Specifications - Panasonic SC-PMX90 Owner's Manual

"DEVICE NO RESPONSE"
"HUB NOT SUPPORTED"
"NOT SUPPORTED"
• You have connected an unsupported USB device.
"OPT UNLOCKED"
• "OPT" is selected, but no device is connected.
• The sampling frequency components, etc. of the audio
signals are not input correctly.
– For supported formats, refer to "Connecting to OPT IN
(Optical Audio In) terminal" (
"PC UNLOCKED"
• "PC" is selected, but a PC is not connected.
"PGM FULL"
• The number of programed tracks is more than 24.
"PLAYERROR"
• You played an unsupported file. The system will skip
that track and play the next one.
"READING"
• The unit is checking the CD information. After this
display has disappeared, start operating.
• When starting playback of DSD files, it may take time
to read the file. Wait until reading completes.
"REMOTE " (" " stands for a number.)
• The remote control and this unit are using different
codes. Change the code on the remote control.
– When "REMOTE 1" is displayed, press and hold [OK]
and [1] for at least 4 seconds.
– When "REMOTE 2" is displayed, press and hold [OK]
and [2] for at least 4 seconds.
"USB OVER CURRENT ERROR"
• The USB device is drawing too much power. Remove
the USB device. Switch the system off and on again.
"VBR"
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
"WAIT"
• This is displayed, for example, when this unit is turning
off.
16
Memory reset (initialization)
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC power supply cord.
Wait 30 seconds before you continue with step 2.
2
While you press and hold [Í/I] on the main unit,
5).
connect the AC power supply cord again.
Keep holding down [Í/I] until "---------" appears on
the display.
3
Release [Í/I].
All the settings are set back to the factory default.
It is necessary to set the memory items again.
Remote control code
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
To set the code to "REMOTE 2"
1
Press [SELECTOR] on the main unit to select
"CD".
2
Press and hold [∫] on the main unit and [2] on
the remote control until "REMOTE 2" is shown.
3
Press and hold [OK] and [2] for a minimum of
4 seconds.
• The factory default is "REMOTE 1".
• To change the mode back to "REMOTE 1", repeat the
steps above but replace the button pressed on the
remote control from [2] to [1].

Specifications

General
Power supply
Power consumption
Dimensions (main unit)
(W k H k D) 211 mm k 114 mm k 267 mm
(8
Mass (main unit) Approx. 2.8 kg (6.2 lbs
Operating temperature range
0 °C to +40 °C (r32
Operating humidity range
35 % to 80 % RH (no condensation)
Power consumption in standby mode*
(When "BLUETOOTH STANDBY" is "ON")*
*1: "BLUETOOTH STANDBY" is "OFF".
*2: No device is connected to the USB port before turning to
standby mode.
Amplifier section
RMS output power
Front Ch (both ch driven)
60 W per channel (3 ™), 1 kHz, 10% THD
Total RMS power
FM section
Preset memory
Frequency range
87.9 MHz to 107.9 MHz (200 kHz step)
87.5 MHz to 108.0 MHz (100 kHz step)
Antenna terminals
Disc section
Disc played (8 cm (3q) or 12 cm (5q))
CD, CD-R/RW (CD-DA, MP3*
Pick up
Wavelength
*3: MPEG-1 Layer 3, MPEG-2 Layer 3
AC 120 V, 60 Hz
40 W
/ / /
5 qk4 1 qk10 1 q)
16 2 2
)
o F to r104 o F)
1, 2
0.25 W (approx.)
2
0.35 W (approx.)
120 W
30 stations
75 ™ (unbalanced)
3 )
790 nm (CD)