KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Note: Because CONTENTS 4 is the extract from the Operating Instructions of this model, it is subject to change without notice. You can download and refer to the original Operating Instructions on TSN Server for further information.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 1 ABOUT LEAD FREE SOLDER (PbF: Pb free) Note: In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that contains lead.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 2 FOR SERVICE TECHNICIANS ICs and LSIs are vulnerable to static electricity. When repairing, the following precautions will help prevent recurring malfunctions. 1. Cover the plastic parts boxes with aluminum foil and ground them.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 4 OPERATING INSTRUCTIONS 4.1. Battery 4.1.1. Battery Installation 1. Insert the batteries negative ( ) terminal first. 2. Close the handset cover. Note: · Use only rechargeable Ni-MH batteries P03P (HHR-4EPT).
Page 8
7 hours, the batteries must be replaced. Important: · We recommend the use of Panasonic rechargeable Ni-MH batteries P03P (HHR-4EPT). If you install non-rechargeable batteries and start charging, the batteries may leak electrolyte.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 4.2. Location of Controls 4.2.1. Base Unit 4.2.2. Handset Note: · Up to 3 menu items can be displayed at a time. To select a menu item not shown on the current page, scroll up or down by pressing the navigator key, , respectively.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 4.3. Connections 4.3.1. Base Unit When the AC adaptor is connected, a short beep will be heard. If it is not heard, check the connections. Important: · Use only the AC adaptor PQLV19CEX and telephone line cord supplied with this unit.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 4.4. Guide to Settings For your reference, a chart of all items which can be customised for the base unit and the handset is printed below. · When customising the base unit and the handset, the current item or setting is highlighted.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 4.4.3. Handset Settings Note: · Up to 3 menu items can be displayed at a time. To select a menu item not shown on the current page, scroll up or down by pressing the navigator key, , respectively.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 7.1. Check Power 7.1.1. Base Unit Is the AC Adaptor inserted into AC outlet? (Check AC Adaptor’s specification.) Cross Reference: Power Supply Circuit (P.46) 7.1.2. Handset Cross Reference: Power Supply Circuit/Reset Circuit (P.49)
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 7.9. Bell Reception 7.9.1. Base Unit 7.9.2. Handset Cross Reference: Telephone Line Interface (P.47) Check Link (P.21) HOW TO CHECK THE SPEAKER OR RECEIVER (P.43) 7.10. Check TAM Operation Cross Reference: Power Supply Circuit (P.46)
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 8 TROUBLESHOOTING BY SYMPTOM (BASE UNIT AND CHARGER UNIT) If your unit has below symptoms, follow the instructions in remedy column. Remedies depend on whether you have DECT tester (*1) or not.
Page 28
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Items Check Procedure Check or Point Replace Parts (E)* EEP-ROM Confirmation 1. EEP-ROM Confirmation (Execute the command "ChkTCD240XXrevYY"). IC3, C53, R56, R57, C57, Q6, XX: country code Q7, R64, R65, YY: revision number 2.
Page 29
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Items Check Procedure Check or Point Replace Parts (K) Frequency Offset Check Follow steps 1 to 6 of (I). IC2, IC4, R137, 7.Confirm that the frequency offset is < ± 45kHz.
Page 30
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Items Check Procedure Check or Point Replace Parts Timing Confirmation Follow steps 1 to 6 of (I). IC2, IC4, R137, 7.Confirm that the Timing accuracy is < ± 2.0ppm.
Page 31
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Items Check Procedure Check or Point Replace Parts (Q)* Audio Check 1. Link with Handset. IC4, CN1,SA1, L6, L7, D3, Q4, 2. Input -45dBm/1kHz to MIC of Handset. Q5, R23, R25, R26, R28, R63, Measure the Level at Line I/F and distortion level.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 8.2. The Setting Method of JIG (Base Unit) 8.2.1. Preparation 8.2.1.1. Equipment Required · DECT tester: Rohde & Schwarz, CMD 60 is recommended. · Frequency counter: it must be precise to be able to measure 1Hz (precision; ±4ppm).
