Milwaukee M18 BPFPCCS Operator's Manual page 5

Ensure battery door is closed
WARNING
and
chemicals are present.
Filling the Tank
WARNING Before filling the tank, remove
the tank from the base.
Ensure battery door is closed and latched
whenever chemicals are present.
Mix chemicals per manufacturer's instructions.
Failure to follow instructions may cause harsh
chemicals to injure user or damage tool.
A removable strainer prevents debris that can clog
or damage the pump from entering the tank. Label
tank contents accordingly during each use. Only
put recommended liquids in tank. Only use water in
water supply tank.
1. Ensure the battery door is
closed securely.
2. Remove the tank from the base
and set on a level surface away
from the base to prevent exposing
the base to harsh chemicals.
3. Unscrew and remove the tank
cap; ensure strainer is in place.
4. Fill the tank (up to 15 litres; do
not overfill). Use the litre markings
on the side of the tank as a guide.
5. Reinstall the tank cap.
6. Reinstall the tank.
Installing the Tank
1. Ensure the battery door is closed securely.
2. Slide tank hooks into base and seat tank into
tank reservoir in the base.
3. Secure tank to base with front and rear tank
latches; ensuring the tank is level, firmly seated,
and all seals are aligned.
WARNING When filled, the sprayer will be
heavy, take care when putting
on the backpack to avoid strain.
Putting on the Backpack
1. Ensure tank is securely attached to base with
front and rear tank latches, tank cap is installed,
and battery door is latched.
2. Pick up the backpack by one of the shoulder
straps, slide your arms through each shoulder
strap.
3. With the sprayer on your back, tighten the
shoulder and waist straps until they fit snugly and
securely, high on your back. Connect chest strap.
4. Be sure the shoulder, chest, and waist straps are
tight but comfortable; if they are too loose, the
sprayer may slide around on your back, making it
uncomfortable to wear.
5. Be aware tank contents may shift during use and
movement, such as twisting or bending over.
OPERATION
Adjusting the Flow Rate
Select the desired flow rate from Low (1) to High
(5), depending on the job and the chemical
manufacturer's instructions.
Flow M18 BPFPCS-0
Rate (Stream Nozzle)
1 0.37 L/min
2 0.52 L/min
3 0.90 L/min
4 1.32 L/min
5 1.93 L/min
latched whenever
M18 BPFPCCS-0 M18 BPFPWS-0
(Stream Nozzle) (Open Flow)
0.53 L/min 0.5 L/min
0.79 L/min 0.83 L/min
1.24 L/min 1.32 L/min
1.66 L/min 2.00 L/min
3.1 L/min 4.2 L/min
WARNING T o reduce the risk of injury ,
always
protective equipment (PPE) according to the
chemical manufacturer's instructions. Always
wear eye protection. Always ensure battery
compartment latch is securely closed before
use.
Ensure trigger handle lock-on is not engaged
before turning ON tool.
Turning the Sprayer ON/OFF
1. Install the battery pack. Close and latch the
battery compartment.
2. To turn the sprayer ON, press the ON/OFF
switch to "I". The Power LED will light green.
3. To start the flow of liquid at the spray wand, pull
the trigger.
4. To stop the flow of liquid at the spray wand,
release the trigger.
5. To turn the sprayer OFF, press the ON/OFF
switch to "0".
NOTE: Be aware some spray material may remain
inside the spray wand and drip out. To drain, turn
off the tool, then pull the trigger and point the tool
down until dripping stops.
Trigger Lock-On
(Cat. No. 491628PS, 491628CS)
Use trigger lock-on when spraying for an extended
period of time or when covering a large area.
1. To lock-on, pull the trigger and push in the
lock-on button.
2. To release the lock-on, pull and release the
trigger.
NOTE: Ensure the trigger is not locked on before
turning the sprayer off to avoid accidental spraying
when the sprayer is restarted.
Trigger Lock-On
Trigger Lock-Off
(Cat. no. 491628PS, 491628CS)
To avoid accidental spraying, lock-off the trigger.
1. Press the lock-off toggle at the end of the trigger
(1).
2. Hook the lock-off tab onto the hook under the
trigger (2).
3. To release, push the tab back into the trigger.
5
wear personal
2
1