Spare Parts And Accessories - 3M PELTOR WS LiteCom Pro III Series Manual

GB
• Operating temperature range: -20°C to 50°C (122°F)
• Storage temperature range: -20°C to 50°C (122°F)
5.1 Removing and replacing cushions
H:1 H:2
H:1 To remove the cushion, slide your fingers under the edge
of the cushion and firmly pull straight out.
H:2 To replace, insert the foam liners.
H:3 Then, fit one side of the cushion into the groove of the
cup and then press on the opposite side until cushion snaps
in place.
5.2 Replacing the helmet attachment plate
I:2
I:1
For proper fitting on different industrial safety helmets, the
helmet attachment plate may need to be replaced. Find the
recommended attachment in Table B. The headset comes
assembled with P3E helmet attachment, while other plates
can be obtained from your dealer. A screwdriver is needed to
replace the helmet attachment plate.
I:1 Loosen the screw holding the plate and remove the plate.
I:2 Attach the appropriate plate while ensuring the left (L) and
right (R) designated plates are on the appropriate earmuff, if
applicable, and then tighten the screw.

6. SPARE PARTS AND ACCESSORIES

3M PELTOR HY83 Hygiene kit
TM TM
Replaceable hygiene kit consisting of two sets of foam liners
and two snap-in ear cushions. Replace at least twice a year
to ensure constant attenuation, hygiene and comfort.
3M PELTOR HY100A Clean – single-use protectors
TM TM
Single-use protector for the ear cushions. Package of
100 pairs.
3M PELTOR HYM1000 Mic Protector
TM TM
Moisture and wind-tight tape. Protects the speech micro-
phone. Package of 5 meters for about 50 replacements.
3M PELTOR M171/2 Wind shield for MT73 speech
TM TM
microphones
Wind noise protector for MT73-type speech microphones.
Two per package.
3M
phones
Wind noise protector for ambient sound microphones. One
pair per package.
H:3
3M™ PELTOR™ MT73 Dynamic microphone
Microphone boom with dynamic differential microphone
PELTOR M60/2 Wind shield for ambient micro-
TM TM
Intrinsically Safe Spare Parts
3M PELTOR ACK082 Rechargeable Li-Ion
TM TM
batterypack (only for WS™ LiteCom Pro III Headset
Ex)
3M PELTOR AL2AH Battery charging cable for
TM TM
ACK082
3M PELTOR FR08 Power Supply
TM TM
3M PELTOR FL5602-50 External PTT for WS
TM TM
LiteCom Pro III Headset, ATEX
Push-To-Talk button with connection cable for external
control of transmission with the radio in the
3M™ PELTOR™ WS LiteCom Pro III Headset.
TM
3M PELTOR MT90-02 Throat microphone
TM TM
Non Intrinsically Safe Spare Parts
3M™ PELTOR™ ACK081 Battery
3M™ PELTOR™ AL2AI Battery charging cable for
ACK081
3M PELTOR FR08 Power Supply
TM TM
3M PELTOR FL5602 External PTT for WS
TM TM
Pro III Headset
Push-To-Talk button with connection cable for
external control of transmission with the radio in the
3M™ PELTOR™ WS LiteCom Pro III Headset.
TM
3M™ PELTOR™ FL6CS Connecting cable
With 2.5 mm stereo connector for use with DECT and
mobile telephones.
3M™ PELTOR™ FL6BT Connecting cable
With 3.5 mm mono connector for use with a communica-
tion radio.
3M™ PELTOR™ FL6BR Connecting cable
With PELTOR™ J11 connector (type Nexus TP-120) for
use with a PELTOR™ adapter and an external commu-
nication radio. Contact your Authorised 3M™ PELTOR™
LiteCom Pro III Headset dealer for information.
3M PELTOR MT90-02 Throat microphone
TM TM
TM
LiteCom
TM