8.3. Adjustment Standard (Base Unit) When connecting the Simulator Equipments for checking, please refer to below. LOOP AF VOLT (G) (Q) Simulator METER (I) (J) (K) (L) (M) (N) (O) (P) BELL AF VOLT DC POWER DECT Tester Simulator CMD60 METER Call - ID Simulator...
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 8.4. Check Point (Charger Unit) Items Check Procedure Check or Point Replace Parts Charging Check 1. Connect Charge Contact 12Ω/2W resistor between charge+ and charge-. D11, R11, R12 2. Measure and confirm voltage across the resistor is 2.85V ± 0.2V.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 9 TROUBLESHOOTING BY SYMPTOM (HANDSET) If your unit has below symptoms, follow the instructions in remedy column. Remedies depend on whether you have DECT tester (*1) or not. Note: (*1): A general repair is possible even if you don’t have the DECT tester because it is for confirming the levels, such as Acoustic...
Page 36
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Items Check Procedure Check or Point Replace Parts (F) Charge Control Check & 1. Apply 6V between J3(+) and J4(-) with DC power supply and set current limit to...
Page 37
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Items Check Procedure Check or Point Replace Parts (L)* Modulation Check and Follow steps 1 to 3 of (K). IC1, IC3, Adjustment 4.Confirm that the B-Field Modulation is -350 ~ -400/+320 ~ +370kHz/div using R127, C117, data type Fig 31.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Items Check Procedure Check or Point Replace Parts Power RAMP Follow steps 1 to 3 of (K). IC1, IC3, Confirmation 4.Confirm that Power RAMP is matching. R127, C117, C115, C119,...
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 9.3. The Setting Method of JIG (Handset) 9.3.1. Preparation 9.3.1.1. Equipment Required · DECT tester: Rohde & Schwarz, CMD 60 is recommended. · Frequency counter: it must be precise to be able to measure 1Hz (precision; ±4ppm).
9.4. Adjustment Standard (Handset) When connecting the Simulator Equipments for checking, please refer to below. (S) (T) Oscilloscope AF Volt Meter (K) (L) (M) (N) (O)(P)(Q)(R) Oscilloscope DECT Tester CMD60 Current Probe 8Ω 150Ω Power key BATT TP16 C125 A201 R135 (S) (T) 6.3V 47uF...
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 10 THINGS TO DO AFTER REPLACING IC Cautions: Since this page is common to each country, it may not apply to some models in your country. The contents below are the minimum adjustments required for operation.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 12 HOW TO CHECK THE SPEAKER OR RECEIVER 1. Prepare the digital voltmeter, and set the selector knob to ohm meter. 2. Put the probes at the speaker (receiver) terminals as shown below.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 15.2. Power Supply Circuit The power is supplied to the DECT BBIC, RF Module, EEPROM and Charge Contact from AC Adaptor (+6V) as shown in Fig.101. The power supply is as follows;...
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 15.3. Telephone Line Interface <Function> · Bell signal detection · Clip signal detection · ON/OFF hook circuit · Audio circuits · DTMF tone signal circuits Bell & Clip (: Calling Line Identification Presentation: Caller ID) signal detection: In the standby mode, Q4 is open to cut the DC loop current and decrease the ring load.
Page 59
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Note: *: When you enter the address, please refer to the table below. Desired Number (hex) Input Keys Desired Number (hex) Input Keys [R] + 0 [R] + 1...
Page 60
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT ex.) Items (*2) Address Default Data New Data Remarks C-ID (FSK) sensitivity 04 3D 01 (6dB up) 02 (12dB up) When hex changes from “00” to “01” or “02”, gain increases by 6dB or 12dB.
Page 62
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Note: *: When you enter the address, please refer to the table in Note: (P.59) of ENGINEERING MODE. ex.) Items (*4) Address Default Data New Data Possible Adjusted Possible Adjusted...
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 23 EEPROM LAYOUT (BASE UNIT) 23.1. Scope The purpose of this section is to describe the layout of the EEPROM (IC3) for the KX-TCD340 Base Unit. The EEPROM contains hardware, software, and user specific parameters. Some parameters are set during production of the base unit, some are set by the user configuration, and some are set during normal use of the phone.
