BRP SEA-DOO Search and Rescue Series 2017 Operator's Manual
  1. Manuals
  2. Brands
  3. BRP Manuals
  4. Boat
  5. SEA-DOO Search and Rescue Series 2017
  6. Operator's manual
BRP SEA-DOO Search and Rescue Series 2017 Operator's Manual

BRP SEA-DOO Search and Rescue Series 2017 Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2017
OPERATOR'S
GUIDE
SEA-DOO SAR
®
SERIES
SEARCH AND RESCUE
https://www.boat-manuals.com/
2 1 9
0 0 1
8 8 2
Original Instructions
Original Instructions

Advertisement

Table of Contents
loading

Related Manuals for BRP SEA-DOO Search and Rescue Series 2017

Summary of Contents for BRP SEA-DOO Search and Rescue Series 2017

  • Page 1 2017 OPERATOR’S GUIDE SEA-DOO SAR ® SERIES SEARCH AND RESCUE https://www.boat-manuals.com/ 2 1 9 0 0 1 8 8 2 Original Instructions Original Instructions...
  • Page 2 O.T.A.S. Rotax ® Sea-Doo ® 4-TEC iControl Sea-Doo ® T.O.P.S. 219001882 en https://www.boat-manuals.com/ ®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates. ©2017 Bombardier Recreational Products Inc. and BRP US Inc. All rights reserved.

  • Page 3: Foreword

    PREDELIVERY CHECK LIST cue) personal watercraft (PWC). It is to ensure backed by the BRP warranty and a net- your new watercraft was prepared to work of authorized Sea-Doo personal your entire satisfaction. watercraft dealers ready to provide the...

  • Page 4: Safety Messages

    BRP reserves the right at any time to discontinue or The safety alert symbol indicates change specifications, designs, fea- a potential injury hazard.

  • Page 5: Table Of Contents

    TABLE OF CONTENTS FOREWORD ................1 Know Before you Go .
  • Page 6 TABLE OF CONTENTS CONTROLS (cont’d) 2) Engine START/STOP Button..........38 3) Engine Cut-Off Switch ............39 4) Throttle Lever ..
  • Page 7 TABLE OF CONTENTS OPERATING INSTRUCTIONS (cont’d) General Operating Recommendations........72 OPERATING MODES .............. . 75 Sport Mode .
  • Page 8 Beeper Code Information ........... . 128 WARRANTY BRP LIMITED WARRANTY – USA AND CANADA: 2017 SEA-DOO ®...

  • Page 9: Safety Information

    SAFETY INFORMATION ________ ________ https://www.boat-manuals.com/ SAFETY INFORMATION...

  • Page 10: General Precautions

    GENERAL PRECAUTIONS Avoid Carbon Monoxide flame many feet away from the en- gine. To reduce the risk of fire or explo- Poisoning sion, follow these instructions: All engine exhaust contains carbon – Use only an approved red gasoline monoxide, a deadly gas. Breathing car- container to store fuel.

  • Page 11: Special Safety Messages

    SPECIAL SAFETY MESSAGES Reminders Regarding Safe WARNING Operation Stopping distance will vary de- pending on initial speed, load, The performance of this watercraft wind, number of riders and water may significantly exceed that of other conditions. The amount of braking watercraft you may have operated.
  • Page 12 SPECIAL SAFETY MESSAGES braking effect on the rearward motion. watercraft damage. Debris may also Also note that your engine must be be picked up and thrown rearward by running to be able to use the brake. the jet pump onto people or property. The personal watercraft jet thrust can Keep the tether cord attached to the cause injury.
  • Page 13 SPECIAL SAFETY MESSAGES Do not exceed the payload or pas- Operation of this PWC by a person un- senger capacities for your watercraft. der 16 years of age, or a person with a Overloading can affect maneuverabil- disability that impairs vision, reaction ity, stability and performance.

  • Page 14: Hypothermia

    SPECIAL SAFETY MESSAGES When accelerating on a PWC with a laws are vigorously enforced. The use passenger(s), whether from a com- of drugs and alcohol, singly or in com- plete stop or while underway, always bination, decreases reaction time, im- do so progressively.

  • Page 15: Active Technologies (Icontrol)

    ACTIVE TECHNOLOGIES (iCONTROL) Introduction – Cruise mode – Slow speed mode iControl (intelligent Control sys- The O.T.A.S. (Off Throttle Assisted tems) provides environment Steering) is also controlled by the iTC. whereby the operator can control many systems without taking his Sport Mode hands off the handlebars.

  • Page 16: Ibr (Intelligent Brake And Reverse System)

    ACTIVE TECHNOLOGIES (iCONTROL) As you proceed under a constant cruis- – Neutral ing speed setting, hold the throttle – Braking. lever fully depressed in order to keep The operator commands the position your full attention to maintaining good of the iBR gate using either the throttle situational awareness.
  • Page 17 ACTIVE TECHNOLOGIES (iCONTROL) WARNING – It is important to inform the operator of a watercraft who intends to follow in a convoy formation, of the braking and maneuvering capability of your PWC, what the plume of water indicates, and that a greater dis- tance must be maintained be- tween watercraft.

  • Page 18: Safety Equipment

    SAFETY EQUIPMENT Required Safety – Dry suit (in cold weather/water oper- ations) Equipment – Footwear, gloves, safety goggles The operator and the passenger(s) or shatterproof glasses are also rec- must wear an approved Personal Flota- ommended. Some type of light- tion Device (PDF) that is suitable for weight, flexible foot protection is PWC use.
  • Page 19 SAFETY EQUIPMENT and age should be considered when selecting a PFD. The buoyancy pro- vided by the PFD should support your weight in water. The size of the PFD should be appropriate for the wearer. Body weight and chest size are com- mon methods used to size PFDs.
  • Page 20 SAFETY EQUIPMENT Weighing the Risks vs Benefits In order to decide whether or not you should wear a helmet, it is best to con- sider the particular environment you will be riding in, as well as other fac- tors such as personal experience. Will there be a lot of traffic on the water? What is your riding style? The Bottom Line...

  • Page 21: Practice Exercises

    PRACTICE EXERCISES It is always a good idea to practice and Avoiding an Obstacle get familiar with all controls, functions Practice obstacle avoidance (choose a and handling characteristics of this wa- virtual point on the water) by steering tercraft before venturing on the water. the watercraft and maintaining throt- Always secure the tether cord to the tle.

