Advertisement
Quick Links
Lateral/ Single Shelf Low Credenza • ONCSLFBK6020 • INSTRUCTIONS
Organize your parts and hardware. You will need (2) people, a Phillips head screwdriver and a rubber mallet.
TT-H
PED-L
PED-M
Parts :
LS-A: Back Panel
(28" x 17.25" x 1")
Quantity: 1
LS-E: Shelf
(28" x 17.75" x 1")
Quantity: 1
IMPORTANT NOTICE:
Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.
Check to be sure that you have all parts and hardware.
Remove all wrapping materials, including staples & packing straps before you start to assemble.
Do not tighten all screws/bolts until completely assembled.
Keep all hardware parts out of reach of children.
CARTONS: TT6020, PLF3020, PSC3020
LS-B: Base Panel
(28" x 19" x 1")
Quantity: 1
LS-F: Left Side
(19.75" x 17" x 1")
Quantity: 1
Parts List continued on back.
Any problems or questions call Regency Office Furniture at 1-866-816-9822
LS-F
LS-C: Top Panel
(28" x 16" x 1")
Quantity: 1
LS-G: Right Side
(19.75" x 17" x 1")
Quantity: 1
LS-B
Figure 1:
Cam Lock Assembly:
To open Cam, point arrow
toward Cam Pin hole. To
lock Cam, turn clockwise.
LS-D: Foot Bracket
(19.75"D)
Quantity: 2
TT-H: Credenza Top
(59" x 19.75" x 1")
(59" x 19.75" x 1")
Quantity: 1
Lateral/ Single Shelf
Low Credenza
Page 1
LS-G
LS-E
LS-A
LS-D
Advertisement
Related Manuals for Regency ONCSLFBK6020 TT6020
Summary of Contents for Regency ONCSLFBK6020 TT6020
- Page 1 Remove all wrapping materials, including staples & packing straps before you start to assemble. Do not tighten all screws/bolts until completely assembled. Keep all hardware parts out of reach of children. Any problems or questions call Regency Office Furniture at 1-866-816-9822...
- Page 2 Quantity: 4 P: Cam Caps S: 1” Top Screws Q: Glides R: Washers (25mm) Quantity: 14 Quantity: 8 Quantity: 12 Quantity: 8 T: Handles U: Connector Quantity: 4 Quantity: 2 Any problems or questions call Regency Office Furniture at 1-866-816-9822...
- Page 3 STEP 5 : Pull out each drawer on the Lateral(PED-L) and find the black tabs at the end of the suspension. Lift one side up and press the other side down simultaneously and pull the drawer out. This will unlock the drawer and release it. Repeat this for all drawers. Any problems or questions call Regency Office Furniture at 1-866-816-9822...
- Page 4 Figure 1A- Left Figure 1A- Right Figure 1 STEP 6C : Connect both components to one another by following Figure 2 and Figure 3 as shown below. Figure 2 Figure 3 Any problems or questions call Regency Office Furniture at 1-866-816-9822...
- Page 5 STEP 8 : Insert 4 Shelf Pins(N) in Open Storage Component at desired height and place Shelf(LS-E). Replace File Drawers and attach Handles(T). Finish by covering all Cam Locks with Cam Caps(P). Any problems or questions call Regency Office Furniture at 1-866-816-9822...