Table of Contents
Advertisement
Tips
Poor reception
(in analogue mode)
The proximity of high buildings may be
responsible for ghost pictures, echoing or
shadows. In this case, try manually adjusting
your picture: see "fine tuning" (p.6) or change
the orientation of the outside aerial. In the
event of difficult reception (snowy picture)
switch the
NOISE.REDUCT
menu to
. (p. 7).
ON
Bad picture
(in digital mode)
If the picture freezes a lot, or in cases of block
effect, there is a problem of poor reception.
Please check with the
(see p.8).
Depending on the strength of digital terre s t r i a l
signals available in your are a ,s t a n d a rd aerials used
for analogue transmissions will in most cases
p rovide satisfactory reception of digital signals. I n
g e n e r a l , set top and communal aerials will not
g i ve satisfactory re s u l t s , best performance and
stability of digital signals can be achieved if a high-
quality aerial and wiring is installed.
If reception problems are experienced with a
s t a n d a rd aerial, a good quality, n a rrow beam
antenna should be pro fe s s i o n a l ly installed outside
the pro p e rty and aligned to cap t u re the maximu m
digital signal stre n g t h . Loft antenna's can be used
w h e re an outside installation is not possible,
h oweve r, c a re should be taken to mount the loft
antenna as high as possible and as far aw ay fro m
house wiring as possible.Aerial amplifiers should
o n ly be used when absolutely necessary. D o u b l e
s c reen coaxial cable should be installed betwe e n
the aerial and television re c e i ver and positioned to
avoid close proximity to house wiring.T h e
t e l evision re c e i ver should be connected dire c t ly to
the coaxial cable, rather than routing the signal
first through other pro d u c t s .
No picture
H ave you connected the aerial socket pro p e r ly ?
H ave you chosen the right system? (p. 6)
Is the contrast or the brightness badly adjusted?
È
Press
to select one of the smart control
presets.
Po o r ly connected euroconnector cables or aerial
s o c kets are often the cause of picture or sound
p roblems (sometimes the connectors can
become half disconnected if the TV set is move d
or turned). Check all connections.
Picture adjustment
If the picture is not adjusted properly or if you
have trouble obtaining a clear picture, select
on the
FEATURES
signal strenght
menu
one of the smart control presets
store using the
STORE PP ALL
menu.
FEATURES
The picture is too blue or too red! Adjust the
TINT
(p. 12).
In the event of difficult reception (snowy
picture) switch the
NOISE.REDUCT
menu to
PICTURE
ON
Peripheral equipment gives a black and
white picture
You have not selected the right socket with the
X
key: E2 instead of E2 Y/C.
To play a video cassette, check that it has been
recorded under the same standard (PAL,
SECAM, NTSC) which can be re p l ayed by the
video re c o rd e r.
No sound (in analogue mode)
If on certain channels you re c e i ve a picture but no
s o u n d , this means that you do not have the corre c t
TV system. Modify the SYSTEM setting (p. 6 ) .
The left and right loudspeakers on the TV set do
not work? Check that the external loudspeake r s
switch has not been activated by mistake (p. 2 0 ) .
The Surround Sound loudspeakers do not wo r k ?
For them to function corre c t ly it is essential that
both loudspeakers are connected: c h e c k
c o n n e c t i o n s .
If in doubt, use the SOUND LEVEL menu (p.13)
to check each channel.
Remote control
The TV set does not react to the remote
control; the indicator on the set no longer
flashes when you use the remote control?
Replace the batteries.
Press the TV key to be sure your remote
control is in the TV mode
Standby
When you switch the TV set on it remains in
s t a n d by and the indication LOCKED is displaye d
when you use the keys on the TV set? The
CHILD LOCK function is switched on (p. 7).
If the set receives no signal for 15 mins, it
automatically goes into standby mode.
The set consumes energy when it is switched
on.To save electricity, we recommend that you
switch the TV set off using the ON/OFF key.
Still no results?
If your TV set breaks down, never attempt to
repair it yourself: contact your dealer's after-
sales service.
È
(p. 8) and
function in the
on the
. (p. 12).
27
Advertisement
Table of Contents
