Table of Contents
Advertisement
e) Be careful during adjustment of the machine to prevent entrapment of the
fingers between moving blades and fixed parts of the machine.
f) Always allow the machine to cool down before storing.
g) When servicing the blades be aware that, even though the power source is
switched off, the blades can still be moved.
h) Use only genuine replacement parts and accessories.
Additional safety warnings
Electrical safety
DANGER! Cardiac arrest!
This product makes an electromagnetic field while it operates. This
field may under some conditions interfere with active or passive medical
implants. To decrease the risk of conditions that can possibly injure or
kill, we recommend persons with medical implants to speak with their
physician and the medical implant manufacturer before you operate the
product.
Do not use under wet conditions.
Do not operate in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust.
Personal safety
DANGER! Risk of suffocation!
Small parts can be easily swallowed. There is also a risk that the polybag
can suffocate toddlers. Keep toddlers away when you assemble the
product.
Do not disassemble the product further than the delivery status.
Use gloves, wear slip resistant shoes and wear eye protection.
Do not overload the mower.
Never operate the product when you are tired, ill or under the influence of alcohol,
drugs, or medicine.
Danger of slipping:
- in wet grass
- on steep slopes
- during transport
Be careful while going backwards.
2. ASSEMBLY
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Disconnect the product from the mains and use gloves before
you assemble the product.
To assemble the handle [ Fig. A1 / A2 / A3 ]:
1. Slide the lower handles into the handle mounts.
2. Put the screws into the holes.
3. Screw the lower handles tight with the screws.
4. Slide the switchbox onto the switchbox mount.
5. Put the upper handle on the lower handles and slide the screws
through the boreholes (there are 2 holes in the lower handle to
choose the desired height).
6. Put the washers on the screws.
7. Screw the locking nuts onto the screws.
8. Attach the control cable with the cable clips.
To assemble the grass box [ Fig. A4 / A5 / A6 / A7 / A8 ]:
1. Push the grass box handle into the slots in the grass box cover until it
audibly engages.
2. Slide the grass box tongue into the slots in the grass box until it audibly
engages.
3. Align the grass box cover and the grass box locators.
4. Fold the grass box cover towards the grass box.
5. Push the grass box cover on the grass box. Make sure that all clips are
snapped in correctly.
To attach the grass box to the lawnmower [ Fig. A9 ]:
1. Lift the protective cover.
2. Attach the grass box to the hooks on the rear of the mower.
21300-85.960.02.indd 5
21300-85.960.02.indd 5
3. OPERATION
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from
the mains and use gloves before you adjust or transport
the product.
To adjust the cutting height:
For the first cut of the season, always cut on the highest cutting height
possible, and gradually lower the cutting height over successive cuts to
your desired height for the lawn.
300 (in 3 positions) [ Fig. O1 / O2 / O3 / O4 / O5 ]:
The cutting height can be adjusted from 20 – 60 mm.
Position 'Low' (20 mm): Cutting height setting should only be used on
well maintained 'manicured lawns' without excessive moss or thatch.
Position 'Mid' (40 mm): Cutting height setting is the suitable for most
lawns.
Position 'High' (60 mm): Cutting height setting is used when you lawn
has excessive growth such as following holidays or first cut of the season.
v Move both axles to the desired position in the E-Gate. Make sure
that both sides of the axle are in the same position. Make sure that
both axles are in the same position.
To start the mower [ Fig. O6 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start lever.
v Do not bypass the safety devices or switches. For example
do not attach the start lever to the handle.
To start:
The mower is fitted with a two-handed safety device (start lever
with starting lockout) to prevent the mower from being turned on
by accident.
1. Connect the mains cable to the mains.
2. Push the starting lockout with one hand and pull the start lever with
the other hand.
The mower starts.
3. Release the starting lockout.
To stop:
v Release the start lever.
The mower stops.
Tips to use the mower:
If grass residue is left in the discharge opening, pull the mower backwards
about 1 m so that the grass residue can drop out downwards.
To produce a well-maintained lawn and optimise the cutting performance,
we recommend to cut the lawn regularly once a week if possible. The lawn
becomes denser if you cut it frequently.
After relatively long cutting intervals (holiday lawn), first of all cut in one
direction with the highest cutting height and then cut in the crosswise
direction with the required cutting height.
If possible, only cut the grass when it is dry, if the grass is damp, the
cutting pattern will be uneven.
4. MAINTENANCE
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you maintain the product.
To clean the mower:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
5
05.10.21 14:06
05.10.21 14:06
Advertisement
Table of Contents
