Advertisement
Quick Links
Doc. 15.215.00
TOYOTA
Part Number: 00016-34088
Accessory Code: BG3000
Conflicts
Models 1794 and Platinum
Kit Contents
Item #
Quantity Reqd.
1
2
2
1
3
1
4
1
5
2
6
1
7
1
8
1
DRL Hardware Bag Contents
Item #
Quantity Reqd.
1
1
2
1
3
1
4
8
5
2
Grille Hardware Bag Contents
Item #
Quantity.
Description
1
6
U-Nuts
2
8
#10 Screws
3
2
#8 Screws
4
2
5
2
Top Plate Extension Brackets (LH/RH)
6
2
Middle Extension Brackets (LH/RH)
7
2
Bottom Extension Brackets (LH/RH)
8
4
9
3
10
2
Recommended Tools
Safety Tools
Safety Glasses
Electrical Tape
Installation Tools
10mm Wrench
Phillips Screw Driver
Pliers
Side Cutters
Torque Wrench
Special Chemicals
3M Silicon Sealant
Southeast Toyota Distributors, LLC
Business Partner: J55
TUNDRA
Description
LED DRL
Driver Box
Switch
Hardware bags
Grille Assy
Logo Plate SR5
Logo Plate Limited
Description
Relay
Hood Wire Harness
Cabin Wire Harness
Wire ties
Black T-Taps
48" lbs
PIO / DIO Rev. A
2015
DRL Accessory Service Parts
Part Number
00016-32290-01
00016-32290-02
00016-32270-05
00016-32260-04
00016-32270-03
00016-32270-06
Grille Accessory Service Parts
Part Number
00016-34088-01
00016-34064-02
Recommended Sequence of Application
Item #
Accessory
1
LED DRL
2
Billet Grille
Mandatory
Page 1 of 16
01/07/15
Billet Grille w/LED DRL
X
X
X
X
X
X
X
X
Legend
Advertisement
Related Manuals for Toyota 00016-34088
Summary of Contents for Toyota 00016-34088
- Page 1 Doc. 15.215.00 Business Partner: J55 PIO / DIO Rev. A 01/07/15 TOYOTA TUNDRA 2015 Billet Grille w/LED DRL Part Number: 00016-34088 Accessory Code: BG3000 DRL Accessory Service Parts Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description...
-
Page 2: Installation
¼” slit in grommet and push the red, black, black-white and red-white wires through firewall. Note: Extra caution should be taken not to damage the connector’s pin. Seal with 3M Silicone sealant (picture 1) Picture A Southeast Toyota Distributors, LLC Page 2 of 16... - Page 3 Remove the driver’s side lower dash panel: remove two lower screws (picture 4) Picture 2 Picture 4 From inside the cabin, locate the wires that were pushed through in step 2. It will be the Picture 2A Southeast Toyota Distributors, LLC Page 3 of 16...
- Page 4 Picture 8: DRL red wire to connector J130 (light green wire) Picture 6 Connect the driver box to the wires pushed into the connectors on step 8 (make sure wire colors are aligned: black with black and red with red). Picture 8A Southeast Toyota Distributors, LLC Page 4 of 16...
- Page 5 15. Use an empty switch knock out on left panel, Secure ground (black) wire to bolt by the (left to the cargo light switch) and mount kick panel (picture 10) switch into switch knock out (picture 12). Southeast Toyota Distributors, LLC Page 5 of 16...
- Page 6 (picture 13). Picture 15 Picture 13 Remove four 10mm bolts from the plastic radiator cover then pull the radiator cover upward to remove (picture 14) Picture 15A Southeast Toyota Distributors, LLC Page 6 of 16...
- Page 7 (picture 17) Picture 19 Remove the factory Toyota logo from the factory grille by pressing the tabs on the back of the logo inward while pulling the logo forward ENGINE COMPARTMENT Run DRL’s wire harness from the large...