  • Page 22: Important Factors Not To Neglect

    PRACTICE EXERCISES Important Factors Not to Neglect In addition, always remember that the following conditions have a direct im- pact on how this watercraft will behave and respond to different inputs: – Loads – Currents – Wind – Water conditions. Make sure to be alert to these condi- tions, and adapt accordingly.

  • Page 23: Navigation Rules

    NAVIGATION RULES Operating Rules Operating a watercraft can be com- pared with driving on unmarked high- ways and roads. To prevent collisions or avoid other boaters, a system of op- erating rules must be followed. It’s not only common sense... it’s the law! smo2012-003-200 Generally keep to your right and safely TYPICAL...
  • Page 24 NAVIGATION RULES buoy, or to which channel you can con- This watercraft has the capability of tinue. They may also indicate whether turning more sharply than other boats, you are entering a restricted or con- however, unless in an emergency, do trolled area such as a no wake or low not negotiate sharp, high speed turns.

  • Page 25: Fueling

    FUELING Fueling Procedure WARNING Fuel tank may be pressurized, fuel WARNING vapors may be released while re- moving the fuel tank cap. Fuel is flammable and explosive under certain conditions. Always work in a well ventilated area. Do 8. Insert the gas pump spout into the not smoke or allow open flames or filler neck and fill up the fuel tank.

  • Page 26: Fuel Requirements

    FUELING Fuel Requirements Use of fuel labeled E15 is prohibited by U.S. EPA Regulations. NOTICE Always use fresh gaso- line. Gasoline will oxidize; the re- sult is loss of octane, volatile com- pounds, and the production of gum and varnish deposits which can damage the fuel system.

  • Page 27: Trailering Information

    TRAILERING INFORMATION NOTICE NOTICE The span of the trailer Do not route ropes or wood bunks including bunk width tie-downs over the seat or grab should be adjusted to provide sup- handle as they could be perma- port throughout the full length of the nently damaged.

  • Page 28: Important On-Product Labels

    IMPORTANT ON-PRODUCT LABELS Watercraft Safety Labels These labels are affixed to the vehicle for the safety of the operator, passenger(s) or bystanders. The labels illustrated on the following pages are on your watercraft. If missing or damaged, they can be replaced free of charge. See an authorized Sea-Doo dealer. Please read the following labels carefully before operating this watercraft.
  • Page 29 IMPORTANT ON-PRODUCT LABELS 219904636 LABEL 1 - MAIN WARNING LH 219903448B LABEL 2 - MAIN WARNING RH F18L0NY LABEL 4 219903184 LABEL 3 ________ ________ https://www.boat-manuals.com/ SAFETY INFORMATION...
  • Page 30 IMPORTANT ON-PRODUCT LABELS Certain components in the engine compartment may be very hot. Direct contact may result in skin burn. 219903132A 219903132 219904639 LABEL 5 LABEL 7 219904640 F00A2TY LABEL 8 LABEL 6 219904254 LABEL 9 smo2009-002-111_a LABEL 12 smo2009-002-109_a LABEL 10 smo2009-002-106_aen LABEL 13...
  • Page 31 IMPORTANT ON-PRODUCT LABELS 219903502 LABEL 14 219903501 LABEL 15 ________ ________ https://www.boat-manuals.com/ SAFETY INFORMATION...

  • Page 32: Product Information Labels

    IMPORTANT ON-PRODUCT LABELS Product Information Labels smo2014-008-001_k 219903177 LABEL 1 NOTICE 219904634 LABEL 3 (from 1-1/2 to 2 minutes) 219904387 LABEL 2 _______ ________ https://www.boat-manuals.com/ SAFETY INFORMATION...

  • Page 33: Compliance Labels

    IMPORTANT ON-PRODUCT LABELS Compliance Labels smo2014-008-001_l COMPLIANCE LABEL LOCATION EMISSION CONTROL INFORMATION THIS ENGINE IS CERTIFIED TO OPERATE ON UNLEADED GASOLINE AND CONFORMS TO U.S. EPA & CALIFORNIA EMISSION / EVAP REGULATIONS FOR MARINE SI ENGINES. ENGINE FAMILY FAMILLE DE MOTEUR LIMITE DES ÉMISSIONS DE LA FAMILLE ENGINE DISPLACEMENT...
  • Page 34 IMPORTANT ON-PRODUCT LABELS 219903510 LABEL 6 - TYPICAL 219903554_d LABEL 3 - CANADIAN COMPLIANCE NOTICE (TYPICAL) AUSTRALIAN BUILDERS PLATE Imported by BRP Australia Pty Ltd DATE 2015 Max persons 3 = 225 kg Max load = 295 kg Buoyancy Basic Flotation WARNING Alteration of the boat’s hull or permanent...

  • Page 35: Pre-Ride Inspection

    Each visit to your authorized BRP dealer is a great opportunity for your dealer to verify if your watercraft is included in any safety campaign. We also urge you to visit your authorized BRP dealer in a timely manner if you become aware of any safety related campaigns.
  • Page 36 PRE-RIDE INSPECTION Drain Plugs WARNING Secure bilge drain plugs. Check throttle lever operation be- fore starting the engine. If any fric- tion is felt in the throttle lever, refer to an authorized Sea-Doo dealer. iBR Lever Check the iBR lever for free and smooth operation.

  • Page 37: What To Do After Launching The Watercraft

    PRE-RIDE INSPECTION WARNING ITEM OPERATION Never inflate sponson more than Information Check operation 41 kPa (6 PSI). Inflating sponson Center more than the specified pressure Intelligent Brake may damage sponson and cause and Reverse Check operation personal injury. Never use high System (iBR) pressure to inflate sponson.
  • Page 38 PRE-RIDE INSPECTION Variable Trim System With the engine running in forward po- sition, use the VTS system to move the jet pump nozzle up and down alter- nately to check VTS operation. Con- firm the VTS position indicator move- ment in the information center. OPERATING INSTRUCTIONS Refer to subsection for detailed instructions.

  • Page 39: Watercraft Information

    WATERCRAFT INFORMATION _______________ https://www.boat-manuals.com/...

  • Page 40: Controls

    CONTROLS NOTE: Some vehicle safety labels are not shown on illustrations. For information WATERCRAFT SAFETY LABELS on vehicle safety labels, refer to subsection. smo2016-001-005_a 1) Handlebar The handlebar controls the direction of the watercraft. During forward opera- tion, turning the handlebar to the right steers the watercraft to the right and inversely.

