Table of Contents
Advertisement
2 – Features of the CC-222SL
1- Introduction
Insert a disc into the slot with the label side
Disc slot
k
uppermost. When the
Eject
disc is ejected from the slot.
MULTI DIAL
Used to select and confirm menu settings
l
etc. (turn to make the setting, push to confirm), and also
as a track search key when playing back discs.
REMOTE SENSOR window
;
signals from the remote control unit. Do not block this
window if you are using the remote control unit.
PITCH CONTROL knob
z
which allows the tape speed (and therefore the pitch) to
be changed by ±10%.
This three-position switch allows
REV MODE switch
x
the choice of single-side (
playback and recording, or continuous (
only (not recording).
DOLBY NR (OFF/ON) switch
c
Dolby noise reduction on and off for the cassette deck.
CD-TAPE CONT PLAY key
v
playback (alternating between disc and cassette) on and off.
Rear panel
DIGITAL COA XIAL (INPUT and OUTPUT ) jacks
@
These RCA jacks input and output SPDIF digital audio
data to and from the disc recorder.
Digital audio data received can be at any sampling
frequency between 32kHz and 48kHz. The output is
always 44.1kHz.
DIGITAL OPTICAL (INPUT and OUTPUT) jacks
#
TOSLINK-compatible connectors input and output
SPDIF digital audio data to and from the disc recorder.
Digital audio data received can be at any sampling fre-
quency between 32kHz and 48kHz.
LINE OUTPUTS (L,R) / 1(CD), 2(TAPE/AUTO)
$
these connectors to connect the amplifier to the analog
outputs of the disc recorder (1) or the outputs of the cas-
sette deck (2).
RIA A PHONO INPUT (L , R) a nd G ND ter mina l
%
Use these connectors to connect a record deck to the
CC-222SL. The destination of the signal is determined
by a menu item.
1
TASCAM CC-222SL
key is pressed, the loaded
Receives the infrared
This is a centerdetented knob
) or bidirectional (
Ä
Ê
) playback
ä
Use this switch to turn the
Use this to turn continuous
@
#
$
These
Use
CD TIMER (OFF/PLAY) switch
b
the CD timer option on or off. When this is in the
position, turning on the machine with a disc inserted
will automatically start playback.
CD STOP key
Stops CD playback or disc recording.
n
CD PLAY key
m
record standby mode).
CD PAUSE key
,
recording (starts recording from record standby mode).
CD RECORD key
.
mode and performs manual track incrementing while
recording.
MONITOR ( TAPE,MIX,DISC) switch
/
)
selects the source for the headphone outputs as either the
cassette deck, the disc recorder, or a mixture of both.
PHONES jack and volume control
!
pair of stereo headphones to this 1/4" jack, and adjust
the level with the control.
%
^
Connect the earth (grounding) wire of the record deck
to the
GND
terminal.
NOTE
Do not connect a record deck to the
do not connect any other equipment to these jacks.
LINE INPUTS (L,R) / 1(CD), 2(TAPE)
^
nectors to connect signal sources to the analog inputs
of the disc recorder (1) or the inputs of the cassette deck
(2).
AC IN jacks
Connects the power cable supplied.
&
VOLTAGE SELECTOR switch
*
either
230 V
or
120 V
NOTE
The voltage selector is only available on units for North
American market.
Use this switch to turn
Starts CD playback or recording (from
Pauses or resumes CD playback or
Places the disc in record standby
This switch
Connect a standard
&
inputs and
L I NE
Use these con-
Switches the voltage to
.
PLAY
Advertisement
Table of Contents
