Page 1
Brought to You by Augusta Flint 10” BENCH TABLE SAW - 2 HP Model 45804 ASSEMBLY AND OPERATING INFORMATION ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com TO PREVENT SERIOuS INjuRY, READ AND uNDERSTAND ALL WARNINGS AND INSTRuCTIONS BEFORE uSE.
Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. SAVE THESE INSTRuCTIONS WORK AREA Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. SKU 45804 PAGE 2 REV 07j...
Stay alert. Watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. SKU 45804 PAGE 3...
Page 4
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. SKU 45804 PAGE 4...
The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See Figure A.) SKU 45804 PAGE 5...
Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) FIGuRE B SKU 45804 PAGE 6...
Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. FIGuRE C SKU 45804 PAGE 7...
Turn off the Table Saw if the woodstock is to be backed out of an uncompleted cut. Always feed the woodstock into the Saw Blade and against its rotation. Make sure the woodstock is supported at all times while sawing. Use a Roller Stand (not provided) with larger woodstocks if necessary. SKU 45804 PAGE 8...
Page 9
Do not operate the Table Saw if the Guard Assembly does not move freely and close instantly. Before each use, raise the Guard Assembly and make sure it moves freely and does not touch the Saw Blade or any other part, in all angles and depths of cut. SKU 45804 PAGE 9...
Page 10
Note: While unpacking and before attempting assembly; loosen the motor, remove the two styrofoam inserts that hold the motor in place during packing, and retighten the motor. SKU 45804 PAGE 10...
Page 12
Washer (64), and Big Washer (61) over the Socket Head Screw (63) and thread into the end of the mounting post. Use the included 4 mm Hex Wrench (196) to tighten the Socket Head Screw (63). See Figure H. FIGuRE H SKU 45804 PAGE 12...
Fence Assembly all the way onto the Table (105). Then, lock the Fence Assembly in position by lowering the Fence Handle to a vertical position. FIGuRE K (See Figure L) BLADE GUARD ASSY. (50) FENCE ASSY. (75) FENCE HANDLE (80) (UNLOCKED POSITION) FIGuRE L SKU 45804 PAGE 13...
Page 14
To Adjust The Angle Of The Saw Blade: The Table Saw is capable of making cuts from 90 degrees to 45 degrees. The Table Saw also features an Angle Scale and Angle Indicator on the front side of the unit. (See Figure M.) SKU 45804 PAGE 14...
Page 15
(37), pushes the workpiece toward the turning Saw Blade (3). (See Figure O.) After the cut is under way the right hand, with the aid of the Push Stick (37), continues pushing the workpiece forward. Just before the cut is near completion SKU 45804 PAGE 15...
Saw Blade (3), broken parts and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, turn off the Table Saw immediately and have the problem corrected before further use. Do not use damaged equipment. SKU 45804 PAGE 16...
AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 45804 PAGE 17...
Page 18
Open-end Spanner Press Spring Assembly of Miter Guide Clamp Lock Angle Ruler Body Ruler Round Pin Screw Plane Washer Lock Washer Angle Ruler Body Front Board Screw Spring Pin Spring Washer Angle Ruler Finger SKU 45804 PAGE 18 REV 04j...
Page 20
Brought to You by Augusta Flint Assembly Diagram A (Parts 1-95) SKU 45804 PAGE 20...
Page 21
Assembly Diagram B (Parts 96-192) Note: Part 193-Mounting Plate- not shown. Part 194,195, and 196-Hex Wrenches- not shown. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 45804 PAGE 21...
2” Assemble Push Block ” with glue and wood screws WARNING! (see warning to the right). When using wood screws, lo- cate the screws so they will not accidently come in contact with the saw blade. SKU 45804 PAGE 22...
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 REV 07j SKU 45804 PAGE 23...