Related Manuals for Health O Meter PELSTARONE
Summary of Contents for Health O Meter PELSTARONE
- Page 1 PELSTARONE External Wireless Kit USER INSTRUCTIONS PELSTAR, LLC 9500 West 55th St. McCook, IL 60525-7110 USA www.homscales.com © Pelstar, LLC 2018 P/N UMPELSTARONE_REV20181220...
-
Page 2: Table Of Contents
® Thank you for purchasing this Health o meter Professional product. Please read this manual carefully and keep it for easy reference or training. TABLE OF CONTENTS PRODUCT OVERVIEW........................ 3 PACKAGE CONTENTS........................ 4 HARDWARE INSTALLATION - STEP 1 ..................5 HARDWARE INSTALLATION - STEP 2 ( ).......... -
Page 3: Product Overview
EMR, the EMR installed on the user’s PC must be included on the list of Welch Allyn ® EMR partners. Visit www.welchallyn.com to view a complete list of EMR partners. Health o meter Professional scales are preconfigured to interface with the following Welch Allyn ®... -
Page 4: Package Contents
PACKAGE CONTENTS ® Hardware to Connect to Health o meter Professional Scale: HOMBT1 Scale Unit (Blue Box with Yellow Label) USB Wall Power Adapter (Note: color of power adapter may vary) RS232 Wireless Adapter POWER CABLE (6 ft. USB cable) SCALE CABLE (1 ft. -
Page 5: Hardware Installation - Step 1
HARDWARE INSTALLATION - Step 1 ® 1. Using the SCALE CABLE (1 ft. USB cable), connect the Health o meter Professional scale USB port to the “TO SCALE” USB port on the HOMBT1 Scale Unit as shown below. 2. Connect POWER CABLE (6 ft. USB cable) to USB Wall Power Adapter, and then connect other end to the HOMBT1 Scale Unit “Power In”... - Page 6 HARDWARE INSTALLATION - Step 2 The PELSTARONE External Wireless Kit allows for the scale to interface wirelessly with Welch Allyn ® ® ® Connex Spot Monitors, Connex Vital Signs Monitors, and Connex Integrated Wall Systems. Users ® ® can also connect wirelessly to a Windows PC to interface with Allscripts TouchWorks Professional™, Midmark...
-
Page 7: Hardware Installation - Step 2 ( For Connex Monitors )
® HARDWARE INSTALLATION - Step 2 for Connex Monitors ® ® The following instructions illustrate the hardware set up for connecting to a Welch Allyn Connex Vital Signs Monitor (CVSM). USB ports on the Connex Spot and Integrated Wall Systems are located on the underside of the monitor. - Page 8 HARDWARE/DRIVER INSTALLATION (for Scale Communication ® to a Windows 1. Download the CP210x USB to UART Bridge VCP Driver using one of the following methods: a. Go to http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx and search for “CP2102 Driver Download”. Go to http://www.silabs.com/ ® XP/Server 2003/Vista/7/8/8.1/10 (6.7) – Version 6.7 2.
- Page 9 HARDWARE/DRIVER INSTALLATION (for Scale Communication ® PC) – (Cont.) to a Windows Accept the license agreement and click “Next” Please wait while the driver installs. P/N UMPELSTARONE_REV20181220...
- Page 10 HARDWARE/DRIVER INSTALLATION (for Scale Communication ® PC) – (Cont.) to a Windows When driver installation is complete click “Finish” to close the installation Wizard. ® 4. Connect the USB wireless dongle to any available USB 2.0 port on the Windows P/N UMPELSTARONE_REV20181220...
- Page 11 Hardware/Driver Installation (for Scale Communication to a ® PC) – (Cont.) Windows ® “Device Manager” and check that the USB wireless dongle was 5. Open Windows ® recognized by the Windows 6. Once the driver installation is complete, the USB wireless dongle will automatically connect to the scale and will be ready to receive data.
-
Page 12: Wireless Communication - Step 3
WIRELESS COMMUNICATION - Step 3 NOTE: THE SERIAL NUMBER ON THE USB WIRELESS DONGLE MUST MATCH THE SERIAL NUMBER ON THE YELLOW LABEL OF THE HOMBT1 SCALE UNIT TO ENABLE ACTIVE WIRELESS COMMUNICATION. 1. Power on the scale and either the Welch Allyn monitor or PC. To check that the HOMBT1 scale unit has established wireless communication, observe that the status LEDs are illuminated as in the figure below. -
Page 13: Troubleshooting
TROUBLESHOOTING NOTE: THE SERIAL NUMBER ON THE USB WIRELESS DONGLE MUST MATCH THE SERIAL NUMBER ON THE YELLOW LABEL OF THE HOMBT1 SCALE UNIT TO ENABLE ACTIVE WIRELESS COMMUNICATION. HOMBT1 SCALE UNIT USB WIRELESS DONGLE SERIAL NUMBERS MUST MATCH TO ENABLE WIRELESS COMMUNICATION. - Page 14 HOMBT1 Scale Unit matches the Serial Number on USB Wireless Serial Number on the USB Wireless Dongle. Dongle does not match Serial If they do not match contact Health o meter Number on HOMBT1 Scale Unit Professional Customer Service at 1-800- 815-6615.
-
Page 15: Warranty
® Health o meter Professional products are manufactured, designed, and owned by Pelstar, LLC. ® We reserve the right to improve, enhance, or modify Health o meter Professional product features or specifications without notice. © Pelstar, LLC 2018 P/N UMPELSTARONE_REV20181220... -
Page 16: Regulatory Information
REGULATORY INFORMATION RS232 Wireless Adapter RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. - Page 17 REGULATORY INFORMATION (Cont.) USB Wireless Dongle RADIO FREQUENCY INTERFERENCE STATEMENT This module has been tested and found to comply with the FCC part 15 and IC RSS-210 rules. These limits are designed to provide reasonable protection against harmful interference in approved installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.