Care Of The Fitness Machine; Walking Belt And Deck Lubrication; Walking Belt Adjustment - Bowflex TreadClimber TC5 Service Manual

Care of the TreadClimber Fitness Machine
®
To reduce the risk of electrical shock, always remove the batteries and wait 5 minutes before cleaning, maintaining or repairing this machine.
!
Read all maintenance instructions fully before you start any repair work. In some conditions, an assistant is necessary to do the necessary tasks.
Equipment must be regularly examined for damage and repairs. The owner is responsible to make sure that regular maintenance is done. Worn or damaged components
must be replaced immediately or the equipment removed from service until the repair is made. Only manufacturer supplied components can be used to maintain and repair
the equipment.
This product, its packaging, and components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This Notice is provided
in accordance with California's Proposition 65. If you would like additional information, please refer to our Web site at www.nautilus.com/prop65.
Daily: Before each use, inspect for loose, broken, damaged, or worn parts. Do not use the machine if any of these conditions exist. Use a dry cloth to wipe off any perspiration
after each use.
Weekly: Check for smooth roller operation. Clean the machine to remove dust, dirt, or grime. Clean the top of the belt with a damp, soapy cloth and wipe carefully and thoroughly
with a dry cloth. Do not let any liquid below the belts or into the Base Frame.
Monthly: Make sure all bolts and screws are tight. Tighten if necessary.
NOTICE: Do not clean with a petroleum based solvent or an automotive cleaner. Be sure to keep the Console free of moisture.

Walking Belt and Deck Lubrication

The TreadClimber fitness machine is equipped with a low maintenance deck and belt system. Belt friction can affect the function and life of the machine. For the best results
®
lubricate the Treadles periodically with a silicone lubricant, using the following instructions:
1. Remove the batteries from the machine.
2. Carefully lift each belt and apply silicone lubricant in the center of the Treadle deck along the entire reachable length of the deck. Apply 0.15 to 0.25 oz. of the lubricant on the
deck underneath each belt.
NOTICE: Always use a 100% pure silicone lubricant. Do not use a degreaser like WD-40® as this could seriously impact performance.
Note: The Walking Belts may need to be loosened to allow for access during lubrication. Consult the "Adjusting the Walking Belts" procedure if necessary.
3. Stay to one side of the machine and grasp the handlebars for support.
4. With one foot push the nearest belt toward the back of the machine at a very slow speed for approximately 15 seconds. Do not step on any excess lubricant, grease, or oil while
pushing the belt.
5. Take care to clean up any excess lubricant from the Treadles. We also recommend a periodic inspection of the Treadle surfaces below the belts. If the decks appear worn, contact
a TreadClimber® Representative (refer to the Contacts section of this manual).
To decrease the possibility of slipping, be sure the Treadle area is free from grease or oil. Clean off any excess oil from the machine surfaces.
Use the following timetable as a guide to lubricate the decks:
• Light user (fewer than 3 hours / week): every 3 months • Moderate user (3-5 hours / week): every 2 months • Heavy user (more than 5 hours / week): every month
We recommend that you use the following:
• Lube-N-Walk Treadmill Lubrication Kit (available from www.bowflex.com or your local specialty fitness dealer) • 100% pure silicone spray (available at most hardware and auto
®
parts stores)

Walking Belt Adjustment

The walking belts need to be adjusted if they are out of center enough to cause a rubbing or scraping sound. Adjustments can be made at the Front Roller of each Treadle (Item A).
Adjusting the Walking Belts – While operating the machine, notice where the belts run on each Treadle. The Walking Belt Adjustment Bolts are on the front end of each Roller.
If the belt is tracking too far to the right, use a 5 mm hex wrench to turn the right walking belt adjustment bolt clockwise on that belt in a half turn increment. Secure the hex
wrench and operate the walking belts for approximately 30 seconds, noticing if the walking belt is adjusted. Repeat as necessary until adjusted.
If the belt tracks too far to the left, do the same thing on the left walking belt adjustment bolt.
Note: Do not turn the bolts counterclockwise when you adjust the belt alignment.
Belt Tension Adjustment – Check the belt tension only when the machine is secured. From the belt's midpoint, a correctly tensioned belt should only have an inch of give. To
check, pull the belt upward at its midpoint and measure the distance to the deck. If the distance is more than an inch, the belt is loose. To tighten, turn both Walking Belt Adjust-
ment Bolts clockwise one-half a turn equally and check tension again. Repeat this step if necessary.
Note: Bolts are turned counterclockwise equally to decrease belt tension.
2