Download
Share
Print this page
DURKOPP ADLER 610-10 Additional Instructions
  1. Manuals
  2. Brands
  3. DURKOPP ADLER Manuals
  4. Sewing Machine
  5. 610-10
  6. Additional instructions
DURKOPP ADLER 610-10 Additional Instructions

DURKOPP ADLER 610-10 Additional Instructions

Replacing the dc motor at the tape unwinder
Hide thumbs Also See for 610-10:

Advertisement

Quick Links

Download this manual
610-10
Additional Instructions
Replacing the DC motor at the
tape unwinder

Advertisement

loading

Related Manuals for DURKOPP ADLER 610-10

Summary of Contents for DURKOPP ADLER 610-10

  • Page 1 610-10 Additional Instructions Replacing the DC motor at the tape unwinder...
  • Page 2 IMPORTANT READ CAREFULLY BEFORE USE KEEP FOR FUTURE REFERENCE All rights reserved. Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents, including extracts, is prohibited without the prior written approval of Dürkopp Adler AG. Copyright © Dürkopp Adler AG 2019...

  • Page 3: Table Of Contents

    Table of Contents General information ..............3 Replacing the DC motor at the tape unwinder......4 Disassembling the old motor ............4 Assembling the new motor ............7 Software settings..............10 Additional Instructions 610-10 - 00.0 - 04/2019...
  • Page 4 Table of Contents Additional Instructions 610-10 - 00.0 - 04/2019...

  • Page 5: General Information

    Check whether the scope of delivery for kit 9800 570006 S is correct prior to installation. Part number Quantity Designation 9800 570008 Motor + cable 0176 340110 Plate 0176 340220 USB key with software 0791 610701 EN Additional Instructions Additional Instructions 610-10 - 00.0 - 04/2019...

  • Page 6: Replacing The Dc Motor At The Tape Unwinder

    2. Remove cover (1). Fig. 2: Disassembling the old motor (2) ⑥ ③ ⑤ ③ ④ (3) - Circuit board (5) - Motor cable (4) - Screws (6) - Cable of the proximity switch Additional Instructions 610-10 - 00.0 - 04/2019...
  • Page 7 9. Remove the entire motor bracket. Fig. 4: Disassembling the old motor (4) ⑩ ⑪ (10) - Screws (11) - Old motor 10. Loosen the screws (10). 11. Take out the old motor (11). Additional Instructions 610-10 - 00.0 - 04/2019...
  • Page 8 Replacing the DC motor at the tape unwinder Fig. 5: Disassembling the old motor (5) ⑫ (12) - Plate 12. Unscrew all mounting parts from the plate (12). Additional Instructions 610-10 - 00.0 - 04/2019...

  • Page 9: Assembling The New Motor

    Replacing the DC motor at the tape unwinder 2.2 Assembling the new motor Fig. 6: Assembling the new motor (1) ① (1) - New plate To assemble the new motor: 1. Tighten all mounting parts on the plate (1). Additional Instructions 610-10 - 00.0 - 04/2019...
  • Page 10 4. Tighten the plate (1) on the tape unwinder using nuts (4) and washers. 5. Tighten the drive roller (5) on top of the motor shaft using screws (6). The 1 screw in the direction of rotation is located on the flat of the motor shaft. Additional Instructions 610-10 - 00.0 - 04/2019...
  • Page 11 8. Slide back the circuit board (9) and tighten it with the screws (10). Fig. 10: Disassembling the old motor (1) ⑪ ⑪ ⑫ ⑫ (11) - Cover (12) - Screws 9. Place the cover (11) and tighten it using the screws (12). Additional Instructions 610-10 - 00.0 - 04/2019...

  • Page 12: Software Settings

    Devices and select the subitem Tapefeeder Motor Type. Fig. 11: Software settings  The value entered here must be 1. 2. If the entered value is NOT 1, use the button panel to correct the value and confirm with OK. Additional Instructions 610-10 - 00.0 - 04/2019...
  • Page 14 DÜRKOPP ADLER AG Potsdamer Str. 190 33719 Bielefeld Germany Phone: +49 (0) 521 925 00 Email: service@duerkopp-adler.com www.duerkopp-adler.com...