Advertisement
Figure 1 The S –1000 Front Panel
6
5
7
DVD
SAT
CD
TUNER
AUX
10
11
12
POWER
2
1
3
4
FRONT PANEL
AND REMOTE
FUNCTIONS
BASIC
OPERATION
1 Power Button/Pre Key
Switches the S–1000 from
stand-by to operational mode,
and to switch the 12 VDC out-
put (12 V trigger) on and off.
2 Power/Stand-by LED
Stand-by Mode. When the
AC power cord is plugged
into the wall, the LED illumi-
nates in red: the S–1000 is in
stand-by mode.
Operational Mode. When the
power/stand-by button is
pressed, the LED illuminates
in blue: the S–1000 is in the
operational mode.
3 Infrared Sensor
Receives commands from the
S–1000 remote control.
4 Infrared Emitter
Sends the S–1000 remote
operation code to a learning
remote.
2
8
9
21
24
VCR
TV
BALANCE
GAME
TAPE/VCR2
CENTER
RECALL
SURR/BACK
SAVE
SUB
13
27
25
14
22
23
INPUT DEVICE
SELECTION
The S–1000 is equipped with ten
input device selection buttons on
the front panel and corresponding
keys on the remote control. If
properly configured, the S–1000
automatically engages the cor-
rect video and audio inputs when
you press the device selection
button.
5 DVD Button/LED/Key
6 Cable Button/LED/Key
7 SAT Button/LED/Key
8 VCR Button/LED/Key
9 TV Button/LED/Key
10 CD Button/LED/Key
11 Tuner Button/LED/Key
12 Aux Button/LED
and Aux 1 Key
Selects an auxiliary device:
phono, tape, or an additional
DVD, LD, CD, or VCR.
13 Game Button/LED
and Aux 2 Key
14 Tape/VCR2 Button/LED/Key
Playsback pre-recorded
tapes, and compares the out-
put signal of an analog tape
recorder to an audio source.
PROCESSING
MODE
15 Stereo Button/LED/Key
Selects stereo decoding.The
red LED illuminates when this
function is engaged.
PRE AMP
26
19
16 Mode 1 Button/LED/Key
17 Mode 2 Button/LED/Key
Selects available processing
modes (such as Dolby Digital,
DTS, PLII Movie, etc.) for
incoming signals from an
audio source.
The default mode for a signal
is always stored in Mode 1.
Use the Mode 1 button or key
to select the default mode. All
modes that can be used for
the same signal are automati-
cally stored in Mode 2. Use
the Mode 2 button or key to
scroll through these other
modes. The last mode dis-
played in Mode 2 is the se-
lected mode. Based on the
source signal, the S–1000
automatically selects the
assigned mode for the avail-
able signal.
18 Pro Logic II
Button/LED/Key
Selects Dolby Pro Logic II
modes for Dolby Surround
encoded material, including
laser discs, videotapes, televi-
sion broadcasts, and com-
pact discs. The red LED illu-
minates when Dolby Pro
Logic II decoding is selected.
20
STEREO
MODE 1
MODE 2
PRO LOGIC II
15
16
17
18
Note: These modes are
selected automatically if
Dolby Digital source material
is encoded for Pro Logic. To
turn off these modes, press
the Pro Logic II button.
19 Preamp Button/LED/Key
Sends the signal from an ana-
log input directly to the vol-
ume control, with no digital
processing, using the analog
stage of the preamplifier.
This avoids possible digital
signal degradation. Used for
components with a high qual-
ity signal, such as the Krell
Evolution 505 CD Player.
Note: This feature is available
with a signal from an analog
input. If you attempt to use it
with a signal from a digital
input, the OSD reads
ALLOWED
DISPLAY
WINDOW
20 Front Panel Display
Provides status messages for
S-1000 operations, including
volume and balance level,
decoding mode, and zone
information. When a new
device is selected, the physi-
cal inputs are displayed. The
display turns off after 60 sec-
onds of inactivity.
Krell S–1000
NOT
Advertisement