- Page 8 (next to the headlamp) to retrieve the harness (picture 21) Picture 20A Picture 21 Run the wire harness to the right side above the bumper, and secure with wire ties as shown (picture 22) Southeast Toyota Distributors, LLC Page 8 of 16...
- Page 9 (picture 26). Insure the u-nut is Secure excess wires with wire ties (pic. 24) oriented with the side that accepts the screw facing outward as shown. Picture 26 Picture 24 Southeast Toyota Distributors, LLC Page 9 of 16...
- Page 10 (picture 31). Picture 28 Take the two bottom extension brackets and install u-nuts onto the small ends aligning with the holes in the brackets and orient it as shown (picture 29). Southeast Toyota Distributors, LLC Page 10 of 16...
- Page 11 Billet. Secure the plate with the mounting plates on the bottom back of two 10/32” nylon lock nuts. the Billet align correctly. Picture 34 Picture 32 Southeast Toyota Distributors, LLC Page 11 of 16...
- Page 12 Billet and into the bottom extension brackets and tighten (picture 36). Southeast Toyota Distributors, LLC Page 12 of 16...
- Page 13 VEHICLE FUNCTION CHECK AFTER ALL PANELS, COVERS AND COMPONENTS THAT WERE REMOVED HAVE BEEN REINSTALLED, TEST THROUGHLY ALL MECHANICAL AND ELECTRICAL COMPONENTS DISCONNECTED AND/OR REMOVED FROM THE VEHICLE DURING THE INSTALLATION OF THIS ACCESSORY Southeast Toyota Distributors, LLC Page 13 of 16...
- Page 14 LED DRL 00016-34088 +12V at Connector J50 pin 1 Blue wire, +12V at Connector J130 Pin 8 Light Green wire Connects to Factory ground Parasitic current draw: 0.0 mA Southeast Toyota Distributors, LLC Page 14 of 16...
- Page 15 Pin'5'to'Ground '+12'VDC'when''ignition'switch'is'ON Connector'C-2,'C-3 Pin Wire'Color Test'Reference Proper'Operation Aproximately'0'VDC'when'igntion'switch'is'OFF Red'or'RedIWhite Pin'1'to'Ground Aproximately'0'VDC'when'ignition'switch'is'ON,'DRL'switch'is'OFF Aproximately'+18'to'+24'VDC'when'ignition'switch'is'ON,'DRL'switch'is'ON Black'or'BlackIWhite Pin'2'to'Ground Aproximately'0'VDC Connector'C-4 Pin Wire'Color Test'Reference Proper'Operation Black Pin'1'to'Ground Aproximately'0'VDC Approximately'0'VDC'ignition'switch'is'OFF' RedIYellow Pin'2'to'Ground Approximately'0'VDC'ignition'switch'is'ON,'DRL'switch'is'OFF' +12'VDC'when'ignition'switch'is'ON''and'DRL'switch'is'ON Aproximately'0'VDC'dash'panel'lights'are'OFF Blue Pin'3'to'Ground '+12'VDC'when'dash'panel'lights'are'ON Southeast Toyota Distributors, LLC Page 15 of 16...
- Page 16 RedIWhite Pin'3'to'Ground Approximately'0'VDC'ignition'switch'is'ON,'DRL'switch'is'OFF' +12'VDC'when'ignition'switch'is'ON''and'DRL'switch'is'ON Black Pin'3'to'Ground Aproximately'0'VDC Connector'C-6 Pin Wire'Color Test'Reference Proper'Operation Black Pin'1'to'Ground Aproximately'0'VDC Connector'C-7 Pin Wire'Color Test'Reference Proper'Operation Aproximately'0'VDC'when'ignition'switch'is'OFF Pin'1'to'Ground +12'VDC'when'ignition'switch'is'ON Connector'C-8 Pin Wire'Color Test'Reference Proper'Operation Aproximately'0'VDC'dash'panel'lights'are'OFF Blue Pin'1'to'Ground '+12'VDC'when'dash'panel'lights'are'ON Southeast Toyota Distributors, LLC Page 16 of 16...