Sony HT-DDW670 Operating Instructions (HT-DDW670) Operating Instructions Manual page 41

Models of area code AU
(6 ohms 120 Hz – 20 kHz, THD 0.09%)
2)
FRONT :
2)
CENTER :
2)
SURR :
(6 ohms 100 Hz, THD 0.09%)
2)
SUB WOOFER :
(6 ohms 1 kHz, THD 0.7%)
2)
FRONT :
2)
CENTER :
2)
SURR :
(6 ohms 100 Hz, THD 0.7%)
2)
SUB WOOFER :
(6 ohms 1 kHz, THD 10%)
2)
FRONT :
2)
CENTER :
2)
SURR :
(6 ohms 100 Hz, THD 10%)
2)
SUB WOOFER :
1) Measured under the following conditions:
Area code
U, CA
CEL, CEK, SP
AU, E51
MX
2) Depending on the sound field settings and the
source, there may be no sound output.
Inputs (Analog)
SA-CD/CD, DVD,
VIDEO 1, 2
Inputs (Digital)
DVD (Coaxial)
SA-CD/CD (Optical)
Output (Analog)
SUB WOOFER
Reproduction frequency range:
Tone
Gain levels
40 W/ch
40 W
40 W/ch
40 W
50 W/ch
50 W
50 W/ch
50 W
85 W/ch
85 W
85 W/ch
85 W
Power requirements
120 V AC, 60 Hz
230 V AC, 50 Hz
240 V AC, 50 Hz
127 V AC, 60 Hz
Sensitivity: 800 mV
Impedance: 50 k ohms
Sensitivity: –
Impedance: 75 ohms
Sensitivity: –
Impedance: –
Voltage: 2 V
Impedance: 1 k ohm
28 – 20,000 Hz
±6 dB, 1 dB step
FM tuner section
Tuning range
Antenna
Antenna terminals
Intermediate frequency
AM tuner section
Tuning range
Models of area code U, CA
With 10-kHz tuning scale: 530 – 1,710 kHz
With 9-kHz tuning scale: 531 – 1,710 kHz
Models of area code CEL, CEK, AU, SP
With 9-kHz tuning scale: 531 – 1,602 kHz
Model of area code E51
With 10-kHz tuning scale: 530 – 1,610 kHz
With 9-kHz tuning scale: 531 – 1,602 kHz
Models of area code MX
With 10-kHz tuning scale: 530 – 1,610 kHz
Antenna
Intermediate frequency
3) You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off the
receiver. While holding down PRESET TUNING +
or TUNING +, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the procedure.
General
Power requirements
Area code
U, CA
CEL, CEK
AU
E51
SP
MX
Power consumption
Area code
U, SP, E51, AU, CEL,
CEK, MX
CA
87.5 - 108.0 MHz
FM wire antenna
75 ohms, unbalanced
10.7 MHz
3)
3)
3)
3)
Loop antenna
450 kHz
Power requirements
120 V AC, 60 Hz
230 V AC, 50/60 Hz
240 V AC, 50 Hz
120/220/240 V AC,
50/60 Hz
220-230 V AC, 50/60 Hz
127 V AC, 60 Hz
Power consumption
160 W
220 VA
continued
GB
41