Sony HT-DDW670 Operating Instructions (HT-DDW670) Operating Instructions Manual

Home theater system
Hide thumbs Also See for HT-DDW670 Operating Instructions (HT-DDW670):
Table of Contents

Advertisement

2-342-216-13(1)
Home Theatre
System

Operating Instructions

Owner's Record
The model and serial numbers are located on the rear of the unit. Record the serial
number in the space provided below. Refer to them whenever you call upon your
Sony dealer regarding this product.
Model No.
Serial No.
HT-DDW670
©2005 Sony Corporation

Advertisement

Table of Contents
loading

Summary of Contents for Sony HT-DDW670 Operating Instructions (HT-DDW670)

  • Page 1: Operating Instructions

    Owner’s Record The model and serial numbers are located on the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. Serial No.
  • Page 2 BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. For customers in the United States, Canada and Australia ® is a U.S. registered NERGY mark. As an E NERGY Sony Corporation has determined that this product meets the E guidelines for energy efficiency. ® partner, ® NERGY...
  • Page 3: About This Manual

    About This Manual • The instructions in this manual are for model HT-DDW670. Check your receiver’s model number by looking at the lower right corner of the front panel. • The instructions in this manual describe the controls on the receiver. You can also use the controls on the supplied remote if they have the same or similar names as those on the receiver.
  • Page 4: Table Of Contents

    Table of Contents Getting Started 1: Check how to hookup your components ... 5 1a: Connecting components with digital audio output jacks ... 7 1b: Connecting components with only analog audio jacks ... 9 2: Connecting the antennas ... 10 3: Connecting speakers ...
  • Page 5: 1: Check How To Hookup Your Components

    Getting Started 1: Check how to hookup your components Steps 1a through 1b beginning on page 7 describe how to hook up your components to this receiver. Before you begin, refer to “Connectable components” below for the pages which describe how to connect each component.
  • Page 6: Required Cords

    Required cords The hookup diagrams on the subsequent pages assume the use of the following optional connection cords (A to C) (not supplied unless indicated). A Audio cord White (L) Red (R) B Optical digital cord Notes • Turn off the power to all components before making any connections. •...
  • Page 7: 1A: Connecting Components With Digital Audio Output Jacks

    1a: Connecting components with digital audio output jacks Hooking up a DVD player For details on the required cords (A OUTPUT DIGITAL COAXIAL DIGITAL OPTICAL SA-CD/ DVD IN COAXIAL C), see page 6. – DVD player OUTPUT AUDIO ANTENNA AUDIO AUDIO IN AUDIO IN AUDIO IN...
  • Page 8 Hooking up a Super Audio CD/CD player For details on the required cords (A OPTICAL SA-CD/ DVD IN COAXIAL DIGITAL OPTICAL All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz and 96 kHz sampling frequencies. Note The sound is not output when you play a Super Audio CD on the Super Audio CD player connected to the SA-CD/CD OPTICAL IN jack on this receiver.
  • Page 9: 1B: Connecting Components With Only Analog Audio Jacks

    1b: Connecting components with only analog audio jacks For details on the required cords (A DVD player OUTPUT AUDIO DIGITAL OPTICAL SA-CD/ DVD IN COAXIAL Super Audio CD/CD C), see page 6. – Satellite Tuner or VCR OUTPUT AUDIO ANTENNA AUDIO AUDIO IN AUDIO IN...
  • Page 10: 2: Connecting The Antennas

    2: Connecting the antennas Connect the supplied AM loop antenna and FM wire antenna. DIGITAL OPTICAL SA-CD/ DVD IN COAXIAL The shape of the connector varies depending on the area code. Notes • To prevent noise pickup, keep the AM loop antenna away from the receiver and other components. •...
  • Page 11: 3: Connecting Speakers

    3: Connecting speakers Connect your speakers to the receiver. This receiver allows you to use a 5.1 channel speaker system. To fully enjoy theater-like multi channel surround sound requires five speakers (two front speakers, a center speaker, and two surround speakers) and a sub woofer (5.1 channel). Example of 5.1 channel speaker system configuration Center speaker Front speaker (Left)
  • Page 12 Required cords A Speaker cords (supplied) (–) Center speaker AUDIO WOOFER Sub woofer * If you have an additional active subwoofer, connect it to SUB WOOFER AUDIO OUT jack. B Monaural audio cord (not supplied) Black Front speaker Front speaker (Right) WOOFER SURROUND...
  • Page 13: Installing The Speakers On The Wall

    • Contact a screw shop or installer regarding the wall material or screws to be used. • Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or improper screw installation, natural...
  • Page 14: 4: Connecting The Ac Power Cord

    4: Connecting the AC power cord Setting the voltage selector If your receiver has a voltage selector on the rear panel, check that the voltage selector is set to the local power supply voltage. If not, use a screwdriver to set the selector to the correct position before connecting the AC power cord to a wall outlet.
  • Page 15: 5: Setting Up The Speakers

