Bontrager Transmitr MicroRemote Manual

www.bontrager.com
PN 597194
Battery activation
1. Twist anticlockwise to open the 2. Pull out the battery activation
remote. Keep the top half tab.
assembled.
A note about pairing
Up to four ANT+ compatible lights can be paired to the Transmitr MicroRemote in a single pairing session.
Once in pairing mode, the remote will automatically search for each activated light, to pair one at a time, in
sequence. The pairing process is the same for all ANT+ compatible lights, regardless of whether it's a front
light or a rear light.
NOTE: All lights must be paired in the same continuous procedure. If you choose to add a light later, you
will need to pair each light again at that time.
Pairing
1. Before starting, place the remote and all lights within 15 cm (6 inches)
of each other.
NOTE: Move 4.5 metres (15 feet) from other ANT+ compatible lights to prevent accidental pairing.
2. For all lights you wish to pair, turn on each light then quickly turn it off again.
NOTE: After completing this step, do not press the power button on the light again until pairing is complete.
3. Press and hold the button on the remote for at least 15 seconds. Position your thumb on the remote
button so you can see the red light flash under the button. Release the button when the green/red light
begins to flash.
NOTES: Upon entering the pairing process, all previously stored pairing is removed.
If a light is accidentally paired, start the pairing process again.
4. While the remote searches for a light, the LED flashes red. When the remote finds a light, the LED will
change from a red flash to a green flash and the found light will turn on.
5. While the remote is still flashing green, single-press the button on the remote. The LED will begin flashing
red again to find another available light to confirm you have paired the correct light.
6. Repeat steps 4 and 5 for each light to pair.
7. To exit pairing, single-press the button while the remote is flashing red. If pairing to 4 lights, the remote
will exit pairing mode automatically after the fourth light is paired.
NOTE: Waiting at any time for 10 seconds will also end the pairing process automatically.
Bontrager
Transmitr MicroRemote
3. Twist the remote clockwise to
close.
About this product
A small ANT+ and Bluetooth wireless remote that's easy to pair and makes on-bar control of bicycle lights a
breeze. The versatile remote mounts to both road or MTB bars and can be paired with up to 4 lights.
IMPORTANT: To use the Transmitr MicroRemote, you must have ANT+ compatible lights mounted on your
bicycle.
Compatible Bontrager lights:
• Ion Pro RT
• Ion 200 RT
• Ion 450 RT
• Flare RT
• Ion 800 RT
• Ion 700 RT
• Ion 350 RT
• Other ANT+ compatible lights
To set up any other light, please refer to the manual that came with your light.
Before you start
There are two phases to this installation: pairing the lights to the remote and attaching the lights and remote
to the bike. It is easiest to pair the lights to the remote before attaching it to the bike.
Verify pairing
1. Double-click the remote button to turn on all paired lights.
2. Press and hold the remote button for 1 second to turn off the light(s).
Remote operation with paired lights
When the Transmitr MicroRemote is used while lights are being used in auto mode with a Garmin, the
remote will take over changing the mode to individual on the Garmin. If a user wants auto mode to function
again, they'll need to select it again on the Garmin.
The remote will recognise available lights within 30 m (100 ft) as long as there is a clean line of sight.
• All lights will require a double-click to turn on.
• Once on, a single-click will change the mode of the front light, depending on the light type. A long press
will turn the lights off if they are on.
• The front light will operate in two configurations: High Mode Control or Mode Selection. The default out-
of-the-box experience is High Mode Control.
• The rear lights will only turn on and off.
Front light configurations
Each light will turn on to the last mode it was in when the remote turned the light off.
High mode control
If there is no saved mode, the light will turn on to LOW. Subsequent button presses will alternate the light
between HIGH and the previous mode.
Mode selection
By default, if there is no saved state, the lights will turn on to LOW. After this, each button press will
advance the lights through the mode list.
Example: High (click) -> Medium (click) -> Low (click) -> Night Flash (click) -> Day Flash
Change front light control mode
Hold down the button for 8 seconds. If you release the button between 8 and 15 seconds, the remote will
switch to the new control mode. It will flash to indicate which mode the remote is in: Red = High Mode
Control; Green = Mode Selection.
NOTE: If you do not release the button before 15 seconds, the remote will enter pairing mode.
Rear lights
The default setting is LOW. To change the saved mode, turn on the light. Use the button on the rear lights
to change the mode, then turn off the system using the remote.
Can't find light
If you are attempting to interact with a light and the remote can't find it, the remote will flash red for 2
seconds. And you must repeat the pairing process.
Low battery
If the battery on one of your lights has fallen below 5%, the remote lights up solid red for 2 seconds. This
will happen only when turning the system on, or turning the system off.
LED
Quick Mount CR1632
Battery