Page 64
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Address Initial Name Description Default value Country Type Setting 0x0025 EEP_Ps0_Ipui PS ID 0x00, 0x00, 0x00, 0x00, first byte:0xA8 (Length Information) 0x00, 0x00, 0x00, 0x00, from second byte:IPUI (Normal:5byte, Max:13byte)
Page 65
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Address Initial Name Description Default value Country Type Setting 0x034F EEP_FlashTime3 Calibrated loop-break time for “100 ms” 0x0A Unit: 10 ms, defaults to 100 ms 23.3.4. Clip (Caller ID) configuration...
Page 66
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Address Initial Name Description Default Country Type value Setting 0x038D EEP_RpasMaxDuration RPAS maximum duration 0x20 Unit: 10ms, Default: 320ms 0x038E EEP_DtasDataTimeout DTAS to FSK data timeout 0x0A Unit: 100ms, Default: 1s...
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 24 EEPROM LAYOUT (HANDSET) 24.1. Scope The purpose of this section is to describe the layout of the EEPROM (IC10) for the KX-TCA132/TCA130 Handset. The EEPROM contains hardware, software, and user specific parameters. Some parameters are set during production of the handset, some are set by the user when configuring the handset, and some during normal use of the phone.
Page 69
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 24.3.2. MMI Setting Address Initial Name Description Default value Country Type Setting 0x0195 EEP_FactoryLanguage Selected Language for LCD 0x01 0x14 Setting GERAM:0 ENGLISH:1 SPANISH:2 NORWEGIAN:3 FRENCH:4 ITALIAN:5 DENISH:6 DUTCH:7 SWEDISH:8 FINNISH:9...
Page 70
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 24.3.3. MMI1 Setting Address Initial Name Description Default value Country Type Setting 0x0102 EEP_DspSdtLevel DSP Parameter SideTone2 0x00,0x0E Main:SideTone2 Main route level MictoRcv:SideTone2 MIc to Receiver level 0x0104 EEP_DspToneLevel...
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 25 HOW TO REPLACE THE FLAT PACKAGE IC Even if you do not have the special tools (for example, a spot heater) to remove the Flat IC, with some solder (large amount), a soldering iron and a cutter knife, you can easily remove the ICs that have more than 100 pins.
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 25.3. FLAT PACKAGE IC INSTALLATION PROCEDURE 1. Temporarily fix the FLAT PACKAGE IC, soldering the two marked pins. *Check the accuracy of the IC setting with the corresponding soldering foil.
27 CABINET AND ELECTRICAL PARTS (HANDSET) Note: (*1) The rechargeable Ni-MH battery P03P (HHR-4EPT) is available through sales route of Panasonic. (*2) Attach the spacer (No. 122) to the exact location described above. (*3) This cable is fixed by soldering. Refer to step...
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 30 TERMINAL GUIDE OF THE ICs, TRANSISTORS AND DIODES 30.1. Base Unit 30.2. Handset...
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 31 REPLACEMENT PARTS LIST 1. RTL (Retention Time Limited) Ref. Part No. Part Name & Description Remarks Note: PQBC10430Z1 BUTTON, PLAY ABS-HB The marking (RTL) indicates that the Retention Time is...
Page 81
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks B0JAME000095 DIODE(SI) ERJ3GEYJ104 100K PQVDS1ZB60F1 DIODE(SI) ERJ3GEYJ473 MA1Z300 DIODE(SI) ERJ3GEYJ560 MA8220 DIODE(SI) ERJ3GEYJ103...
Page 82
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R163 ERJ2GEJ273X ECUV1C224KBV 0.22 R164 ERJ2GEJ273X ECUV1C683KBV 0.068 R301 ERJ3GEYJ331 ECUV1H100DCV R302 ERJ3GEYJ222 2.2K...
KX-TCD346UAS / KX-TCD346UAT / KX-TCA132UAS / KX-TCA132UAT / KX-TCA130UAS / KX-TCA130UAT 32 FOR SCHEMATIC DIAGRAM 32.1. Base Unit (SCHEMATIC DIAGRAM (BASE UNIT_MAIN)) Notes: 1. DC voltage measurements are taken with voltmeter from the negative voltage line. 2. This schematic diagram may be modified at any time with the development of new technology.