  • Page 41: Engine Cut-Off Switch

    CONTROLS NOTE: If the START/STOP button is WARNING pressed and held without the tether Should the engine be stopped, the cord installed, the information cen- brake function (models with iBR) ter displays will stay on as long as the and watercraft directional control START/STOP button is held.

  • Page 42: Mode/Set Buttons

    CONTROLS 6) MODE/SET Buttons – Neutral – Braking. These buttons are located on the RH side of the handlebar. NOTE: A minimum of 25% lever travel is required to activate iBR functions. Press MODE button to scroll through various functions available through the information center.

  • Page 43: Cruise Button

    CONTROLS The UP/DOWN buttons are used to It is used to return to SPORT mode make a selection or change a setting after selecting the Touring mode if en- through the information center such gine is not stopped. OPERATING MODES Refer to subsec- –...

  • Page 44: Information Center (Gauges)

    INFORMATION CENTER (GAUGES) WARNING Do not adjust the display while riding, you could lose control. smo2012-001-007_a TYPICAL 1. Multifunction gauge 2. Analog speedometer 3. Analog tachometer Multifunction Gauge Features FEATURE DISPLAY Sport mode indicator Touring mode indicator Fuel level indication Hour meter display ECO mode indicator CRUISE mode indicator...

  • Page 45: Multifunction Gauge Description

    INFORMATION CENTER (GAUGES) Multifunction Gauge Description NUMERICAL DISPLAY 1. Numerical display indication 2. Unit of measurement of indication 15 14 7 smo2011-003-022_a 1) Multifunction Display The multifunction display is used to: – Display the WELCOME message on power up – Provide various indications as se- lected by the operator –...
  • Page 46 INFORMATION CENTER (GAUGES) AVAILABLE INDICATIONS IN NUMERICAL DISPLAY Indication by Watercraft speed default Engine RPM Clock CRUISE SPEED setting SLOW SPEED MODE setting VTS preset VTS settings Fuel consumption (instant and average) Fuel autonomy (distance and time to empty) Lap timer Top speed/RPM Average speed/RPM X = An X indicates a standard feature...
  • Page 47 INFORMATION CENTER (GAUGES) 5) Fuel Level Indication A bar gauge located in the bottom RH side of the multifunction display con- tinuously indicates the amount of fuel in the fuel tank while riding. HOUR METER DISPLAY 7) Water Depth Display NOTE: This feature is not available on the SAR.
  • Page 48 INFORMATION CENTER (GAUGES) 10) High Temperature Indicator The high temperature indicator comes ON when a high engine temperature or a high exhaust system temperature is detected. CHECK ENGINE LIGHT When the check engine light comes on, you may seek service from an au- thorized Sea-Doo dealer, repair shop, or person of your own choosing for HIGH TEMPERATURE INDICATOR...
  • Page 49 INFORMATION CENTER (GAUGES) ECO MODE INDICATOR iBR POSITION INDICATOR (Fuel Economy Mode) 15) SKI MODE Indicator OPERATING MODES Refer to subsec- The ski mode indicator is not active on tion for detailed instructions. the SAR model. 13) CRUISE Mode Indicator The cruise mode indicator comes ON when: –...

  • Page 50: Navigating The Multifunction Display

    INFORMATION CENTER (GAUGES) Navigating the Function Description Multifunction Display Compass A GPS incorporated in the information WARNING center provides the indication in the Do not adjust display while riding, multifunction display. you could lose control. The cardinal points, intermediate car- dinal points, as well as the azimuth the Selecting Functions watercraft is travelling are displayed...
  • Page 51 INFORMATION CENTER (GAUGES) MESSAGE DISPLAYED LAP TIMER FUNCTION EXAMPLE LAP TIME 1. 01'02'34 lap time displayed here 2. Lap number "1" displayed here 2. Press the SET button to enter the function, the lap timer will be acti- 5. To save the last lap and stop the vated and visible in the display.
  • Page 52 INFORMATION CENTER (GAUGES) To display the watercraft fuel con- sumption, carry out the following: 1. Press the MODE button repeatedly until FUEL CONSUMPTION is visi- ble in the multifunction display. LAP TIMER FUNCTION EXAMPLE 1. Total lap times 02'23'37 displayed here 2.

  • Page 53: Changing Numerical Display Indication

    INFORMATION CENTER (GAUGES) VTS Mode 3. Press the UP/DOWN button until the preferred indication is visible in The VTS MODE function is used to the multifunction display (as appli- manually set the VTS or change VTS cable to model). PRESET settings. –...

  • Page 54: Multifunction Gauge Setup

    INFORMATION CENTER (GAUGES) NOTE: Each of these functions be- come active ONLY when selected as the numerical display indication. Multifunction Gauge Setup Clock Setting 1. Press the MODE button repeatedly FUNCTION SELECTED - CHANGE until SETTINGS is visible in the mul- CLOCK OFFSET tifunction display.

  • Page 55: Analog Tachometer Description

    INFORMATION CENTER (GAUGES) If for some reason the GPS signal is lost, a default mode is used whereby, the speed is calculated using infor- mation received from other systems to provide an estimated watercraft speed. Analog Tachometer Description The tachometer provides an analog in- dication of the revolutions per minute (RPM) of the engine.

  • Page 56: Equipment

    EQUIPMENT NOTE: Some vehicle safety labels are not shown on illustrations. For information WATERCRAFT SAFETY LABELS on vehicle safety labels, refer to subsection. smo2014-008-001_d TYPICAL - MODEL WITH NAVIGATION LIGHTS AND INFLATABLE SPONSON SHOWN 1) Glove Box 2) Front Storage Compartment A small, storage compartment for per- sonal articles.

  • Page 57: Seat

    EQUIPMENT To remove the seat, pull up on the latch handle and lift the back end of the seat off the latch pin. Then pull the seat up and backwards to unhook the front of the seat from it's retainer and remove the seat from the watercraft.

  • Page 58: Passenger Handhold

    EQUIPMENT 4) Passenger Handhold The seat strap provides a handhold for a passenger to hold on to when riding. The sides of the molded grab handle at the rear of the seat also provide a hand- hold for a passenger. The rear portion of the molded grab handle provides a handhold for the spotter or boarding the watercraft from the water.

