Using The 2-Led Area Light; Care And Maintenance; Battery Replacement; Safe Battery Disposal - Stanley AirPro 120 HRC120DS Instruction Manual

4. Press the Power Button to turn the unit on. The backlit LCD Screen will display the following, indicating the unit is in Standby Mode:
The digital display will alternately show the flashing pre-set PSI value (that was last set by the Pressure Control Buttons) for 2 seconds;
then it will flash the current pressure of the item being inflated for 5 seconds (which will then light solid).
IMPORTANT: If no other actions are taken after pressing the Power Button, the unit will automatically shut off after one minute of inactivity.
5. Follow either steps 4 through 6 in the "Inflating Tires or Products With Valve Stems at Auto Mode" section or steps 4 through 5 in the
"Inflating Tires or Products With Valve Stems at Manual Mode" section.
IMPORTANT NOTE: Small items such as volleyballs, footballs, etc. inflate very rapidly. Do not over-inflate.
6. Disconnect the nozzle adapter from the inflated item.
7. Unscrew and remove the nozzle adapter from the SureFit
CAUTION: TO REDUCE THE RISK PROPERTY DAMAGE:
• Always allow the unit to cool before storing it.
• To prevent hose damage, secure the compressor hose and SureFit
• Recharge the unit fully after each use.

USING THE 2-LED AREA LIGHT

The Area Light is controlled by the Compressor. When the Compressor is turned on, the Area Light is activated. When the Compressor is
tuned off, the Area Light turns off. Press the Power Button (refer to the "Features" section to locate) to turn the Compressor and Area
Light on. Press the Power Button and hold for one second to turn the unit off. Make sure the Power Button is turned off when the unit is
being recharged or stored.

CARE AND MAINTENANCE

All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we
recommend that the battery is charged at least every 30 days.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the unit with a soft cloth moistened with a mild
solution of water and detergent.
There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and wires. Contact manufacturer to replace
any components that have become worn or broken.
Battery replacement/disposal

BATTERY REPLACEMENT

The battery should last the service life of the unit. Service life is dependent on a number of factors including but not limited to the
number of recharge cycles, and proper care and maintenance of the battery by the end user. Contact manufacturer for any information
you may need.

SAFE BATTERY DISPOSAL

Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly. Recycling is
required. Failure to comply with local, state and federal regulations can result in fines, or imprisonment.
Please recycle.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in
injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
12V DC Charging Adapter Fuse Replacement
The fuse in the plug end of the 12V DC Charging Adapter protects the adapter's charging circuit. If the 120V AC Charging Adapter
operates, but the 12V DC Charging Adapter does not, then this fuse may be opened (blown).
TO REPLACE THE FUSE:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate a replacement 12 amp fuse.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.
7. Test for proper operation of the 12V DC Charging Adapter.
nozzle.
®
nozzle using the Storage Clips after each use.
®
8