DeWalt D24000 Instruction Manual page 38

E N G L I S H
• Before replacing the top cover of the mains plug ensure that the cable
restraint (3) is holding the outer sheath of the cable firmly and that the
leads are correctly fixed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N) wires to the earth pin
marked E or .
For 115 V units with a power rating exceeding 1500 W, we recommend to
fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved extension cable suitable
for the power input of this machine (see technical data). The minimum
conductor size is 1.5 mm 2 .
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
2
Conductor size (mm ) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.515 25 30 45
Voltage Amperes Cable rating (Amperes)
230 0 - 2.0 6 6
2.1 - 3.4 6 6
3.5 - 5.0 6 6
5.1 - 7.0 10 10
7.1 - 12.0 15 15
12.1 - 20.0 20 20
Class I construction
This machine is of class I contruction; therefore earthed (grounded)
connection is required.
Mains plug for 230 V units
An earthed wall socket can be identified by the earth connection provided
to accept the earth pole on the mains plug.
Residual current device
The machine is equipped with a residual current device (RCD), which
protects the user against electric shock by interrupting the circuit when a
leakage current of 30 mA or greater is detected. For 115 V units the rated
leakage current is 5 mA.
38
60
6 6 6 6
6 6 6 6
6 6 10 15
10 10 15 15
15 15 20 20
20 20 25 -
Mains plug for 115 V units
Never operate the machine without the RCD in place.
Do not use the machine if the RCD does not function properly.
For the RCD to work, the machine must be connected to an
earthed wall socket.
Assembly
Prior to assembly always unplug the tool.
When assembling the machine, always follow the instructions
in the order as described below.
Unpacking the machine and its parts
When moving the machine, always seek assistance.
The machine is too heavy for one person to handle.
• Remove the loose packaging material from the box.
• Lift the machine parts out of the box.
• Remove any remaining packing material from the machine parts.
Mounting the motor frame to the support frame (fig. B1)
• Place the support frame (16) on a relatively smooth and level surface.
• Place the motor frame (17) on the support frame aligning the holes in
the foot (18) with the mounting holes (19).
• Insert a screw (20) into the holes.
• Tighten the screws using the Allen key (21) provided.
Mounting the sliding table to the support frame assembly (fig. B2 & B3)
• Make sure the lock (22) is in the unlock position.
• Hold the table in front of the frame, aligning the rollers (23) with the
roller rail (24).
• Place the rear roller onto the round rail.
• Slide the table onto the rail, making sure that the bearings (25) locate in
the slide rails (26).
• When the front of the table is approaching the frame, tilt the table
slightly to clear the stop (27).
• Lock the table in position by rotating the pin (22) and pushing it into the
hole (28) in the rail.
Placing the machine into the water basin (fig. B4)
• Place the water basin (13) on a relatively smooth and level surface.
• Fit the plug (29) into the drain hole.
• Lift and hold the machine at the carrying points as shown.
• Lower the machine into the water basin as shown.
Mounting the extension table (fig. C)
• Hold the extension table (6) in front of the right-hand side of the sliding
table (4).
• Align the positioning pins (30) on the extension with the holes (31) in
the sliding table.
• Place the extension against the sliding table.
• Tighten the clamp knob (32).
Installing the water pump (fig. D1 & D2)
• Fit the hose (33) onto the fitting (34).
• Place the water pump (35) in the deep corner of the water basin (13).
• Route the power cable and the water tube over the bottom of the
water basin as to avoid them from getting caught up by the sliding
table.