IVT GTE-1000 Manual page 9

∙
The tool must be assembled correctly before use.
∙ Only use the tool for its designed purposes.
∙
On the tool, there may be also decals and further
indications about the safety equipment to use that must
be considered. The prevention of accidents is dependent
upon the awareness, common sense and proper
training of everyone involved in the operation, transport,
maintenance and storage of the tool.
∙ Never leave the tool unattended.
∙ Never allow children to use the tool. Children should
be supervised to ensure that they do not play with the tool.
∙ Keep children and pets away. All onlookers should
be kept at a safe distance away from the tool when it is
in use.
∙ The user is responsible for third parties while
working with the tool.
∙ People who aren't acquainted with the operating
instructions, children, juveniles who have not yet reached
the minimum age for using this tool and people under the
influence of alcohol, drugs or medication are not allowed
to use the tool. Local regulations may restrict the age of
the operator.
WARNING!
alcohol, medication and drugs, plus
states of illness, fever and fatigue will
affect your ability to react. Do not use
this tool in any of these situations.
∙ Make sure that all the protective devices (if present)
are fitted and are in good condition.
∙
Never operate the tool with defective safety devices
or guards (if present), or without safety devices in place.
∙
Inspect the entire tool to look for loose parts (e.g.
nuts, bolts, screws, etc.) and for any damage. Check
at frequent intervals if screws and bolts (if present) are
properly tight to be sure the equipment is in safe working
condition. Repair or replace them, if necessary, before
using the tool. Serious injury to the operator and to the
bystanders could result if there's any damage to the tool.
∙ While using the tool, dress properly. Do not
wear loose clothing or jewelery that could become
caught by the tool. Wear suitable working clothes. It is
recommended that legs and feet are covered, to protect
them from eventual flying debris. Do not work barefoot
or wearing open sandals. Long air should be tided back.
∙
Keep handles and grips dry, clean and free from oil
and grease.
∙ Use proper protective equipment. Use safety
glasses and safety gloves. Also use a dust mask during
pulverulent operations or if exhaust gases are present.
When necessary, use also non-slipping boots or shoes,
hardhat and earplugs. If the noise level exceeds 85
dB(A), ear protection is obligatory.
The consumption of
WARNING! Use personal protective
equipment!
personal
protect your own health and the
health of others and ensure a trouble-
free operation of the tool.
∙ Do not start to use the tool if it is in an inverted
position or it is not in the right working order.
∙ Ensure that you have a good stand, while you
operate with the tool. Keep proper footing and balance
at all times.
∙ Keep work area clean. Cluttered areas invite
injuries. Before use, all foreign bodies must be removed
from the working area, also pay attention to foreign
objects during operation.
∙
Do not force the tool.
∙ Only work in daylight or sufficiently good artificial
light. Never operate the tool without good visibility.
∙ Be careful not to drop the tool or hit it against
obstacles.
ATTENTION! Stay alert. Watch what you are doing.
Distraction can cause you to lose control. Use
common sense.
Electrical safety rules
ATTENTION! When using electrical tools, the
following safety instructions should be observed to
prevent the risk of electric shock, personal injury
and fire. Read and observe these instructions
carefully before using the tool.
∙
It is recommended for increased electrical safety
to use a Residual Current Device (RCD) with a tripping
current of not more than 30 mA. Always check your RCD
every time you use it. Consult a reliable electrician.
WARNING! The use of an RCD or
other circuit breaker unit does not
release the operator from the safety
instructions
practices given in this manual.
∙
The main voltage must correspond to the one
marked on the labels and on this manual. Do not use
other sources of power.
∙ Before inserting the plug in the main socket, make
sure that the socket ratings are correct and correspond
to those indicated on the rating label on the appliance.
∙ Avoid body contact with grounded surfaces such
as pipes, radiators, ranges and refrigerators. This
9
Instruction manual
Safety devices and
protective equipment
and safe working
EN