Appendix; Appendix A. Instructions Converted By Change Model On Cx-Programmer - Omron C200HS Series Replacement Manual

7.

Appendix

Appendix A. Instructions converted by Change Model on CX-Programmer.

(1) The data type of operand is changed from BCD to binary for some instructions.
(2) The number of operands is changed for some instructions.
(3) Interrupt control instructions must be changed. (Use MSKS, MSKR, CLI, DI, and EI).
Refer to the list below for details. The table lists the instructions which differ between before and after conversion. The other
instructions remain unchanged after conversion.
Instruction for C200HS
JMP(04) JMP(004) or
JMP0(515)
JME(05) JME(005) or
JME0(516)
WSFT(16) Same as C200HS
FUN17 ASFT(017)
XFER(70) XFERC(565)
MOVB(82) MOVBC(568)
DIST(80) DISTC(566)
COLL(81) COLLC(567)
FUN60 CMPL(060)
FUN19 MCMP(019)
FUN63 LINE(063)
FUN64 COLM(064)
FUN65 SEC(065)
FUN66 HMS(066)
INC(38) ++B(594)
DEC(39) --B(596)
ADD(30) +B(404)
ADDL(54) +BL(405)
SUB(31) -B(414)
SUBL(55) -BL(415)
MUL(32) *B(424)
MULL(56) *BL(425)
DIV(33) /B(434)
DIVL(57) /BL(435)
ADB(50) +(400)
SBB(51) -(410)
MLB(52) *(420)
DVB(53) /(430)
FUN69 APR(069)
FUN89 Not supported
STEP(08) Same as C200HS
SNXT(09) Same as C200HS
Use a differentiated
execution condition
for the SNXT
instruction.
FAL(06) Same as C200HS
FALS(07) Same as C200HS
MSG(46) MSG(046)
FUN47 Not supported
FUN67 BCNTC(621)
WDT(94) WDT(094)
FUN61 Not supported
FUN18 Enter the settings in the PLC Setup.
FUN48 Not supported
FUN49 Enter the settings in the PLC Setup.
FUN90 SEND(090)
FUN98 RECV(098)
16
Instruction for CJ2
When #0 is set to the operand, JMP is converted to
JMP0 and the operand is deleted.
If a value other than #0 is set, the operand is the same.
When #0 is set to the operand, JME is converted to
JME0 and the operand is deleted.
If a value other than #0 is set, the operand is the same.
#0 is added to the first operand.
WSFT St E → WSFT #0 St E
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Changed from BCD data to binary data.
Changed from BCD data to binary data.
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Same as C200HS
Combine and use the following instructions: MSKS(690), CLI(691), MSKR(692),
DI(693), EI(694)
The CIO, Holding, Work, Auxiliary, Link Areas are all
converted into the Work Area.
Same as C200H
#0 is added to the second operand.
FAL N
#0 is added to the second operand.
FALS N
#0 is added to the first operand.
MSG FM
The number of characters (words) to be registered
from the first message word is changed from 16
characters (8 words) to 32 characters (16 words).
Use MSG(046) instead.
Same as C200HS
Control data configuration is changed.
Use IORF (097) instead.
―
Control data configuration is changed.
Control data configuration is changed.
Operand
FAL N #0
FALS N #0
MSG #0 M
Number of operands
#0: Changed from 1 to 0
<> #0: Same
#0: Changed from 1 to 0
<> #0: Same
Changed from 2 to 3
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Same
Changed from 1 to 2.
Changed from 1 to 2.
Changed from 1 to 2.
―
Same
Same
―
Same
Same