Advertisement
S –1000 Front Panel and Remote Functions
INDIVIDUALIZED
CHANNEL TRIM
The center, surr/back, and sub
buttons or keys make temporary
loudspeaker output adjustments
of +/- 10 dB. These temporary
adjustments revert to 0 dB when
a new device is selected or when
the system is powered down.
21 Center Button/Key
Adjusts the center loudspeak-
er volume. Press the center
button or key, then use the
volume knob or up and down
directional keys to make the
adjustments.
Phantom Center. Press the
center button or key twice
activate. Press the center but-
ton twice again to deactivate.
22 Surr/Back Button/
Rear Key
Adjusts the volume of the sur-
round and back loudspeakers.
Press the surr/back button,
then use the volume knob or
up and down direction keys to
adjust the surround loud-
speakers. To adjust the back
loudspeakers, press the surr/
back button.
SURROUND TRIM
Figure 2 The S–1000 Remote
28
1
33
32
24
21
5
6
10
11
19
16
15
17
Krell S–1000
appears on the front panel
display. Press the surr/back
button again.
appears
BACK
on the front panel display.
Then use the volume knob or
the up and down directional
keys to adjust the volume of
the back loudspeakers.
23 Sub Button/Key
Adjusts the subwoofer vol-
ume. Press the sub button or
key, then use the volume
knob or the up and down
directional keys to adjust the
subwoofer volume.
24 Balance Button/Key
Adjusts the main left/right
loudspeaker balance. Press
the balance button or key,
then use the volume knob or
the up and down directional
keys to adjust the balance.
Balance levels show numeri-
cally on the front panel dis-
play. Balance may be adjust-
ed in .5 dB increments, up to
6 dB. The center position is
displayed as BAL 0.
Balance level keys revert to
their original function as vol-
ume level controls after 3
seconds of inactivity.
29
30
31
23
22
9
7
13
12
14
8
18
continued
PROCESSOR
FUNCTIONS
25 Save Button/Key
Saves system configuration
settings. Press and hold this
button or key to activate. This
function is also used to pro-
gram a learning remote.
26 Volume Knob/Keys
Scrolls through menu selec-
tions, adjust output for the
entire system, and adjusts
volume and balance levels
for the center loudspeaker,
surround/back loudspeakers,
and subwoofer. Volume and
balance levels appear in the
front panel display.
27 Recall Button
Recalls previously stored sys-
tem configuration settings.
Returns configuration settings
to factory default: With the
S–1000 in the operational
mode, hold the recall button
and press the power button.
REMOTE ONLY
FUNCTIONS
28 Amp Key (Power Amp Key)
Operates IR controllable
power amplifiers, such as all
Krell Evolution amplifiers.
REMOTE ONLY
FUNCTIONS
28 Amp Key
29 Menu Key
30 Prev Key
31 Mute Key
32 Enter Key
33 Right Directional Key
All other functions on the
remote control duplicate front
panel functions.
The following keys are not
active on the S–1000 remote:
MAIN, Z2, THX
Note:
6 The LD key on the remote
activates the cable device
button (6) on the front panel.
29 Menu Key
Accesses the setup menu
and on-screen menu display.
30 Prev Key
Return to the previously dis-
played setup menu screen.
31 Mute Key
Mutes the S–1000 output.
When this function is active,
appears in the
VOLUME MUTE
front panel display.
32 Enter Key
Accepts setup menu selec-
tions, accept an input device
selection, or displays current
system conditions.
33 Directional Keys
Up and Down Directional
Keys. Adjust volume, and
adjust balance if the balance
function is activated.
In the operational mode, the
up and down directional keys
select EQ memory.
Right Directional Key. In the
operational mode, the right
arrow key engages Digital
Room EQ.
All Directional Keys. In the
setup menu, all four directional
keys navigate the on-screen
menus.
HOW TO NAVIGATE
THE SETUP MENU
1 Press the menu key (29) to
enter and exit the setup
menu.
2 Press the direction keys (33)
to scroll from line to line,
and to scroll through options
within a line.
3 Press the enter key (32) to
select a line and set an
option.
4 Press the prev key (30) to
return to the previous screen.
5 Press the pre key (1) to exit
the setup menu; the S–1000
reverts to stand-by.
3
Advertisement
