Table of Contents
Advertisement
USER MANUAL
3.0 - OPERATING DESCRIPTION
3.1 - COMPLETE SYSTEM ARMING
Press the lock button on the vehicle original remote control
control
; system arming is confirmed by
a siren chirp if feature status has been configured and a flash
of the turn indicators
.
The system has a 30" pre-arming "neutral time" (indicated by the LED turned ON steady
3.2
If this function is configured, the system passively arms about 60" after ignition is switched off and after
the last door is opened and closed.
System activation is confirmed by the standard optical/acoustic signals.
Opening a door 60" before the system is armed causes the procedure to interrupt
temporarily; it will resume once the door is closed.
3.3 - ARMING INHIBIT TIME
System inhibit arming time lasts approximately 30"
exit the vehicle without triggering any alarm
3.4- SYSTEM ARMED
After the inhibit time the system is "armed" and ready to detect any theft attempt.
When the system is fully armed, the LED flashes.
3.5 - ALARM, INHIBIT TIME BETWEEN ALARMS AND ALARM CYCLES
A
ny theft attempt will trigger acoustic/optic signals.
At the end of an alarm cycle, before another one starts, there is a 5 sec. "neutral time".
Every alarm generates a maximum of ten 30" alarm cycles for each input and for each arming.
3.6 - SYSTEM DISARMING
Press the unlock button on the vehicle original remote control or press button "2" on the supplied
remote control; system disarming is confirmed by 2 siren chirps
and 2 flashes of the turn indicators.
An alarm condition is signalled by 5 acoustic signals (if feature status has been configured) and 5
flashes of the turn indicators.
Next paragraph
(3.7)
lists the various alarm causes and relative LED
3.7 - ALARM MEMORY
If, when disarming, the turn indicators flash 5 times and the alarm system gives 5 audio signals (if
feature status has been configured), it means that an alarm condition has occurred while away from
your vehicle. The cause of the last alarm can be identified by the LED memory.
Turn ignition key "ON"; the vehicle status LED blinks to indicate the last alarm cause.
The optical signals are repeated 3 times; to interrupt, turn ignition key "OFF".
The various alarm causes and relative optical signals are detailed in the following table.
PAGE 04 - USER MANUAL
or press button "1" on the supplied remote
(
- PA
SSIVE ARMING
during which time the LED lights up
.
(if feature status has been configured)
signals.
)
).
LED OFF (2 seconds)
We recommend replacing the default PIN-CODE, factory set as 1-1-1-1, with a custom PIN-CODE.
To do so, proceed as indicated in the example below, supposing the PIN CODE is 5-4-6-7.
;
it is possible to
If, while inserting the PIN-CODE, the LED flashes more than 9 times, the procedure will
!
With the system disarmed, press and hold the LED button.
!
Turn ignition key "ON" and wait at least 3 seconds before releasing the button.
!
A flash of the turn indicators and a low pitched signal indicate the system is in program mode; turn
ignition key to the "OFF" position.
!
After a 3 second pause, the status LED starts with the first sequence of 9 flashes.
!
th
At the 5 flash, which corresponds to PIN-CODE 1 digit (in this case, 5), press and release the
button on the status LED.
!
After another 3 second pause, the status LED starts with a new sequence of 9 flashes.
!
th
At the 4 flash, PIN-CODE 2 digit (4), press and release the button on the status LED.
!
After another 3 second pause, the status LED starts with a new sequence of 9 flashes.
!
th
At the 6 flash, PIN-CODE 3 digit (6), press and release the button on the status LED.
!
After a 3 second pause, the status LED starts with the last sequence of 9 flashes.
!
th
At the 7 flash, PIN-CODE 4 and last digit (7), press and release the button on the status LED.
!
There will be no audio/visual signals to in
LED FLASHES
Ignition attempt (+15/54)
Volumetric or external sensor
Wireless magnetic contacts and
Wireless infrared sensors (PIR)
LED ON (1 second)
4.0 - NEW PIN-CODE PROGRAMMING
be interrupted because of an invalid code number.
st
nd
rd
th
dicate the end of the procedure
ALARM
ALARM CAUSES
CYCLES
10
Door opening
10
Bonnet opening
10
10
Boot opening
10
10
opening detectors
10
.
USER MANUAL - PAGE 05
Advertisement
Table of Contents
