ADT Safewatch Pro 3000 Programming Manual page 6

PAGER OPTIONS 160-172
✱ 160 PAGER 1 PHONE No.
✱ 161 PAGER 1 CHARACTERS
✱ 162 PAGER 1 REPORTING OPTIONS
✱ 163 PAGER 2 PHONE No.
✱ 164 PAGER 2 CHARACTERS
✱ 165 PAGER 2 REPORTING OPTIONS
✱ 166 PAGER 3 PHONE No.
✱ 167 PAGER 3 CHARACTERS
✱ 168 PAGER 3 REPORTING OPTIONS
✱ 169 PAGER 4 PHONE No.
✱ 170 PAGER 4 CHARACTERS
✱ 171 PAGER 4 REPORTING OPTIONS
✱ 172 PAGER DELAY OPTION FOR ALARMS
REPORTING OPTIONS 173-177
✱ 173 RF REPORTING OPTIONS
✱ 174 CLEAN ME REPORTING OPTIONS
(for ESL smoke detectors)
✱ 175 UP AND ABOUT TIME
✱ 176 LACK OF USAGE OPTION
| | | | | | |
Enter up to 20 digits. 0–9; #+11 = ' ✱ '; #+12 = '#'; #+13 = 2-second pause.
| | | |
Enter the optional prefix characters, up to 16 digits.
0–9; #+11 = ' ✱ '; #+12 = '#'; #+13 = 2-second pause.
Part. 1 Part. 2 common
[0,0,0]
| | | | | | |
Enter up to 20 digits. 0–9; #+11 = ' ✱ '; #+12 = '#'; #+13 = 2-second pause.
| | | |
Enter the optional prefix characters, up to 16 digits.
0–9; #+11 = ' ✱ '; #+12 = '#'; #+13 = 2-second pause.
Part. 1 Part. 2 common
| | | | | | |
Enter up to 20 digits. 0–9; #+11 = ' ✱ '; #+12 = '#'; #+13 = 2-second pause.
| | | |
Enter the optional prefix characters, up to 16 digits.
0–9; #+11 = ' ✱ '; #+12 = '#'; #+13 = 2-second pause.
Part. 1 Part. 2 common
| | | | | | |
Enter up to 20 digits. 0–9; #+11 = ' ✱ '; #+12 = '#'; #+13 = 2-second pause.
| | | |
Enter the optional prefix characters, up to 16 digits.
0–9; #+11 = ' ✱ '; #+12 = '#'; #+13 = 2-second pause.
Part. 1 Part. 2 common
[3]
[3]
[0]
[0]
[0]
– 6 –
| | | | | | | |
| | | | | | | |
For each partition, select from the following options:
0 = no reports sent
1 = Open/closes all users
4 = All alarms and troubles
5 = All alarms / troubles, and open/closes for all users
12 = Alarms / troubles for zones entered in zone list 9
13 = Alarms / troubles for zones entered in zone list 9,
and open\closes for all users
| | | | | | | |
| | | | | | | |
See field *162 for reporting options. Select for each
[0,0,0]
partition (use zone list 10 if using options 12 or 13).
| | | | | | | |
| | | | | | | |
See field *162 for reporting options. Select for each
0,0,0]
partition (use zone list 11 if using options 12 or 13).
| | | | | | | |
| | | | | | | |
See field *162 for reporting options. Select for each
[0,0,0]
partition (use zone list 12 if using options 12 or 13).
0 = none, 1 = 1 minute, 2 = 2 minutes, 3 = 3 minutes
This delay is for ALL pagers in the system.
NOTE: The delay does not reset for new alarms
occurring while an existing pager delay is in progress.
0 = disable all options
1 = RF Tamper reports during disarm
2 = RF button types send low battery
8 = RF low battery reports delayed (delayed 28 days)
Example: Entering "10" (8 + 2) enables button-type
transmitters to send low battery reports and delay all
reports for 28 days. UL: see Inst. Instr. for requirements
0 = disable; 1 = Clean Me signal reports;
2 = Clean Me reports, 28-day enabled.
Note: If Clean Me is enabled, you must enter "3" in
field ✱56 programming for zone 1 response time.
0 = none, 1 = 1 hour, 2 = 2 hours,... 15 = 15 hours
(hourly increments)
1–15 = number of weeks selected (1 week increments)
If panel is not armed within the time period selected, a
report will be sent to the central station.
| | | |
| | |
| | | |
| | |
| | | |
| | |
| | | |
| | |