Connecting An Hdmi ™ Or A Dvi Device To The Hdmi Input - Toshiba TheaterWide 51HX94 Owner's Manual

Connecting an HDMI
[1]
The HDMI input on your TV receives digital audio
and uncompressed digital video from an HDMI device
or uncompressed digital video from a DVI
This input is designed to accept HDCP
digital form from EIA/CEA-861/861B–compliant
electronic devices (such as a set-top box or DVD player with
HDMI or DVI output).
The HDMI input is designed for best performance with 1080i
high-definition video signals, but will also accept and display
480i, 480p, and 720p signals.
NOTE: NEVER CONNECT THIS TV
TO A PERSONAL COMPUTER (PC).
THIS TV IS NOT INTENDED FOR USE WITH A PC.
To connect HDMI devices, you will need:
• one HDMI cable (type A connector for each device)
For proper operation, it is recommended that you use
as short an HDMI cable as possible. You should not
encounter difficulty if you use an HDMI cable shorter
than 16.4 ft (5m).
HDMI cable transfers both video and audio. Separate
analog audio cables are not required (see illustration
below). Some CDVs (video CDs) may not output digital
audio signals. In that case, you may hear sound by
connecting analog audio cables. However, if you connect
analog audio cables with this connection, the HDMI
terminal on the TV will not receive the HDMI digital audio
signal and you will hear analog audio only.
See "Selecting the HDMI 1 or HDMI 2 audio mode" on
page 50.
HDMI device
VIDEO
L
L
TV
COLOR
VIDEO 1 VIDEO 2 STREAM
HD-1
OUT 1
S-VIDEO S-VIDEO
Y
OUT 2
P
B
TheaterNet
VIDEO VIDEO
P
R
L/ L/
MONO MONO L
AUDIO
AUDIO AUDIO
R
R R
IN
___________
HDMI, the HDMI logo, and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing, LLC.
51,57HX94(E)012-25 19
Chapter 2: Connecting your TV
™
or a DVI device to the HDMI input
[2]
device.
[3] program material in
[4]
consumer
HDMI OUT
AUDIO
R IN
OUT
R
TheaterNet
IEEE1394 EJECT
ANT1
1 (CABLE)
IN
2
AUDIO
COLOR
HDMI IN
STREAM
HD-2
R L
2 2
Y
1
P
B
ANT2
1
VIDEO
VAR
P
R
AUDIO
L/
MONO
L
L
CableCARD™ ANT (75
AUDIO
AUDIO
G-LINK
R
R R
OUT DIGITAL AUDIO OUT
Copyright © 2004 TOSHIBA CORPORATION. All rights reserved.
___________
[1]
HDMI = High-Definition Multimedia Interface.
[2]
DVI = Digital Video Interface.
[3]
HDCP = High-bandwidth Digital Content Protection.
[4]
EIA/CEA-861/861B compliance covers the transmission of
uncompressed digital video with high-bandwidth digital content
protection, which is being standardized for reception of high-definition
video signals. Because this is an evolving technology, it is possible that
some devices may not operate properly with the TV.
NOTE: To ensure that the HDMI or DVI device is reset properly, it is
recommended that you follow these procedures:
• When turning on your electronic components, turn on the TV first,
and then the HDMI or DVI device.
• When turning off your electronic components, turn off the HDMI or
DVI device first, and then the TV.
NOTE: If your HDMI/DVI device is not working, make sure the device is
plugged in to the corresponding HDMI IN port you are selecting.
To connect DVI devices, you will need:
• one HDMI-to-DVI adapter cable
(HDMI type A connector) for each device
For proper operation, the length of an HDMI-to-DVI
adapter cable should not exceed 9.8 ft (3m). The
recommended length is 6.6 ft (2m).
• one pair of standard analog audio cables for each
device
An HDMI-to-DVI adapter cable transfers video only. Separate
analog audio cables are required (see illustration below).
See "Selecting the HDMI 1 or HDMI 2 audio mode" on page 50.
DVI device
VIDEO AUDIO
L
L
TV
VIDEO 1 VIDEO 2
OUT 1 S-VIDEO S-VIDEO
Y
OUT 2
P
TheaterNet
VIDEO VIDEO
P
L/ L/
MONO MONO L
)
AUDIO
AUDIO AUDIO
R
R R
IN
9/12/04, 7:02 PM
DVI / HDCP
OUT
R IN
R OUT
R
TheaterNet
IEEE1394 EJECT
1
IN
2
AUDIO
COLOR COLOR
HDMI IN
STREAM STREAM
HD-1 HD-2
R L
2
Y 2
P 1
B B
1
VIDEO
VAR
P
R R
AUDIO
L/
L MONO
L
CableCARD™ ANT (75
AUDIO
AUDIO
G-LINK
R
R R
OUT DIGITAL AUDIO OUT
ANT1
(CABLE)
ANT2
)
19