Table of Contents
Advertisement
DAILY CHECK
Lubricate items 1 thru
1. STEERING SPINDLE SHAFT
2.
UNIVERSAL
JOINT
3. LOWER STEERING SHAFT BEARING.
4. CLUTCH SHAFT
5. PULLEY (when in use)
ENGINE CLUTCH RELEASE BEARING -
6 .
Lubricate every 10 to 20 hours with chassis
lubricant.
Do not over grease. Fitting can
be reached by removing small cover at
bottom of clutch housing. Lock clutch pedal
forward to locate fitting 50 it may be reached
by gun.
7. FRONT WHEELS - If wide front axle is used
lubricate four king pins. (See 30 Day Check.)
8. OIL SUMP - Capacity
oil level to full mark on oil gauge rod. When
using low octane fuel drain to level of drain
cock located on right side of oil sump, every
10 hours and refill with fresh motor oil.
Above 90°F. use SAE 40
Above 32'F.
Above lOoF. use SAE 20W
Below lOoF. use SAE 1OW
9. BREATHER CAP - Wash in gasoline and dip
in motor oil - throw off excess oil before re-
placing.
Under
extremely
service the breather cap twice daily.
10. AIR CLEANER - Clean and refill oil cup.
Fill to level mark using motor oil of the
s a m e v i s c o s i t y a s u s e d i n o i l s u m p .
Under extreme dusty conditions service air
cleaner twice daily. Each season remove
the entire air cleaner and clean main body
and element thoroughly. Keep all connections
air tight.
11. HYDRAULIC PUMP - Oil used in hydraulic
pump must not foam. Check daily and keep
filled to high mark on bayonet gauge or to top
of filler neck on tractor not equipped with
bayonet
gauge.
Filler plug is upper front
plug on torque tube. NOTE: This same oil
also lubricates belt pulley bearings and
g e a r s .
Change oil twice a year.
A magnetic drain plug is located at the bot-
tom of the housing.
cleaned periodically. To completely drain
the pump control housing must also be
pump
drained.
Above 45OF.
Below 45OF.
LUBRICATION AND SERVICE GUIDE
with Chassis Lubricant.
6
quarts. Maintain
6
use SAE 30
dusty
conditions,
This plug should be
use SAE 2OW
SAE 1OW
use
12. RADIATOR - Capacity 3-l/2
cocks are located at bottom of radiator and
engine block ahead of carburetor.
WEEKLY
13. RIGHT HAND BRAKE PEDAL - Lubricate
with
chassis
lubricant.
14. ENGlNE
CLUTCH PEDAL - Lubricate with
chassis lubricant (not shown).
15. OIL SUMP - Drain and refill with fresh oil
every 60 hours when using gasoline. When
using low octane fuel drain completely and
refill every 40 hours. Drain plug is located
at bottom of oil sump. Keep filled to full
mark on bayonet gauge.
Above 90°F use SAE 40
Above 32OF use SAE 30
Above lOoF use SAE 20W
Below lOoF use SAE 1OW
16. FINAL DRIVES - Capacity l-3/4 quarts each.
Keep filled to level plug, For temperatures
above 32OF.
use SAE 140 gear lubricant; for
temperatures below 32'F. use SAE 90. Drain
and refill twice a year.
17. BATTERY - Electrolyte solution should be
l/4
inch above separators.
DAY CHECK
3 0
18. FRONT WHEELS - Clean and repack with
No. 2 wheel bearing grease every 30 to 60
days.
(Applies to all types of front wheels)
19. STEERING WORM AND GEAR - Check every
30
days.
to 60
front support, maintain oil level so worm
gear is one-third submerged. Use SAE 140
gear lubricant. NOTE: With wide front
axle and single front wheel use SAE #250.
20. GENERATOR - Lubricate with motor oil of
same viscosity as used in oil sump at pre-
vailing temperature. Two or three drops is
sufficient.
21.
TRANSMISSION,
TRANSMISSION CLUTCH - Capacity 17
quarts.
Keep filled to level plugs. Use
located on bottom of transmission, bottom
of differential and bottom of clutch housing.
Drain and refill twice a year. When power
take-off is installed on transmission add one
8
gallons. Drain
CHECK
Remove cover from top of
DIFFERENTIAL
D r a i n
p l u g s a r e
AND
Hide quick links:
Advertisement
Table of Contents
