Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Synology DiskStation DS2419+
Summary of Contents for Synology DiskStation DS2419+
- Page 1 Synology DiskStation DS2419+ Hardware Installation Guide...
-
Page 2: Table Of Contents
Table of Contents Chapter 1: Before You Start Package Contents Synology DiskStation at a Glance Safety Instructions Chapter 2: Hardware Setup Tools and Parts for Drive Installation Install Drives Start Up Your DiskStation Add a RAM Module on DiskStation Add a Network Interface Card... -
Page 3: Package Contents
Chapter Before You Start Thank you for purchasing this Synology product! Before setting up your new DiskStation, please check the package contents to verify that you have received the items below. Also, make sure to read the safety instructions carefully to avoid harming yourself or damaging your DiskStation. -
Page 4: Synology Diskstation At A Glance
This port is used for manufacturing use only. Expansion Port Connect Synology Expansion Unit to the DiskStation here. LAN Port Connect network cables here. For more information about Synology Expansion Unit supported by your DiskStation, please visit www.synology.com. 4 Chapter 1: Before You Start... -
Page 5: Safety Instructions
Safety Instructions Keep away from direct sunlight and away from chemicals. Make sure the environment does not experience abrupt changes in temperature or humidity. Place the product right side up at all times. Do not place near any liquids. Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or aerosol cleaners. -
Page 6: Chapter 2: Hardware Setup
• A screwdriver (only for 2.5” drives) • At least one 3.5” or 2.5” SATA drive (please visit www.synology.com for compatible drive models.) If you install a drive that contains data, the system will format the drive and erase all existing data. Please Warning: back up any important data before installation. - Page 7 3 Load drives in the drive trays. • For 3.5” drives: Remove the fastening panels from the sides of the drive tray. Place the drive in the drive tray. Then insert the fastening panels to secure the drive in place. •...
- Page 8 6 Insert the drive tray key into the drive tray lock, turn the key clockwise (to the “-” position) to lock the handle of the drive tray, and then remove the key. 7 Repeat the steps above to assemble the other drives you have prepared. 8 Drives are numbered as shown below.
-
Page 9: Start Up Your Diskstation
Start Up Your DiskStation 1 Use the LAN cable to connect the DiskStation to your switch, router or hub. 2 Connect one end of the AC power cord to the power port of the DiskStation, and the other to the power outlet. 3 Press the power button. -
Page 10: Add A Ram Module On Diskstation
Add a RAM Module on DiskStation The optional Synology DDR4 RAM module is designed for DiskStation memory expansion. Follow the steps below to install, check, or remove a RAM module on your DiskStation. To install the RAM module: 1 Press and hold the power button until you hear a beep sound to shut down your DiskStation. Disconnect all cables from your DiskStation to prevent any possible damage. - Page 11 3 Insert the new RAM module in the slot: a Align the notch on the gold edge of the module with the notch in the memory slot. Then tilt the card and insert the module into the slot. Make sure the module is properly inserted. b Push the RAM module with moderate pressure into the memory slot until you hear a click.
- Page 12 To make sure DiskStation recognizes the new memory capacity: 1 Install DiskStation Manager (DSM). (See the next chapter for more information.) 2 Log in to DSM as admin or a user belonging to the administrators group. 3 Check Total Physical Memory Control Panel >...
-
Page 13: Add A Network Interface Card
2 Remove the 2 screws on the top of the back panel, and then pull the top cover in the direction as illustrated below. For more information about supported 10GbE or Gigabit network interface cards, please visit www.synology.com. 13 Chapter 2: Hardware Setup... - Page 14 3 Remove the PCIe expansion slot shield: a Reposition your DiskStation so that the top will be facing your body, with drive trays on the right side. b Pull the clip above the PCIe expansion slot shield in the direction as illustrated below. c Remove the shield.
- Page 15 b Use two fingers with firm, even pressure to push down on the card and the bracket. c Push back the clip to secure the newly inserted card. Note: Make sure the connectors are fully inserted. Otherwise, the network interface card might not be able to function properly.
-
Page 16: Replace System Fan
Replace System Fan Your DiskStation will play beep sounds if either of the system fans is not working. Follow the steps below to replace the malfunctioning fan module with a good one. To replace the system fan module: 1 Shut down your DiskStation. Disconnect all cables connected to your DiskStation to prevent any possible damages. -
Page 17: Chapter 3: Install Dsm On Diskstation
Chapter Install DSM on DiskStation After hardware setup is finished, please install DiskStation Manager (DSM) – Synology’s browser-based operating system – on your DiskStation. Install DSM with Web Assistant Your DiskStation comes with a built-in tool called Web Assistant that helps you download the latest version of DSM from the Internet and install it on your DiskStation. - Page 18 Supported RAID Types • RAID 5 • RAID 6 • RAID 10 • Synology Hybrid RAID (Up to 2-Disk Fault Tolerance) Agency Certifications • FCC Class B • CE Class B • BSMI Class B • EAC • VCCI Class B • RCM •CCC...
-
Page 19: Appendix B: Led Indicator Table
No network Static Drive ready and idle Green Blinking Accessing drive Drive Status Indicator (on tray) Orange Static Drive error No internal drive Note: Model specifications are subject to change without notice. Please refer to www.synology.com for the latest information.