  • Page 59: Eyelets

    EQUIPMENT smo2009-002-133 smo2008-001-020_a TYPICAL - BOARDING STEP HELD DOWN TYPICAL FOR BOARDING FROM WATER 1. Front eyelet NOTICE Transom Eyelets – Never use the step for boarding a watercraft that is out of water. The transom eyelets can be used for: –...

  • Page 60: Bilge Drain Plugs

    EQUIPMENT CAUTION Never attach to the mast to pull a load. This can cause damage to the mast and/or water- craft. smo2014-008-003_a TYPICAL 1. Central eyelet smo2014-008-001_g 1. Rear mast NOTICE Do not use the central eyelet for towing. Use only for at- 10) Navigation Lights taching a rescue sled.

  • Page 61: Ropes

    EQUIPMENT smo2014-008-001_h smo2014-008-001_j 1. Sponson (on each side) 1. Running board (on each side) NOTICE Sponsons must be in- 14) Heavy-Duty Front flated to correct pressure at all times. Bumper MAINTENANCE Refer to section. The heavy duty front bumper protects 12) Ropes the front end of the watercraft.

  • Page 62: Break-In Period

    BREAK-IN PERIOD Operation During Break-In Period A break-in period of 10 operating hours is required before running the water- craft at sustained full throttle. During this period, maximum throttle should not exceed 1/2 to 3/4 opening. However, brief full acceleration and speed variations contribute to a good break-in.

  • Page 63: Operating Instructions

    OPERATING INSTRUCTIONS WARNING PRE-RIDE IN- Always perform the SPECTION before operating this watercraft. Be sure to read the SAFETY INFORMATION and the WATERCRAFT INFORMATION sec- tions and be thoroughly familiar with the iControl technology. Should any control or instruction not be F18A01Y fully understood, refer to an authorized Sea-Doo dealer.
  • Page 64 OPERATING INSTRUCTIONS NOTICE NOTICE In shallow water, keep speed to a minimum and avoid hard – Stay on center of the step. accelerations. Even though this wa- – Only one person at a time on the tercraft is equipped with an anti-de- step.

  • Page 65: How To Start Engine

    OPERATING INSTRUCTIONS Take hold of the seat strap to help main- tain your balance and step forward onto the footboards on either side of the seat. smo2009-002-149 TYPICAL smo2009-002-145 TYPICAL Sit astride the seat. Operator with a Passenger The operator climbs on the watercraft smo2009-002-150 in the same way as explained previ- TYPICAL...

  • Page 66: How To Stop The Engine

    OPERATING INSTRUCTIONS How to Stop the Engine WARNING In shallow water, debris may be WARNING picked up and thrown rearward by the jet pump onto people or prop- To maintain watercraft directional erty. control, the engine should be running until the watercraft is stopped.

  • Page 67: How To Engage Neutral

    OPERATING INSTRUCTIONS O.T.A.S. System WARNING (Off-Throttle Assisted Steering) Throttle should be applied and The O.T.A.S. (Off-Throttle Assisted handlebar turned to change the di- Steering) system provides additional rection of the watercraft. Steering maneuverability in off-throttle situa- efficiency will differ depending on tions.

  • Page 68: How To Engage Forward

    OPERATING INSTRUCTIONS How to Engage and Use If the watercraft is moving backwards, momentarily press the UP button. Reverse Reverse can only be engaged between idle speed and the threshold forward speed of 8 km/h (5 MPH). To engage reverse position, the iBR lever on the LH handlebar must be pulled in at least 25% of the lever travel.

  • Page 69: How To Engage And Use Braking

    OPERATING INSTRUCTIONS Available engine power is limited in CAUTION Steering direction reverse mode, which limits reverse in reverse is opposite of forward. speed. To steer the stern to port (left) in re- verse, turn the handlebar to star- WARNING board (right). To steer the stern to starboard (right), turn the handle- Only use reverse at slow speed bar to port (left).
  • Page 70 OPERATING INSTRUCTIONS WARNING CAUTION As the watercraft slows to a stop, the wake created Braking should be practiced in by the watercraft will catch up and open waters and at gradually in- tend to push the watercraft forward. creasing speeds in order to be- Ensure there are no obstacles or come fully familiar with the con- bathers in the direction of travel.

  • Page 71: How To Use The Variable Trim System (Vts)

    OPERATING INSTRUCTIONS When the nozzle is positioned in an CAUTION As the watercraft upward angle, the water jet directs the slows to a stop while braking in a bow of the watercraft upward. This po- turn, the wake created by the water- sition is used to optimize high speed.
  • Page 72 OPERATING INSTRUCTIONS With the watercraft operating in for- To select the highest trim position ward position, proceed as follows: recorded, double-click on the VTS UP button (bow up). 1. Press the VTS UP button once to trim the bow of the watercraft up to To select the lowest trim position the next trim position.
  • Page 73 OPERATING INSTRUCTIONS 6. Press the SET button to save PRE- SET 1 and display PRESET 2. 7. Press the VTS UP/DOWN button to change the PRESET 2 VTS position. Gauge will display setting 1 through 5 in the digital screen above PRE- SET 2.

  • Page 74: General Operating Recommendations

    OPERATING INSTRUCTIONS 4. Press the SET button to save the de- – Water intake grate sired setting and return to the main – Impeller display. – Wear ring. NOTE: The available VTS settings are between 1 and 5. WARNING NOTE: The VTS system cannot be In shallow water, debris may be fully tested without the engine operat- picked up and thrown rearward by...
  • Page 75 OPERATING INSTRUCTIONS WARNING It is important to inform the oper- ator of a watercraft who intends to follow in a convoy formation of the braking and maneuvering capabil- ity of your PWC, what the plume of water indicates, and that a greater distance should be maintained be- tween both of you.
  • Page 76 OPERATING INSTRUCTIONS NOTICE Even though this water- craft is equipped with an anti-debris water intake grate, it is still possi- ble that debris such as rocks, sand or other objects may damage the propulsion system in shallower wa- ter than 90 cm (3 ft). The hull protec- tion coating may not prevent dam- ages to the hull caused by collisions with obstacles.

  • Page 77: Operating Modes

    OPERATING MODES AVAILABLE OPERATING MODES Sport mode Touring mode ECO mode Cruise mode Slow speed mode X = Indicates a standard feature Opt = Indicates a feature available as an option N.A. = Not Applicable Sport Mode By default, the watercraft is in SPORT mode of operation when first started.

