. Removing the Brake (20) and Motor (18) Victory 9/10 Technical Troubleshooting Guide www.pridemobility.com...
- Page 18 Victory 9/10 Technical Troubleshooting Guide...
- Page 19 Diagram 2. Victory 10 3D Wiring Diagram...
- Page 20 VOLT METER ELEASMB5404- ELEMETR1017 S-DRIVE CONSOLE CONTROLLER SPEED SWITCH HEADLIGHT TILLER SWITCH HORN HORN SWTROCK1006 FUSE BUTTON BUTTON BLOCK THROTTLE CHARGER HORN PORT DWR9966H004 ELEASMB5676 CIRCUIT BREAKER TO BATTERY Diagram 3. Victory 10 2D Wiring Diagram...
- Page 21 Pride Mobility Products Corporation 182 Susquehanna Ave. Exeter, PA 18643 Contact Information Main Toll Free Number 800.800.8586 Local Phone Number 570.655.5574 Internet Address for Product Information www.pridemobility.com Internet Address for Service Information www.prideservice.com “Live Chat” available 8:30 am — 5:00 pm EST Toll Free Service Hotline 877.800.1248 (Dealers Only)