Maintenance And Storage; Assembly Instructions - Flymo Turbo Lite 250 Original Instructions Manual

10. Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12. Never pull on the cable to disconnect any of the plugs.
13. Use only on AC mains supply voltage shown on the
product rating label.
14. Our products are double insulated to EN60335. Under
no circumstances should an earth be connected to any
part of the product.
Cables
If extension cables are used, they must comply with the
minimum cross-sections in the table below:
Voltage Cable length
220-240V/ 50Hz Up to 20 m
220-240V/ 50Hz 20 - 50 m
Mains cables and extensions are available from your local
Approved Service Centre.
Only use extension cables specifically designed for
outdoor use and which conform to one of the following
specifications: Ordinary rubber (60245 IEC 53), Ordinary
PVC (60227 IEC 53) or Ordinary PCP (60245 IEC 57).
If the short connection lead is damaged, it must be
replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
Preparation
1. While using your product always wear substantial
footwear and long trousers. Do not operate the
equipment when barefoot or wearing open sandals.
Make sure the lawn is clear of sticks, stones, bones,
wire and debris; they could be thrown by the blade.
2. Before using the machine and after any impact, check
for signs of wear or damage and repair as necessary.
3. Replace worn or damaged blades together with their
fixings in sets to preserve balance.
Use
1. Use the product only in daylight or good artificial light.
2. Avoid operating your product in wet grass, where
feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and wear
non-slip footwear.
Fitting the lower handles to your lawnmower
(A)
A1 - lower handle
A2 - slots
A3 - fixing pin
1. Place the end of the lower handle into the slots.
2. Secure lower handles to hood by firmly pushing fixing
pin through holes in hood and handle.
3. Repeat on the other side.
NOTE: Should a problem occur when securing handle
to hood with the fixing pin, carefully lever fixing pin
out of location and repeat steps 1 to 3 above.
6
5. Operate your product across the face of slopes, never
6. Exercise extreme caution when changing direction on
7. Make sure you always take up a safe and stable
8. Do not walk backwards when operating, you could trip.
9. Never cut grass by pulling the product towards you.
10. Switch off before pushing the product over surfaces
Cross section
11. Never operate the product with damaged guards or
1.5 mm
2
12. Keep hands and feet away from the cutting means at
2.5 mm
2
13. Do not tilt product when the motor is running.
14. Never pick up or carry a product when it is operating
15. Remove the plug from the mains:
16. before leaving the product unattended for any period.
17. before clearing a blockage.
18. before checking, cleaning or working on the appliance.
19. if you hit an object. Do not use your product until you
20. if the product starts to vibrate abnormally. Check

Maintenance and storage

a CAUTION! Do not touch rotating blade(s).
1. Keep all nuts, bolts and screws tight to be sure the
2. Replace worn or damaged parts for safety.
3. Only use the replacement parts specified for this
4. Be careful during adjustment of the product to prevent
5. Store in a cool dry place and out of reach of children.
6. Allow the product to cool for at least 30 minutes before

ASSEMBLY INSTRUCTIONS

Fitting upper handles to lower handles (B)
B1 - lock off button
B2 - nut (if applicable)
B3 - handle knob
B4 - washer
B5 - bolt
1. Ensure the upper handle is located correctly with the
2. Ensure the upper handle and the lower handle are
3. Insert the nut into the handle knob. (if applicable)
4. Fit the bolts, washers and handle knobs.
5. Fit the cable to the handles with the clips provided.
up and down.
slopes. Walk never run.
stance whilst working, especially on slopes. Do not
use the mower close to swimming pools or garden
ponds.
other than grass.
without guards in place.
all times and especially when switching on the motor.
or still connected to the mains supply.
are sure that the entire product is in a safe operating
condition.
immediately. Excessive vibration can cause injury.
product is in safe working condition.
product.
entrapment of the fingers between moving blades and
fixed parts of the machine.
Do not store outdoors.
storing.
lock-off button on the switchbox uppermost.
aligned correctly.
Make sure the cable is not trapped between the upper
and lower handles.