  • Page 78: Eco Mode (Fuel Economy Mode)

    OPERATING MODES Deactivating Touring Mode To deactivate Touring mode while rid- ing at speed, carry out the following: WARNING When deactivating touring mode, be sure to maintain situational awareness of other watercraft, ob- stacles, or persons in the water. MESSAGE DISPLAYED ECO MODE 1.

  • Page 79: Cruise Mode

    OPERATING MODES Cruise Mode 2. Press and hold the cruise button. Cruise mode is a function of iTC (in- telligent Throttle Control) system that allows the operator to set the desired maximum watercraft speed. This is useful when cruising for long distances, operating in limited speed zones or for towing.
  • Page 80 OPERATING MODES The following will be displayed in the multifunction gauge. CRUISE MODE INDICATOR Cruise Mode Activation Above Idle FUNCTION SELECTED - CRUISE Speed MODE To activate cruise mode above idle 1. CRUISE MODE _ SPEED speed (10 km/h (6 MPH)): ADJUSTING 1.

  • Page 81: Slow Speed Mode

    OPERATING MODES CRUISE MODE INDICATOR FUNCTION SELECTED - CRUISE MODE Changing Set Cruise Speed 1. CRUISE MODE _ SPEED To increase or decrease the set cruise ADJUSTING speed: 2. Cruise speed set point indication 1. Hold the throttle lever all the way in to the handlebar.
  • Page 82 OPERATING MODES The operator can select an idle speed set point (slow speed) be- tween 1 and 5 (1.6 km/h to 11 km/h (1 MPH to 7 MPH)). If you accelerate above approximately 14 km/h (9 MPH), Slow Speed Mode will be deactivated and the engine will return to its normal idle RPM when the throttle is released.
  • Page 83 OPERATING MODES sdd2009-001-024_i MESSAGE DISPLAYED TYPICAL SLOW SPEED MODE ACTIVE 1. UP button to increase speed 2. DOWN button to decrease speed Deactivating Slow Speed Mode While the UP/DOWN is being pressed to change the slow speed set point, Slow speed mode can be deactivated the following will appear in the multi- using any of the following methods: function gauge.

  • Page 84: Special Procedures

    SPECIAL PROCEDURES Jet Pump Water Intake and If the aforementioned method does not work, the following can be per- Impeller Cleaning formed: – With engine running and before ap- WARNING plying throttle, pull the iBR lever in Keep away from intake grate while to select reverse operation and vary engine is running.
  • Page 85 SPECIAL PROCEDURES WARNING If it is necessary to reach in to re- move any foreign object caught in the propulsion system, strictly observe the following before pro- ceeding: – Remove tether cord from the engine cut-off switch. – Wait at least 5 minutes. AVAILABLE MODE FUNCTION –...

  • Page 86: Capsized Watercraft

    SPECIAL PROCEDURES Capsized Watercraft NOTE: Use the UP/DOWN button on the RH handlebar to move the iBR to The watercraft is designed so that it the desired position once the iBR over- should not turn over easily. Two inflat- ride function has been activated as able sponsons mounted on the side of described in the previous steps.

  • Page 87: Submerged Watercraft

    SPECIAL PROCEDURES Water-Flooded Engine 4. If this method does not work, ask someone to assist you. NOTICE Never try to crank or start NOTE: The watercraft can be easily the engine. Water trapped in intake flipped back by a person weighting manifold would flow towards the more than 84 kg (185 lb).
  • Page 88 SPECIAL PROCEDURES smo2013-001-001_a 1. Cross over hose ______________ https://www.boat-manuals.com/...

  • Page 89: Maintenance Information

    MAINTENANCE INFORMATION _______________ https://www.boat-manuals.com/...

  • Page 90: Maintenance Schedule

    Sea-Doo dealer or any other establishment with which BRP has a commercial relationship. For emission-related warranty claims, BRP is limiting the diagnosis and repair of emission-related parts to the US EPA authorized Sea-Doo dealers. For more information, please refer to the EMISSION-RELATED WARRANTY contained herein.
  • Page 91 MAINTENANCE SCHEDULE A: ADJUST FIRST 50 HOURS OR 1 YEAR C: CLEAN EVERY 100 HOURS OR 1 YEAR I: INSPECT L: LUBRICATE EVERY 200 HOURS OR 2 YEARS R: REPLACE O: OPERATOR TO BE PERFORMED BY RS: REPAIR SHOP PART/TASK NOTE ENGINE Engine oil and filter...
  • Page 92 MAINTENANCE SCHEDULE A: ADJUST FIRST 50 HOURS OR 1 YEAR C: CLEAN EVERY 100 HOURS OR 1 YEAR I: INSPECT L: LUBRICATE EVERY 200 HOURS OR 2 YEARS R: REPLACE O: OPERATOR TO BE PERFORMED BY RS: REPAIR SHOP PART/TASK NOTE ELECTRICAL SYSTEM Spark plugs...
  • Page 93 MAINTENANCE SCHEDULE A: ADJUST FIRST 50 HOURS OR 1 YEAR C: CLEAN EVERY 100 HOURS OR 1 YEAR I: INSPECT L: LUBRICATE EVERY 200 HOURS OR 2 YEARS R: REPLACE O: OPERATOR TO BE PERFORMED BY RS: REPAIR SHOP PART/TASK NOTE iBR SYSTEM (intelligent Brake and Reverse) iBR lever...

  • Page 94: Maintenance Procedures

    MAINTENANCE PROCEDURES This section includes instructions for WARNING basic maintenance procedures. Should any leak or gasoline odor be present, do not apply electri- WARNING cal power or start the engine. You Turn off the engine and follow should seek service from an autho- these maintenance procedures rized Sea-Doo dealer, repair shop, when performing maintenance.
  • Page 95 MAINTENANCE PROCEDURES Engine Oil Level NOTICE Check level frequently and refill if necessary. Do not over- fill. Operating the engine with an improper level may severely dam- age engine. CAUTION Certain compo- nents in the engine compartment may be very hot. Direct contact may smo2011-003-010_a result in skin burn.

  • Page 96: Engine Coolant

    MAINTENANCE PROCEDURES Engine Coolant Level WARNING Check coolant level with engine cold. Never add coolant in cooling system when engine is hot. CAUTION Certain compo- nents in the engine compartment may be very hot. Direct contact may smo2011-003-010_b result in skin burn. TYPICAL Open seat.

