Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Genius ColorPage-Vivid 1200XE USB
Summary of Contents for Genius ColorPage-Vivid 1200XE USB
- Page 1 ColorPage-Vivid 1200XE USB...
-
Page 2: Table Of Contents
ColorPage-Vivid 1200XE USB uide Table of Contents Chapter 1. How to Handle Defective Returns ........................ 1 Overview ..................................1 Problems ..................................2 Problems Descriptions .............................. 2 Solutions of the problems............................2 Chapter 2. Assembly and Disassembly..........................4 How to Assembly and Disassembly the Scanner ......................5 How to Unlock the Lock Key ........................... -
Page 3: Chapter 1. How To Handle Defective Returns
Receiving Defective Scanners from Customers Verifying problems & poceeding necessary tests Functioning NG Analyzing possible malfunction causes Deciding & proceeding Functioning NG the rectification methods Functioning O K Replacing necessary defective parts Proceeding tests to verify if the scanner is founctioning normally Functioning O K Return the scanners with... -
Page 4: Problems
ColorPage-Vivid 1200XE USB uide Problems Descriptions 1 Main lamp unilluminated 2 No Scan (Including: Scanner not functioning or fail to activate TWAIN program, etc..) 3 Bad Motor 4 Poor Scanning Image 5 Others ( such as the Broken of the Defection Mirror or the Broken of the Document Glass, etc..) - Page 5 ColorPage-Vivid 1200XE USB uide No Scan (including: Scanner not functioning, or fail to activate TWAIN Program, etc..) Problem No Scan Analyze the Scan Board CCD Board Problem Identify the Defective Defective Problem Causes Scan Board CCD Board Solutions Replace...
-
Page 6: Chapter 2. Assembly And Disassembly
ColorPage-Vivid 1200XE USB uide Poor Scanning Image Problem Poor Scanning Image Analyze the Electronic Mechanical Problem Identify the Defective Defective Defective Incorrect Reflection Problem Causes CCD Board Scan Board CCD Focus Mirror Replace Replace Replace Re-adjust Solutions Reflection CCD Board... -
Page 7: How To Assembly And Disassembly The Scanner
ColorPage-Vivid 1200XE USB uide How to Unlock the Lock Key magnifier figure 2.1.1. figure 2.1.2. This scanner has a locking mechanism to hold the Scanner Module in place during transportation. The Auto Lock Key is located on the base of the scanner. Turn over the Scanner, then you can see the Auto Lock Key (figure 2.1.2). -
Page 8: How To Remove The Upper Cover
ColorPage-Vivid 1200XE USB uide How to Remove the Upper Cover How to Disassembly the Scanner Step 1 We will find a mortise-like and a tenon-like device, which fasten up the top cover and the base frame. figure 2.2.1. Step 2... - Page 9 ColorPage-Vivid 1200XE USB uide How to Remove the Document Glass Step 1 Please remove four Glass Stop Blocks shown below a & b 2 arrow points first. figure 2.3.1. Step 2 With a screwdriver, press down the left end of the Glass Stop Block, and then push it to the right.
