Related Manuals for Siemens FDM273-O
Summary of Contents for Siemens FDM273-O
- Page 1 FDM273-O Radio manual call point Mounting Building Technologies A6V10425648_en--_f 2016-11-28 Control Products and Systems...
- Page 2 Issued by: Siemens Switzerland Ltd. Building Technologies Division International Headquarters Gubelstrasse 22 CH-6301 Zug Tel. +41 41 724-2424 www.siemens.com/buildingtechnologies Edition: 2016-11-28 Document ID: A6V10425648_en--_f © Siemens Switzerland Ltd, 2014 2 | 18 Building Technologies A6V10425648_en--_f Fire Safety 2016-11-28...
-
Page 3: Table Of Contents
Table of contents About this document ................5 Mounting and installation ............... 6 Preparation ....................6 Installing the housing .................. 7 Installation ....................8 Installing the protective cover ..............10 Inserting the door sign ................11 Details for ordering ................12 Switching unit FDME273-O ................12 Housing FDMH273-R.................12 Battery pack BAT3.6-10 ................12 Key DMZ1195....................13... - Page 4 4 | 18 Building Technologies A6V10425648_en--_f Fire Safety 2016-11-28...
-
Page 5: About This Document
1 About this document Overview The FDM273-O radio manual call point is intended for use in areas of a house where a fire can be detected by people who can manually trigger an alarm. The FDM273-O radio manual call point consists of a housing, a switching unit, and a battery pack. -
Page 6: Mounting And Installation
Mounting and installation Preparation 2 Mounting and installation 2.1 Preparation Secure the housing at a height of 0.9…1.6 m on an even surface. Observe the country-specific regulations for the exact mounting height! 180° Figure 1: Opening the housing and identifying the screw holes 1 Screw opening 3 Break-out points 2 Door sign... -
Page 7: Installing The Housing
Mounting and installation Installing the housing 2.2 Installing the housing 2,5...3 mm >8 mm Figure 2: Example of securing onto the substructure using two screws w The housing is ready for mounting. See the chapter 'Preparation'. Screw the housing securely onto the substructure using two screws. a The housing has been installed. -
Page 8: Installation
Mounting and installation Installation 2.3 Installation 1 Screws 6 Battery pack BAT3.6-10 2 Switching unit FDME273 7 Holders 3 Battery connector 8 Locking lever 4 Housing FDMH273-R 9 Internal alarm indicator 5 Door 10 Alarm button Not included in the scope of delivery The flashing behavior of the internal alarm indicator is described in document A6V10425645 in the 'Internal alarm indicator' chapter. - Page 9 2. Remove the adhesive label with the serial number from the type plate on the switching unit. Use the adhesive label to mark the position of the radio manual call point FDM273-O on the device location plan. 3. Turn over the window sign if necessary, or use a different one.
-
Page 10: Installing The Protective Cover
Mounting and installation Installing the protective cover OUT OF ORDER AUSSER BETRIEB HORS SERVICE FUORI SERVIZIO FUERA DE SERVICIO BUITEN GEBRUIK Figure 3: 'NOT IN USE' label 2.4 Installing the protective cover If a protective cover (accessories) is used, proceed as follows: w A compatible protective cover is available. -
Page 11: Inserting The Door Sign
Mounting and installation Inserting the door sign 2.5 Inserting the door sign Only use the door sign if local regulations require the manual call point to be labeled in this way. w The appropriate door sign (printed on both sides) is available. 1. -
Page 12: Details For Ordering
Batteries with battery cable Connector system with protection against polarity reversal Inscription field for commissioning date Compatible with: – Radio manual call point FDM273-O – Radio manual call point FDM275-O – Radio fire detector FDOOT271-O Order number: S54370-Z11-A1 12 | 18... -
Page 13: Key Dmz1195
Details for ordering Key DMZ1195 3.4 Key DMZ1195 For opening doors on manual call points Compatible with: – Radio manual call point FDM273-O Order number: BPZ:4851910001 3.5 Glass insert DMZ1196-AC For alarm activation and protection against soiling Compatible with: –... -
Page 14: Specifications
Specifications Technical data 4 Specifications 4.1 Technical data You will find information on approvals, CE marking, and the relevant EU directives for this device (these devices) in the following document(s); see 'Applicable documents' chapter: Document A6V10431682 Device characteristics Detector diagnosis With Wireless diagnostic tool or connected fire control panel Type of alarm activation... - Page 15 Indoors Operating temperature -10…+55 °C Storage temperature -30…+75 °C Air humidity 95 % rel. Protection categories in accordance with IEC 60529: FDM273-O IP44 Housing FDMH273-R Electromagnetic compatibility: 10 kHz…100 kHz 160 V/m 100 kHz…2.5 GHz 30 V/m Mechanical data Weight: FDMH273-R 0.279 kg...
-
Page 16: Dimensions
Specifications Dimensions 4.2 Dimensions Radio manual call point FDM273-O 4.3 Master gauge for recesses Radio manual call point FDM273-O 61.5 37.5 37.4 61.8 27.8 16 | 18 Building Technologies A6V10425648_en--_f Fire Safety 2016-11-28... -
Page 17: Environmental Compatibility And Disposal
Specifications Environmental compatibility and disposal 4.4 Environmental compatibility and disposal This equipment is manufactured using materials and procedures which comply with current environmental protection standards as best as possible. More specifically, the following measures have been undertaken: Use of reusable materials Use of halogen-free plastics Electronic parts and synthetic materials can be separated Larger plastic parts are labeled according to ISO 11469 and ISO 1043. - Page 18 Issued by © Siemens Switzerland Ltd, 2014 Siemens Switzerland Ltd Technical specifications and availability subject to change without notice. Building Technologies Division International Headquarters Gubelstrasse 22 CH-6301 Zug +41 41-724 24 24 www.siemens.com/buildingtechnologies Document ID: A6V10425648_en--_f Manual FD20/FD720 Edition: 2016-11-28...