  • Page 97: Ignition Coils

    MAINTENANCE PROCEDURES NOTE: The watercraft is level when it is in water. When on a trailer, raise trailer tow pole and block in this posi- tion when bumper rail is level. RECOMMENDED Add coolant, see ENGINE COOLANT for specification to adjust coolant level between marks as required.

  • Page 98: Spark Plugs

    MAINTENANCE PROCEDURES 5. Apply DOW CORNING 111DOW WARNING CORNING 111 (P/N 413 707 000) or Never remove an ignition coil from an equivalent on rubber seal contact a spark plug without disconnect- area. ing it from the wiring harness. Flammable vapors may be present in the bilge.

  • Page 99: Exhaust System And Heat Exchanger

    MAINTENANCE PROCEDURES Spark Plug Installation Flushing should be performed when the watercraft is not expected to be Prior to installation, ensure the contact used further the same day or when the surfaces of the cylinder head and spark watercraft is stored for any extended plug are free of grime.

  • Page 100: Ride Plate And Water Intake Grate

    MAINTENANCE PROCEDURES Ensure water flows out of jet pump while flushing. Otherwise, refer to an authorized Sea-Doo dealer for servic- ing. NOTICE Never run engine longer than 2 minutes. Drive line seal has no cooling when watercraft is out of water.

  • Page 101: Sacrificial Anode

    MAINTENANCE PROCEDURES Fuses Ride Plate and Water Intake Grate Inspection Fuse Removal and Installation Inspect ride plate and jet pump wa- ter intake grate for damage. See your Use the fuse remover/installer in- Sea-Doo dealer to have any damaged cluded in the fuse box to ease fuse part repaired or replaced.
  • Page 102 MAINTENANCE PROCEDURES ahead of the fuel tank just under the gauge area, attached to the battery holder. smo2011-003-011_c BATTERY AND FUSE ACCESS, FRONT STORAGE COMPARTMENT 1. Battery access panel smo2014-008-011_a TYPICAL 1. Fuse box 2. Fuel tank 3. Front storage compartment (access panel removed) To remove the fuse box cover, squeeze and hold locking tabs on both sides of...
  • Page 103 MAINTENANCE PROCEDURES Fuse Box 1 Description FUSE RATING DESCRIPTION — Not used 15 A Diagnostic connector START/STOP button 30 A 30 A Charge — Not used 30 A Battery — Not used — Not used Depth sounder (if so equipped) Gauge, OTAS and CAPS 10 A Cylinder 1 (ignition coil and injection)

  • Page 104: Inflatable Sponsons

    MAINTENANCE PROCEDURES Inflatable Sponsons Important Information on Sponson Inflation The sponsons must be inflated to the recommended pressure at all times SPONSON PRESSURE MINIMUM MAXIMUM 28 kPa (4 PSI) 41 kPa (6 PSI) F03L16Y It is normal to observe changes in air TYPICAL pressure of the sponsons as the fol- 1.
  • Page 105 MAINTENANCE PROCEDURES Inflate sponson to specification. Verify pressure using the valve adapter and a low pressure gauge (70 kPa (10 PSI)). NOTE: Seat valve adapter as quickly as possible onto valve opening and firmly maintain in position to avoid air loss.
  • Page 106 MAINTENANCE PROCEDURES Tear Repair of Less than 5 cm (2 in) Tear Repair of More than 5 cm (2 in) Deflate completely sponson to be re- Deflate completely sponson to be re- paired. paired. Cut a patch about 75 mm (3 in) larger Cut 2 patches about 75 mm (3 in) larger than the tear in every direction.
  • Page 107 MAINTENANCE PROCEDURES Repeat the same bonding procedure for the outer patch. Allow 24 hours to dry before inflating. Clean any glue excess. ______________ https://www.boat-manuals.com/...

  • Page 108: Watercraft Care

    WATERCRAFT CARE NOTICE Remove the watercraft from the water Never clean fiberglass every day. and plastic parts with strong deter- gent, degreasing agent, paint thin- ner, acetone, or other strong chemi- Post-Operation Care cal or petroleum type cleaner. Exhaust System and Heat Stains may be removed from the seat Exchanger Flushing and fiberglass using XPS ALL PUR-...

  • Page 109: Post-Operation Inspection

    WATERCRAFT CARE Post-Operation Inspection It is important to check the following after riding the watercraft, especially if it was used in shallow water. This will ensure that the watercraft is ready and in proper condition for the next outing. WARNING The post-operation inspection can help you monitor wear and deterioration before they become a problem.
  • Page 110 WATERCRAFT CARE ITEM OPERATION Check condition of sponsons and running boards. Also: Inflatable sponsons including running boards – Inspect cords. – Inspect and tighten shackles. Check condition: – Make sure mast is properly installed and check for any play. Tighten nuts if required.

  • Page 111: Storage And Preseason Preparation

    STORAGE AND PRESEASON PREPARATION Storage Fuel System Fuel System Protection WARNING XPS FUEL STABILIZERXPS FUEL STA- Because fuel BILIZER (P/N 413 408 601) (or equiva- flammable, should have lent) should be added in the fuel tank to an authorized Sea-Doo dealer, prevent fuel deterioration and fuel sys- repair shop, or person of your tem gumming.
  • Page 112 STORAGE AND PRESEASON PREPARATION 7. Apply anti-seize lubricant on spark plug threads, then reinstall them MAINTE- in the engine. Refer to NANCE PROCEDURES 8. Install the ignition coils, refer to MAINTENANCE PROCEDURES Engine Coolant Test If antifreeze is not replaced, test its smo2009-002-132_c density.

  • Page 113: Preseason Preparation

    NOTICE When component con- Inflatable Sponsons ditions seem less than satisfactory, replace using genuine BRP parts, or Wash the sponsons with soap and wa- equivalents. ter solution (use only mild detergent). Rinse thoroughly with fresh water.
  • Page 114 STORAGE AND PRESEASON PREPARATION This page is intentionally blank ______________ https://www.boat-manuals.com/...

  • Page 115: Technical Information

    TECHNICAL INFORMATION ______________ https://www.boat-manuals.com/...