-
Page 10: How To Remove The Sliding Axle And The Timing Belt
ColorPage-Vivid 1200XE USB uide How to remove the Sliding Axle and the Timing Belt Step 1 Hold the Sliding Axle & take out the Sliding Axle from the module so lightly. figure 2.4.1. Step 2 Move the module to the middle of the base frame. -
Page 11: How To Replace The Motor
ColorPage-Vivid 1200XE USB uide tweezers to take off the Timing Belt from Module. Magnify the point of Belt-fixed (A) Timing Belt To install the Sliding Axle and the Timing Belt, Outside of Inside of reverse the steps shown above. -
Page 12: How To Replace The Gear Wheel
ColorPage-Vivid 1200XE USB uide How to Replace the Gear Wheel Step 1 To remove the Gear Wheel, take out the E Ring (refer to figure 2.6.1.) with a tweezers. When installing, please install the Gear Wheel, and then using the Nipper to put the E Ring back. -
Page 13: How To Replace The Ccd Board
ColorPage-Vivid 1200XE USB uide How to Replace the CCD Board Step 1 Disconnect the FFC Cable. figure 2.8.1. Step 2 Dissolve the green seal on the screws on the scan board before you loosen them. figure 2.8.2. Step 3... -
Page 14: How To Replace The Ffc Cable
ColorPage-Vivid 1200XE USB uide How to Replace the FFC Cable Step 1 Pull out one end of the FFC Cable, which is attached to the Scan Board. Notice: While pulling out the FFC Cable, make sure that it is pull out with steady strength, otherwise, you may bend the FFC Cable, and result system failure. -
Page 15: How To Replace The Lamp
ColorPage-Vivid 1200XE USB uide Front Side Step 5 Notice: To connect the cable to the slot and to prevent the scanner from losing signal which will cause the IC burnout on the scanner board , please make sure that the connection is perfect. -
Page 16: How To Replace The Mirrors
ColorPage-Vivid 1200XE USB uide How to Replace the Mirrors Step 1 Loosen the 2 pcs screws of module cover with a screwdriver. figure 2.11.1. Step 2 Exert to push forward , then you can take apart the module cover. - Page 17 ColorPage-Vivid 1200XE USB uide Step 5 After remove the black seal, the five mirrors can be seen in the Scanner Module. Mirror A,B,C, D ,E are all fixed in mirror fix clips with black seal. figure 2.11.5. Step 6...
-
Page 18: How To Replace The Lens
ColorPage-Vivid 1200XE USB uide How to Replace the Lens Step 1 Need to loosen the 2 pcs screws, then you can open Screws the lens cover. figure 2.12.1. Screws Step 2 Loosen the 2 pcs screws of lens cover with a screwdriver. -
Page 19: Chapter 3. How To Adjust Ccd Resolution And Pixels
ColorPage-Vivid 1200XE USB uide Operation Flow Start Module Installation Preparation Formation Adjustment Scanner Center & Step’s Adjustment Adjustment Completed Module Finish... -
Page 20: Introduction Of Facilities And Tools
ColorPage-Vivid 1200XE USB uide Facilities: 1. Computer 2. CCD Adjustment Software figure 3.1.1. Tools: 1. Module Horizontal Resolution *2(600dpi;1200dpi) 2. Screwdriver (Cross type) *1 3. Green Seal *1 4. Torsional Driver *2 5. Tweezers *2 6. Nippers *2 figure 3.1.2. -
Page 21: Adjustment Procedures
ColorPage-Vivid 1200XE USB uide How to Adjust the Lens Resolution Step 1 Connecting the scanner to the computer. And activating the adjustment program according to the model you want to repair. ( refer to figure 12.1) Reset the system before proceeding any adjustment. - Page 22 ColorPage-Vivid 1200XE USB uide figure 3.2.2. (Adjustment Screen) Step 2 Place the Scanner Module on a Module Horizontal Resolution Adjustment tool. Loosen the screws then adjust lens resolution of the front and rear use the tweezers. figure 3.2.3. Step 3...
-
Page 23: How To Adjust The Ccd Points & Center Value
ColorPage-Vivid 1200XE USB uide How to Adjust the CCD Points & Center Value Step 1 Loosen the screws that adjust the CCD Board. With one hand to adjust the Scanner Center slightly to the right or left. After the Scanner Center is set, hold the CCD Board with one hand, and then adjust the CCD points slightly up or down. -
Page 24: Chapter 4. Important Notes
ColorPage-Vivid 1200XE USB uide PCB assembly is a kind of sophisticated electronic circuit board. A scanner mainly includes the following items: Scan Board, CCD Board, Switch Board, Panel Board, etc.. Therefore, well packing will be required when sending them by post or courier.