Related Manuals for Fisher-Price 79006
Summary of Contents for Fisher-Price 79006
- Page 1 DELUXE SOOTHING BOUNCER SEAT Model Number: 79006, 79007 Please save these instructions for future reference. Adult assembly is required. Tool required for assembly: Phillips Screwdriver (not included). Requires one (LR20) alkaline battery (not included).
-
Page 2: Consumer Information
Usually, we can solve the problem over the telephone or send you replacement parts. Please call Fisher-Price® Consumer Affairs, toll-free at 1-800-432-KIDS, between 8 AM - 5 PM EST, Monday through Friday. - Page 3 PARTS Mirror 2 Paddles 3 Rings with Seatback Canopy Wire Footrest Wire Right Base Wire Base Connector Left Base Wire #8 - 32 x " #8 - 32 Nut - 2 Screw - 2 Shown Actual Size Shown Actual Size...
-
Page 4: Battery Installation
BATTERY INSTALLATION 1.5V – “D”, LR20 SHOWN ACTUAL SIZE Battery Compartment Door • Locate the soothing unit on the footrest wire. • Insert a coin into the battery compartment door and pry the battery compartment door off. • Insert one “D” (LR20) alkaline battery, as indicated inside the battery compartment. - Page 5 • Make sure both colored dots on the base wires are covered by the base connector. Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. ©2000 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
- Page 6 ASSEMBLY Colored Base Wire Footrest Colored Wire Base Wire Soothing Unit Base Connector Base • Position the footrest wire so that the Wire soothing unit is upright. Back View • While flexing the base wires toward each other, hook the footrest wire onto the ends of the base wires. •...
- Page 7 ASSEMBLY Seat Back Wire Toy Bar Socket Colored Plastic Cover Base Wire • Position the seat back wire with the toy bar sockets upright. • Fit the seat back wire completely onto the base wires, so that each end covers the colored dot on each base wire. •...
- Page 8 ASSEMBLY Pull Up Plastic Cover Protruding Side • Fit the nut (so that the protruding side is facing the seating area) into the hexagonal opening on the inside of #8 x 32 Nut each plastic cover. • Insert a screw through the outside of each plastic cover and tighten with a Phillips screwdriver.
- Page 9 ASSEMBLY Pad with Canopy Seat Back Wire Slot Restraint Belt • Position the pad with the canopy upright. • Fit the upper pocket on the back of the pad onto the seat back wire • Lift the foorest wire. Fit the lower pocket on the back of the pad onto the footrest wire .
- Page 10 ASSEMBLY Plastic Plastic Cover Cover Elastic Elastic Strap Strap • Wrap the elastic straps on the pad flaps around the outside of each Plastic plastic cover. Cover • Hook the elastic straps to the peg on the inside of each plastic cover. Elastic Strap Inside View...
- Page 11 ASSEMBLY Toy Bar Mirror Paddle Plugs Rings Sockets • Fit the toy bar plugs into the toy bar socket in each plastic cover. • Snap the mirror and the paddles to the toy bar. • The rings can be attached to the mirror and one of the paddles, as shown.
-
Page 12: Setup And Use
SET-UP & USE WARNING To prevent serious injury and/or falls: • Never use on any elevated surface. • Never use as a carrier or lift while child is seated. • Always use the restraint system. • Never leave child unattended. •... - Page 13 SET-UP & USE Anchored End Anchored End Buckle Buckle Free End Free End Tighten Loosen To tighten the restraint straps: • Feed the anchored end of the restraint strap up through the buckle to form a loop • Pull the free end of the restraint strap •...
- Page 14 SET-UP & USE Lift for Upright Lower for Recline Press Button Button Seat Back Adjustment The seat back can be adjusted upright or reclined for baby’s comfort. Reclined – Press the button on each plastic cover to lower the seat back. Hint: If your child is not seated in the seat, you will need to push the seat back at the same time you are pressing both buttons on the plastic covers.
- Page 15 SET-UP & USE Soothing Vibrations • Make sure your child is properly secured in the seat. • Slide the ON/OFF switch on the soothing unit to the ON position. The seat will vibrate. • Slide the ON/OFF switch on the soothing unit to the OFF position. The seat will not vibrate.
- Page 16 CARE The pad is machine washable. Wash the pad separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly. The frame, toy bar, mirror, paddles and rings may be wiped clean using a mild cleaning solution and a damp cloth.