Sylvania DVR90DG Owner's Manual page 31

7
Press [ENTER] when
information is entered. Your
program setting will be stored.
• To set another program, repeat
steps 2 to 7.
• To exit, press [TIMER PROG.]
or [SETUP].
• When two or more programs are
overlapped, "Overlap" and the
overlapped program number will
appear in the display.
Checking, canceling, or correcting the timer programming
information
1
Press [POWER].
indicator disappears from the
front panel display.
2
Press [TIMER PROG.].
Timer Programming list will appear.
Timer Programming
Date Start End CH
1. JAN/01 12:57AM 1:57AM CH8
2. ---
3. ---
3
4. ---
5. ---
Check the information on the
6. ---
7. ---
list you will need.
8. ---
To stop the Timer Recording in process
Press [STOP C] on the front panel of the unit.
[STOP C] on the remote control is not effective.
If the timer program did not complete correctly, the error number
appears in the Timer Programming list.
Timer Programming
Date Start End CH
*
JAN/01 12:57AM 1:57AM CH8
2. ---
3. ---
4. ---
5. ---
6. ---
7. ---
8. ---
Press [CLEAR] to erase the
selected program.
• A program with the error number is grayed and asterisked in the Timer Programming list.
• Once the Timer Programming list with error line(s) is displayed, or after canceling and setting again the timer
standby mode, the program line(s) with error will be cleared.
Recording
Timer Recording (cont'd)
8
Press [POWER] to turn off.
indicator will appear on the
front panel display.
4
To clear the timer programming:
Using [K / L], select your
desired program. Press
[CLEAR].
To correct the timer program-
ming:
Using [K / L], select your desired
program. Press [ENTER].
Speed
Next, correct the timer programming
1H
by using [K / L / { / B].
Finally, Press [ENTER] again.
5
Press [TIMER PROG.] to exit.
6
Press [POWER] to return to the
timer standby mode.
Each error number means:
E1-22 Recording error other than
Speed
E37-39 below
E22
E23-24 Unrecordable disc
E25-28 Copy prohibited program
E29 Disc protected
E30 Disc full
E31-32 Already 99 titles recorded
E33 Already 999 chapters
recorded
E34 No space for Control
information
POWER OPEN/CLOSE
8 TIMER
ZOOM PROG.
A
.@/: ABC DEF
1 2 3
CH
GHI JKL MNO
4 5 6
PQRS TUV WXYZ
REPEAT
7 8 9
DISPLAY SPACE CLEAR SETUP
0
T OP MENU MENU/LIST RETURN ENTER
K
{ B
L
AY
REC SPEED REV PL FWD
h B g
POWER OPEN/CLOSE
1 TIMER
SKIP PAUSE SKIP
Bx1.3/0.8
ZOOM PROG.
A
H F G
STOP CM SKIP
REC/OTR
6 .@/: ABC DEF
C
1 2 3
CH
GHI JKL MNO
4 5 6
PQRS TUV WXYZ
REPEAT
7 8 9
DISPLAY SPACE CLEAR SETUP
0
T OP MENU MENU/LIST RETURN ENTER
K
{ B
L
AY
REC SPEED REV PL FWD
h B g
SKIP PAUSE SKIP
Bx1.3/0.8
Note
H F G
STOP CM SKIP
REC/OTR
• Press [TIMER PROG.] to
C
check the timer programming
in process.
When the Timer Recording is
proceeding, that program will
be highlighted in red.
E35 PCA full
E36 Already finalized Video
format disc
E40 Some portion has not
been recorded because
of program overlapping.
Recording did not start at
the start time.
E41 Power failed
E42 No disc when recording
7
2
5
4
31