Tprocedure 11 - Retention Strap/Retainer; Replacing Battery Box Retainer/Retainer Clip - Group 24 Battery Base Frames - Invacare Storm Series Service Manual

RETENTION STRAP/RETAINER
This Procedure Includes the Following:
Replacing Battery Box Retainer Bar/ Retainer Clip
-Group 24 Battery Base Frames
WARNING
After ANY adjustments, repair or service and BE-
FORE use, make sure that all attaching hardware
is tightened securely - otherwise injury or dam-
age may result.
REPLACING BATTERY BOX
RETAINER BAR/RETAINER CLIP -
GROUP 24 BATTERY BASE FRAMES
(FIGURE 1)
1. Remove the battery box. Refer to INSTALLING/RE-
MOVING GROUP 24 BATTERY BOXES in PROCE-
DURE 9 of this manual.
Replacing Retainer Clip
1. Perform one (1) the following:
A. RWD AND MWD MODELS - Remove the
mounting screw that secures the retainer clip and
shock (or rubber element) to the base frame.
B. FWD MODEL - Remove the mounting screw,
washer, spacer, and locknut that secure the re-
tainer clip to the battery box sub-frame.
2. Remove the existing retainer clip.
3. Perform one (1) the following:
A. RWD AND MWD MODELS - Position the NEW
retainer clip between the shock (or rubber ele-
ment) and the battery box sub-frame as shown
in FIGURE 1. Make sure the angled end of the
retainer clip is facing up.
B. FWD MODEL - Position the NEW retainer clip
between the spacer and the battery box sub-
frame as shown in FIGURE 1. Make sure the
angled end of the retainer clip is facing upwards.
WARNING
The Battery Box Retainer Bar/Retainer Clip MUST
be fastened securely in place before using the
wheelchair. Use Loctite 242 and torque to 160-
inch pounds.
4. Perform one (1) the following:
A. RWD AND MWD MODELS -Reinstall the mount-
ing screw that secures the retainer clip and shock
(or rubber element) to the base frame. Use Loctite
242 and torque to 160-inch pounds.
All manuals and user guides at all-guides.com
5. Reinstall the battery boxes. Refer to INSTALLING/RE-
Replacing Retainer Bar
1. Perform one (1) the following:
2. Pull up on the battery box retainer bar to remove it from
3. Install the two (2) existing spacers through the mounting
4. Perform one (1) the following:
5. Perform one (1) the following:
6. Reinstall the both battery boxes. Refer to INSTALLING/
53
B. FWD MODEL - Reinstall the mounting screw,
washer, spacer, and locknut that secure the retainer
clip to the battery box sub-frame. Use Loctite 242
and torque to 160-inch pounds.
MOVING BATTERY BOXES - GROUP 24 BATTERY
BASE FRAMES in PROCEDURE 9 of this manual.
A. RWD AND MWD MODELS -Remove the two (2)
mounting screws and spacers that secure the bat-
tery box retainer bar to the base frame.
B. FWD MODELS - Remove the two (2) mounting
screws, spacers, washers, and locknuts that se-
cure the retainer bar to the battery box sub-frame.
the base frame.
holes in the NEW battery box retainer bar.
WARNING
The Battery Box Retainer Bar/Retainer Clip MUST be
fastened securely in place before using the wheel-
chair. Use Loctite 242 and torque to 160-inch
pounds.
A. RWD AND MWD MODELS - Line up the NEW
battery box retainer bar and spacers with the mount-
ing holes in the battery box sub frame and the base
frame.
B. FWD MODELS - Line up the NEW battery box
retainer bar and spacers with the mounting holes in
the battery box sub frame.
A. RWD AND MWD MODELS - Reinstall the mount-
ing screws that secure the battery box retainer bar
between battery box sub frame and the base frame.
Use Loctite 242 and torque to 160-inch pounds.
B. FWD MODELS - Reinstall the mounting screws
that secure the battery box retainer bar onto battery
box sub frame. Use Loctite 242 and torque to 160-
inch pounds.
REMOVING GROUP 24 BATTERY BOXES in PRO-
CEDURE 9 of this manual.
PROCEDURE 11
R
E
E
N
O
N
S
R
A
P
R
E
A
N
E
R
T
T
I
T
T
I