Introduction; Clearances/Height Requirements; Chimney System - Superior CUSTOM SERIES CR-3835L Installation Instructions Manual

The most important areas of concern dealing
with the installation of factory-built fireplaces are
clearances to combustible materials, proper as-
sembly of component parts, height of the chim-
ney system, the proper use of accessories sup-
plied by the manufacturer and the techniques
employed in using finishing materials applied to
the wall surrounding the fireplace, hearth exten-
sions and wall shields. Each of these topics will
be covered in thorough detail throughout this
manual. Please give each your special attention
as you progress with your installation.

INTRODUCTION

General Information
These fireplaces are conventional radiant heat
fireplaces with standard bar grates, optional
outside combustion air kits and optional deco-
rative glass doors.
These fireplaces have been tested and listed by
Omni Test Labs (Report No.116-F-20-4) to
U.L. standard 127. These units are intended
for installation in residential homes and other
buildings of conventional construction includ-
ing commercial, not in mobile homes.
TYPICAL INSTALLATION
Outside
Combustion
Air Kit
(Optional)
Figure 1
Note: Illustrations shown reflect "typical"
installations with nominal dimensions and
are for design and framing reference only.
Actual installations may vary due to indi-
vidual design preferences. However, always
maintain minimum clearances to combus-
tible materials and do not violate any specific
installation requirements.
These fireplace systems are designed for in-
stallation in accordance with the National Fire
Protection Standard for chimneys, fireplaces
and solid fuel burning appliances; NFPA 211
and in accordance with codes such as the
BOCA Basic/National Codes, the Standard Me-
chanical Code and the Uniform Building Codes.
WARNING: FAILURE TO USE MANUFAC-
TURE PROVIDED PARTS, VARIATIONS
IN TECHNIQUES AND CONSTRUCTION
MATERIALS OR PRACTICES OTHER THAN
THOSE DESCRIBED IN THIS MANUAL
MAY CREATE A FIRE HAZARD AND VOID
THE LIMITED WARRANTY.
Chimney
And
Termination
CCEK
W.H.I. Approved
(Required In
Canada)
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
When complete these fireplace systems con-
sists of five basic "sub-systems":
1. The Fireplace
2. The Chimney and Termination
3. The Optional Glass Doors
4. The Optional Combustion Air Kits
5. The Chimney Collar Enclosure Kit (Canada
Only) or Collar Duct Kit (U.S)
CLEARANCES AND HEIGHT
REQUIREMENTS
The fireplace may be placed on or near normal
construction materials*. The combustion air
kit, firestop spacer and roof flashings (not
chase flashings) may be placed directly on or
against normal construction materials*. The
chimney requires a minimum 2" (51 mm) air
space to combustibles ( See **Note ). A com-
bustible mantle may be installed 12" (305 mm)
above the opening of the fireplace as per NFPA
211, Section 7-3.3.3. In Canada the minimum
is 18" (457 mm) above the opening.
The fireplace and chimney system must be
enclosed when installed in or passing through
a living area where combustibles or people may
come in contact with it. This is important to
prevent possible personal injury or fire hazard.
For questions, please call your distributor or
the manufacturer. Special restrictions apply to
the front and facing of the fireplace and nearby
walls (See pages 16, 17 and 18 ).

CHIMNEY SYSTEM

These fireplaces are designed and code listed
for use with Security's FTF8 and FTF10 chim-
ney System only. Always use Security's FTF8
and FTF10 chimney components with these
fireplaces. Do not modify or alter these com-
ponents as this may cause a potential serious
hazard and void the Warranty.
*Construction Materials:
• framing materials • paneling
• particle board • flooring
• millboard • dry wall
• plywood • etc.
** Note: 1" (25 mm) when installed with FTF10
in the U.S. only.
3