Preparation For First Time Usage; Turn On The Unit For The First Time; Clock Set Up - Sylvania CDVC90DP Owner's Manual

Preparation for First Time Usage

Turn on the unit for the first
time
VCR VCR
VCR VCR VCR
1
1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see"RF Output Channel" section.
2
2
POWER
TV Screen
LANGUAGE SELECT
B ENGLISH
FRANÇAIS
or
ESPAÑOL
3
3
AUTO SET UP
Do you connect the cable from the cable box or
the satellite box to the DVD/VCR's ANT IN jack?
YES
Y es
Y es
Press the MENU
button to exit
• Refer to "Tips for Cable Box
or Satellite Box" section on
page 6.
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memo-
rized in this unit by using the CHANNEL
buttons.
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press the B button once again.
Tips
Tips
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
To Select a Channel
You can select a channel by directly
entering channel using the Number but-
tons on the remote control.
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, press 1,1,7)
• You must precede single-digit channel
numbers with a zero (For example:
02, 03, 04 and so on).
To Preset the Channel Again
1) Press the MENU button until the main
menu appears.
2) Select "CHANNEL SET UP" by pressing
the K or L button. Then, press the B but-
ton.
3) Select "AUTO SET UP" by pressing the
K or L button. Then, press the B button.
After scanning, the tuner stops on the low-
est memorized channel.
To Change the On-Screen Language
1) Press the MENU button until the main
menu appears.
2) Select "LANGUAGE SELECT" by press-
ing the K or L button. Then, press the B
button.
3) Select "ENGLISH" , "FRANÇAIS" or
[ON]
"ESPAÑOL" by pressing the K or L but-
ton. Then, press the CLEAR/C.RESET
button.
Tips
Tips
• If you accidentally select Spanish or
French and need English: Press the
MENU button and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press
the B button, and select ENGLISH. Finally,
CH 01
press the CLEAR/C.RESET button.

Clock Set Up

VCR VCR
VCR VCR VCR
1
1
MENU
or
NO
2
2
or
3
3
or
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
• If the clock is not set, the
CLOCK SET screen
appears when you press
the MENU button. In this
case, go to step [2].
CLOCK SET
MONTH DAY YEAR
0 3 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 – – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current day
– 10 –
4
4
CLOCK SET
MONTH DAY
0 3 / 1 5
or
HOUR MINUTE
– – : – –
Select the current year
5
5
CLOCK SET
MONTH DAY
0 3 / 1 5 MON 2 0 0 4
or
HOUR MINUTE
0 5 : – –
Select the current hour
6
6
CLOCK SET
MONTH DAY
0 3 / 1 5 MON 2 0 0 4
or
HOUR MINUTE
0 5 : 4 0
Select the current minute
7
7
CLOCK SET
MONTH DAY
0 3 / 1 5 MON 2 0 0 4
or
HOUR MINUTE
0 5 : 4 0
Select "AM" or "PM"
8
8
To exit the CLOCK SET
screen.
Tips
Tips
• To go back one step, press the s button
(during the steps [2] to [7].)
• Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
YEAR
2 0 0 4
AM/PM
– –
YEAR
AM/PM
– –
YEAR
AM/PM
– –
YEAR
AM/PM
P M AM
B PM
EN