Table of Contents
Advertisement
Electrical connection
-
Before plugging the appliance into the mains socket,
check that the mains power supply corresponds to the
value indicated on the rating plate and that the mains
power supply is adequate for the load.
-
THIS APPLIANCE COMPLIES WITH DIRECTIVE 2004/108/
EEC ON RADIO INTERFERENCE SUPPRESSION.
Mounting the base
-
Fit the two parts of the base together, matching the
guide pins on the front with the recesses on the back
and snapping the two clips into place (fig. A and fig. B).
-
Turn the appliance upside down and position the
assembled base on the appliance in order to couple
the two openings with the two tabs on the appliance,
tilting it as shown in figure C, consequently turn the
base down till the two frontal teeth snaps into position
(figure D).
-
Assembly time: approx. 5 minutes.
-
Optional
- Fasten the tower to the base using the screw
provided to achieve extra stability.
- Tools needed and estimated time:
1 Phillips head screwdriver type PH 2 x 100
1 screws (included)
Assembly time: approx. 2 minutes.
Operation and use
1. Plug into the mains socket.
2. The appliance emits a beep. The indicator light (H)
comes on and remains lit while the appliance is
powered.
3. The appliance switches to stand-by. A dot flashing
on the display means the tip over device has been
activated. See paragraph: "Safety functions".
4. Press ON/STAND-BY (A) to turn the appliance on. It
begins heating the room according to the current
settings.
5. Press the MODE button (C) to select one of the following
operating modes:
Fan
Freeze prevention
Heating 1
Heating 2
Heating 3
5.1 Fan
In this mode, only the fan operates and the appliance does
not heat the room.
5.2 Freeze prevention
In this mode, the appliance keeps the room at a temperature
of 7°C to avoid freezing.
5.3 Heating 1, 2 and Heating 3
In this mode, the desired temperature can be selected by
pressing the adjustment buttons + and – ( B ):
-
Heating 1
The appliance operates at low power, reducing noise
levels and energy consumption to a minimum.
Heating 2
-
The appliance operates at medium power.
-
Heating 3
The appliance operates at high power to heat the room
rapidly.
6. "ECO plus" function
The "ECO plus" function is available in Heating 1, 2 and 3
modes only. To activate the function, press the "ECO plus"
button (D). When this function is active the appliance
automatically sets the most appropriate power level
to guarantee optimum comfort while reducing energy
consumption. While the "ECO plus" function is active, the
appliance may switch automatically to a lower heating power
than the one displayed. This may happen a number of times
during use.
7. To distribute the air flow over a wider surface, press the
swing button (F)
to the right and left. To stop the appliance in the desired
position, simply press the swing button (F) again.
8. To turn the appliance off, press the ON/STAND-BY
button (A). The display may visualize a countdown for
about 6 seconds.
Please note: Room temperature can be displayed in
either °C or °F. To change the unit of measurement for the
temperature, press and hold the + button for a few seconds,
then release.
Digital 24 h timer
This function can be activated from any operating mode.
Auto-start: with the appliance in STAND-BY, press the
timer button
(E) . The
with the time remaining before the appliance comes on. To
adjust the timer, use the adjustment buttons + and - (B),
then wait a few seconds for the setting to be memorised.
The stand-by light (H) is displayed together with the
symbol, indicating that the timer has been set. When the
programmed time is reached, the appliance comes on with
the settings used during the previous period of operation.
Auto-off: with the appliance on, press the timer button
(E). The
symbol is displayed together with the time
remaining before the appliance goes off.
6
. The appliance starts oscillating
symbol is displayed together
Advertisement
Table of Contents