  • Page 116: Watercraft Identification

    WATERCRAFT IDENTIFICATION The main components of the water- craft (engine and hull) are identified by different serial numbers. It may some- times become necessary to locate these numbers for warranty purposes or to trace the watercraft in the event of theft. Hull Identification Number The Hull Identification Number (HIN) is located on the boarding platform at the...

  • Page 117: Engine Emissions Information

    Manufacturer's EPA Emission Regulations Responsibility All 1999 and more recent Sea-Doo watercraft manufactured by BRP are Beginning with 1999 model year en- certified to the EPA as conforming to gines, PWC manufacturers of marine the requirements of the regulations for...

  • Page 118: Specifications

    SPECIFICATIONS SEA-DOO SAR ENGINE Rotax ® 1503 4-TEC ® . Single Over Type Head Camshaft (SOHC) Declared Power 106 kW @ 7300 RPM Induction Naturally-aspirated Number of cylinders 12 valves (4 per cylinder) with Number of valves hydraulic lifters (no adjustment) Displacement 1 494 cm³...
  • Page 119 5.5 L (5.8 qt (U.S. liq.)) Declared power as per ISO 8665 at propeller-shaft. NOTE: BRP reserves the right to make changes in design and specifications and/or to make additions to, or improvements in its products without imposing any obligation upon itself to install them on its products previously manufactured.
  • Page 120 SPECIFICATIONS This page is intentionally blank ______________ https://www.boat-manuals.com/...

  • Page 121: Troubleshooting

    TROUBLESHOOTING ______________ https://www.boat-manuals.com/...

  • Page 122: Troubleshooting Guidelines

    TROUBLESHOOTING GUIDELINES ENGINE WILL NOT START 1. Tether cord removed. – Properly install tether cord cap on engine cut-off switch . – After double “beep”, press START/STOP button to start engine. 2. Burnt fuse: main, electric starter or ECM. – Check wiring then replace fuse(s). 3.
  • Page 123 TROUBLESHOOTING GUIDELINES ENGINE TURNS NORMALLY BUT WILL NOT START (cont’d) 4. Water-flooded engine. – Refer to WATER-FLOODED ENGINE in SPECIAL PROCEDURES. 5. Engine management system fault detected (check engine pilot lamp is ON). – Seek service from an authorized Sea-Doo dealer, repair shop, or person of your own choosing for maintenance, repair, or replacement.
  • Page 124 TROUBLESHOOTING GUIDELINES ENGINE SMOKE (cont’d) 3. Internal engine damage. – Seek service from an authorized Sea-Doo dealer, repair shop, or person of your own choosing for maintenance, repair, or replacement. Please refer to the US EPA EMISSIONS-RELATED WARRANTY contained herein for information about warranty claims.
  • Page 125 TROUBLESHOOTING GUIDELINES ENGINE LACKS ACCELERATION OR POWER (cont’d) 8. Low fuel pressure. – Seek service from an authorized Sea-Doo dealer, repair shop, or person of your own choosing for maintenance, repair, or replacement. Please refer to the US EPA EMISSIONS-RELATED WARRANTY contained herein for information about warranty claims.
  • Page 126 TROUBLESHOOTING GUIDELINES ABNORMAL NOISE FROM PROPULSION SYSTEM 1. Weeds or debris jammed around impeller. – Clean. Refer to JET PUMP WATER INTAKE AND IMPELLER CLEANING in SPECIAL PROCEDURES subsection. – Check for damage. 2. Damaged impeller shaft or drive shaft. –...

  • Page 127: Monitoring System

    MONITORING SYSTEM A system monitors the electronic com- If there is an active fault code, it may ponents of the EMS (engine manage- be viewed by the operator on the mul- ment system), iBR (if equipped), and tifunction display. The operator may other components of the electrical then choose to call his authorized system.

  • Page 128: Fault Indicators And Message Display Information

    MONITORING SYSTEM APPLICABLE FAULT CODE IS DISPLAYED HERE Fault Indicators and Message Display Information The fault indicators and messages displayed in the information center will inform you of a particular condition or if an anomaly occurs. If a fault indicator or a fault message comes ON in the multifunction gauge, seek service from an authorized Sea-Doo dealer, repair shop, or person of your own choosing for maintenance, repair, or replacement.
  • Page 129 MONITORING SYSTEM MESSAGE DISPLAY INFORMATION RIGHT KEYPAD ERROR Gauge control button malfunction LOW OIL PRESSURE Engine low oil pressure detected HIGH EXHAUST TEMPERATURE High exhaust temperature detected HIGH TEMPERATURE High engine temperature detected Engine system malfunction or CHECK ENGINE maintenance required HIGH BATTERY VOLTAGE High battery voltage detected LOW BATTERY VOLTAGE...

  • Page 130: Beeper Code Information

    MONITORING SYSTEM Beeper Code Information BEEPER CODES DESCRIPTION Defective engine cut-off switch. Refer to an authorized Sea-Doo dealer. Improper operation of ECM or defective wiring 1 long beep harness. (when installing tether Seek service from an authorized Sea-Doo dealer, repair cord on engine cut-off shop, or person of your own choosing for maintenance, switch)

  • Page 131: Warranty

    WARRANTY ______________ https://www.boat-manuals.com/...

  • Page 132: Brp Limited Warranty - Usa And Canada: 2017 Sea-Doo Personal Watercraft

    BRP. BRP reserves the right to modify this warranty at any time, being un- derstood that such modification will not alter the warranty conditions applicable to the products sold while this warranty is in effect.
  • Page 133 RELATED WARRANTY contained herein. 4. For Sea-Doo personal watercrafts produced by BRP for sale in the State of Cali- fornia or New York that are originally sold to a resident or subsequently warranty registered to a resident in the State of California or New York, please also refer to the applicable California and New York Emissions Control Warranty Statement contained herein.
  • Page 134 BRP will not honour this limited warranty to any private use owner or commercial use owner if one of the preceding conditions has not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 135 9. CONSUMER ASSISTANCE In the event of a controversy or a dispute in connection with this BRP limited warranty, BRP suggests that you try to resolve the issue at the dealership level. We recommend discussing the issue with the authorized BRP dealer’s service manager or owner.

