Specifications - Philips AVENT SCD860/27 Manual

WiFi status light signals
1 Off
- The baby monitor is off
2 Orange
- Flashes fast: the baby monitor is starting up.
- Flashes slowly: the baby monitor is upgrading its firmware. Do not turn
the baby monitor off during the firmware upgrade.
Note: The WiFi status light might turn off shortly during the firmware upgrade.
- Solid: the camera of the baby monitor is ready to read the WiFi QR
code generated by your smartphone or tablet.
3 Green
- Flashes slowly: the WiFi QR code has been read successfully.
- Solid: the baby monitor is connected to the WiFi network.
4 Red
- Flashes slowly: the WiFi password entered is wrong.
- Solid red: the baby monitor fails to connect to the WiFi network.
Resetting the baby monitor
The baby monitor has a reset button on the back. When you press this
button the baby monitor is reset to its factory default settings.
Note: Always reset the baby monitor by pressing the reset button and delete
your account before you transfer the baby monitor to someone else. This is
necessary to protect your privacy.
How to reset to factory default settings
While the baby monitor is on, press the reset button on the back
1
of the baby monitor with a paperclip or another pointed object.
It is recommended to do this when the baby monitor is connected
to your WiFi network (Fig. 13).
Keep the reset button pressed until the baby monitor beeps.
2
What to do after a reset to factory default settings
After the baby monitor has been reset, you need to reconnect it to
the WiFi network. If you invited other people to access the baby monitor,
you need to invite them again.
Cleaning and maintenance
- Do not immerse the baby monitor in water, and do not clean it under
running water.
- Do not use cleaning spray or liquid cleaners.
- Unplug the baby monitor if it is connected to a power outlet.
- Clean the baby monitor with a damp cloth.
- Clean the adapter with a dry cloth.
- This baby monitor has no other user serviceable parts.
Frequently asked questions
For more frequently asked questions, check the relevant section in the app.
Question Answer
Where can I You can find the user manual online at www.philips.com/
ugrow. The user manual is also available inside the app.
find the user
manual? Tap on 'Support' in the left tray to open the user manual.
I have problems Make sure that you hold the WiFi QR code at approx.
making my baby 8 inch (20cm) distance from the lens. Try moving the
monitor read smart device slightly up or down or left or right to ensure
the QR code the WiFi QR code is directly in front of the baby monitor.
on my smart You can also try moving the smart device closer to or
device. What further away from the baby monitor lens to allow proper
can I do? focusing. Make sure that there is enough light in the room,
but avoid too bright light. When the baby monitor has
read the WiFi QR code, it beeps to confirm.
Perhaps you did not remove the protective foil from
the baby monitor lens. Remove the foil.
Perhaps part of your hand covers the WiFi QR code.
Hold your device in such a way that your hand does
not cover the WiFi QR code.
I cannot Please check if any of the following factors prevent a
download and smooth download. Is your WiFi signal stable and strong
install the app. enough? Does your smart device run on iOS 7 or higher,
What can I do? or Android 4.1 or higher? Do you have enough space left
on your smart device to save the app? Did you enter the
correct password for the App Store or Google Play?
Disposal
This product may contain lead and mercury. Disposal of these materials
may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or visit
www.recycle.philips.com.
Storage precautions
- Do not expose the baby unit and parent unit to extreme cold or heat
or to direct sunlight.
- Do not put the baby unit and the parent unit close to a heating source.
Replacement
- If you need to replace the adapter, please refer to the user manual
and contact the Philips Customer Care Center.
- Supplied AC/DC Adapter. Input: 100-240V AC. Model No.:
S005AJU0500100. Output: 5 V DC, 1000 mA, (US plug).
- To buy accessories or spare parts, visit our online shop at
www.shop.philips.com/service. You can also contact the Philips
Consumer Care Center in your country (see the worldwide guarantee
leaflet for contact details). If there is no Consumer Care Center available
in your country, go to your Philips dealer or a Philips service center.
Compliance information
- This device complies with Part 15 of the FCC Rules and Industry
Canada License-exempt RSS standard. Operation is subject to the
following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation (Fig. 14).
Radio interference
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules and ICES-003 of
Industry Canada. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 7 3/4 inches / 20 centimeters
between the radiator and your body. For handheld/body-worn operation,
this equipment has been tested and meets the FCC RF/Industry Canada RF
exposure guideline when used with the belt clip supplied with this product.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter. Use of other accessories may not ensure
compliance with FCC RF/Industry Canada RF exposure guidelines.
This equipment also complies with Industry Canada RSS-102 with respect
to Canada's Health Code 6 for Exposure of Humans to RF Fields.
Do not attempt to repair or modify this equipment.
Any repairs or alterations made by the user to the equipment may void the
warranty and compliance of the equipment. Changes or modifications made
to this equipment not expressly approved by Philips Avent may void the
FCC authorization to operate this equipment. For assistance visit our website
www.philips.com/avent or contact the Philips Consumer Care Center in
your country. You find contact details in the worldwide guarantee leaflet.
Electromagnetic fields (EMF) This Philips Avent appliance complies with all
applicable standards and regulations regarding exposure to electromagnetic fields.

Specifications

General
AC power adapter:
- Rated input
- Rated frequency
- Rated output - adapter
Connectivity:
Apps
100-240 V
50-60 Hz
5V DC , 1 A
WiFi 802.11 b/g/n, 2.4 GHz