  • Page 136: Epa Emission-Related Warranty

    2. It is free from defects in materials and workmanship that may keep it from meeting the requirements of 40 CFR 1045 and 40 CFR 1060. Where a warrantable condition exists, BRP will repair or replace, as it elects, any part or component with a defect in materials or workmanship that would increase the engine’s emissions of any regulated pollutant within the stated warranty...
  • Page 137 Components Covered The emission-related warranty covers all components whose failure would in- crease an engine’s emissions of any regulated pollutant, including the following listed components: 1. For exhaust emissions, emission-related components include any engine parts related to the following systems: –...
  • Page 138 * In the USA, products are distributed and serviced by BRP US Inc. ______________...

  • Page 139: California And New York Emission Control Warranty Statement For Model Year 2017 Sea-Doo Personal Watercraft

    CALIFORNIA AND NEW YORK EMISSION CONTROL WARRANTY STATEMENT FOR MODEL YEAR 2017 SEA-DOO ® PERSONAL WATERCRAFT For California and New York, your 2017 Sea-Doo personal watercraft has a special environmental label required by the California Air Resources Board. The label has 1, 2, 3 or 4 stars.
  • Page 140 This emission limited warranty covers Model Year 2017 Sea-Doo personal wa- tercrafts certified and produced by BRP for sale in California or New York, that are originally sold in California or New York to a California or New York resident or subsequently warranty registered to a California or New York resident.
  • Page 141 Operator’s Guide. Emission warranty parts that are scheduled for replacement, as required mainte- nance, are warranted by BRP for the period of time before the first scheduled re- placement date for that part. Emission warranty parts that are scheduled for reg- ular inspection, but not regular replacement, are warranted by BRP for the entire warranty period of the personal watercraft.
  • Page 142 ® personal watercraft, you should however be aware that BRP may deny you warranty coverage if your engine(s) or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications. You are responsible for presenting your engine to an authorized BRP Dealer as soon as a problem exists.

  • Page 143: Brp International Limited Warranty: 2017 Sea-Doo Personal Watercraft

    BRP. BRP reserves the right to modify this warranty at any time, being understood that such modification will not alter the warranty conditions applicable to the products sold while this warranty is in effect.
  • Page 144 – Damage resulting from removal of parts, improper repairs, service, main- tenance, modification or use of parts or accessories not manufactured or approved by BRP which in its reasonable judgment are either incompatible with the product or adversely affect its operation, performance and durability, or resulting from repairs done by a person that is not an authorized servicing Sea-Doo Distributor/Dealer;...
  • Page 145 BRP will not honor this limited warranty to any private use owner or commercial use owner if one of the preceding conditions has not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 146 BRP reserves the right to improve or modify products from time to time without as- suming any obligation to modify products previously manufactured.
  • Page 147 For all other countries, please contact your local Sea-Doo Distributor/Dealer (visit our website at www.brp.com for contact information), or contact our North American office at: BOMBARDIER RECREATIONAL PRODUCTS INC. Consumer Assistance Center 75 J.-A. Bombardier Street Sherbrooke QC J1L 1W3 Tel.: +1 819 566-3366...

  • Page 148: Brp Limited Warranty For The European Economic Area, The Commonwealth Of The Independent States, Turkey: 2017 Sea-Doo Personal Watercraft

    BRP. BRP reserves the right to modify this warranty at any time, being understood that such modification will not alter the warranty conditions applicable to the products sold while this warranty is in effect.
  • Page 149 – Damage resulting from removal of parts, improper repairs, service, main- tenance, modification or use of parts or accessories not manufactured or approved by BRP which in its reasonable judgement are either incompatible with the product or adversely affect its operation, performance and durability, or resulting from repairs done by a person that is not an authorized servicing Sea-Doo Distributor/Dealer;...
  • Page 150 BRP will not honor this limited warranty to any private use owner or commercial use owner if one of the preceding conditions has not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 151 BRP reserves the right to improve or modify products from time to time without as- suming any obligation to modify products previously manufactured. 8. TRANSFER...
  • Page 152 ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY The following terms and conditions are applicable to products sold in France only: The seller shall deliver goods that are complying with the contract and shall be re- sponsible for defects existing upon delivery. The seller shall also be responsible for defects resulting from packaging, assembling instructions or the installation when it is its responsibility per the contract or if accomplished under its responsibility.

  • Page 153: Customer Information

    CUSTOMER INFORMATION ______________ https://www.boat-manuals.com/...

  • Page 154: Privacy Information

    PRIVACY INFORMATION BRP wishes to inform you that your coordinates will be used for safety and war- ranty related purposes. Furthermore, BRP and its affiliates may use its customer list to distribute marketing and promotional information about BRP and related products.

  • Page 155: Contact Us

    CONTACT US South America www.brp.com Rua James Clerck Maxwell, 230 North America TechnoPark Campinas SP 13069-380 Brazil 565 de la Montagne Street Valcourt (Québec) J0E 2L0 Asia Canada Sturtevant, Wisconsin, U.S.A. 15/F Parale Mitsui Building,8 10101 Science Drive Higashida-Cho, Kawasaki-ku...

  • Page 156: Change Of Address/Ownership

    In case of change of ownership, please join a proof that the former owner agreed to the transfer. Notifying BRP, even after the expiration of the limited warranty, is very important as it enables BRP to reach the watercraft owner if necessary, like when safety recalls are initiated.
  • Page 157 CHANGE OF ADDRESS/OWNERSHIP ______________ https://www.boat-manuals.com/...
  • Page 158 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________ https://www.boat-manuals.com/...
  • Page 159 CHANGE OF ADDRESS/OWNERSHIP NOTES ______________ https://www.boat-manuals.com/...
  • Page 160 CHANGE OF ADDRESS/OWNERSHIP NOTES ______________ https://www.boat-manuals.com/...
  • Page 161 CHANGE OF ADDRESS/OWNERSHIP NOTES ______________ https://www.boat-manuals.com/...
  • Page 162 CHANGE OF ADDRESS/OWNERSHIP NOTES ______________ https://www.boat-manuals.com/...
  • Page 163 https://www.boat-manuals.com/...
  • Page 164 GUIDE DU CONDUCTEUR, SÉRIE SEA-DOO SAR / ANGLAIS FAIT AU / MADE IN CANADA U/M:P.C https://www.boat-manuals.com/ ®™ AND THE BRP LOGO ARE TRADEMARKS OF BOMBARDIER RECREATIONAL PRODUCTS INC. OR ITS AFFILIATES. ©2017 BOMBARDIER RECREATIONAL PRODUCTS INC. ALL RIGHTS RESERVED. PRINTED IN CANADA.

Table of Contents