    5: Setting up the speakers You can use the SET UP menu to set the distance and location of the speakers connected to this receiver. Press ?/1 to turn on the receiver. Press MAIN MENU repeatedly to select “ SET UP ”. Press repeatedly to select the parameter you want to adjust.
  • Page 16 The receiver lets you to input the speaker position in terms of distance. However, it is not possible to set the center speaker further than the front speakers. Also, the center speaker cannot be set more than 1.5 meters (5 feet) closer than the front speakers. Likewise, the surround speakers cannot be set further away from the listening position than the front speakers.
  • Page 17: 6: Adjusting The Speaker Levels And Balance

    6: Adjusting the speaker levels and balance — TEST TONE Adjust the speaker levels and balance while listening to the test tone from your listening position. Use the remote for the operation. The receiver employs a test tone with a frequency centered at 800 Hz.
  • Page 18: Amplifier Operation

    Amplifier Operation Selecting the component Press input buttons to select the input. To select the Satellite tuner DVD player Super Audio CD or CD player Built-in tuner (FM/AM) The selected input appears in the display. Turn on the component and start playback.
  • Page 19: Listening To Fm/Am Radio

    Listening to FM/AM radio You can listen to FM and AM broadcasts through the built-in tuner. Before operation, make sure you have connected the FM and AM antennas to the receiver (see page 10). The tuning scale differs depending on the area code as shown in the following table.
  • Page 20: Storing Fm Stations Automatically

    Storing FM stations automatically — AUTOBETICAL (Models of area code CEL, CEK only) This function lets you store up to 30 FM and FM RDS stations in alphabetical order without redundancy. Additionally, it only stores the stations with the clearest signals. If you want to store FM or AM stations one by one, see “Presetting radio stations”...
  • Page 21: Using The Radio Data System (Rds)

    Tuning to preset stations Press FM or AM to select the FM or AM band. The last received station is tuned in. Press PRESET TUNING + or PRESET TUNING – repeatedly to select the preset station you want. Each time you press the button, you can select the preset station as follows: tA1yA2y...yA0yB1yB2y...yB0T tC0y...yC2yC1T...
  • Page 22 Notes • If there is an emergency announcement by government authorities, “ALARM” flashes in the display. • When the message consists of 9 characters or more, the message scrolls across the display. • If a station does not provide a particular RDS service, “NO XXXX”...
  • Page 23: Changing The Display

    Changing the display Changing the information in the display You can check the sound field etc. by changing the information in the display. Press DISPLAY repeatedly. Each time you press DISPLAY, the display will change cyclically as follows. t Selected input t Index name of the input Sound field currently applied When the tuner is selected...
  • Page 24: About The Indications In The Display

    About the indications in the display SLEEP OPT COAX SL S SR A SW: Lights up when audio signal is output from the SUB WOOFER jack. B LFE: Lights up when the disc being played back contains the LFE (Low Frequency Effect) channel and the LFE channel signal is actually being reproduced.
  • Page 25: Enjoying Surround Sound

    Enjoying Surround Sound Using only the front speakers and sub woofer — 2CH STEREO In this mode, the receiver outputs the sound from the front left/right speakers and sub woofer. When multi channel surround formats are input, the signals are downmixed to 2 channel with bass frequencies being output from the sub woofer.
  • Page 26: Selecting A Sound Field

    Sound fields with marks use DCS technology. DCS is the concept name of the surround technology for home theater developed by Sony. DCS uses the DSP (Digital Signal Processor) technology to reproduce the sound characteristics of an actual cinema cutting studio in Hollywood.
  • Page 27: Selecting A Sound Field For Music

    C.ST.EX C (CINEMA STUDIO EX C) Reproduces the sound characteristics of the Sony Pictures Entertainment scoring stage. This mode is ideal for watching musicals or films where orchestra music is featured in the soundtrack. About CINEMA STUDIO EX modes CINEMA STUDIO EX modes are suitable for watching motion picture DVDs (etc.), with...
  • Page 28: Advanced Adjustments And Settings

    Advanced Adjustments and Settings Switching the audio input mode for digital components — INPUT MODE You can switch the audio input mode for components which have digital audio input jacks. Press input buttons to select the input. Press INPUT MODE repeatedly to select the audio input mode.
  • Page 29: Resetting Sound Fields To The Initial Settings

    x CTR XXX dB (Center speaker level) x SUR.L. XXX dB (Surround speaker (left) level) x SUR.R. XXX dB (Surround speaker (right) level) x S.W. XXX dB (Sub woofer level) Initial setting: 0 dB You can adjust from –10 dB to +10 dB in 1 dB steps. COMP.
  • Page 30: Adjusting The Tone

    Adjusting the tone You can adjust the tonal quality (bass, treble level) of the front speakers using the TONE menu. Start playing a source encoded with multi channel surround effects (DVD, etc.). Press MAIN MENU repeatedly to select “ TONE ”. Press repeatedly to select the parameter you want to adjust.
  • Page 31 x DEC. XXXX (Digital audio input decoding priority) Lets you specify the input mode for the digital signal input to the DIGITAL IN jacks. • AUTO Automatically switches the input mode between DTS, Dolby Digital, or PCM. • PCM PCM signals are given priority (to prevent the interruption when playback starts).
  • Page 32: Other Operations

    Other Operations Naming preset stations and inputs You can enter a name of up to 8 characters for preset stations and inputs selected with input buttons, and display it in the receiver’s display. To index a preset station Press FM or AM to select the FM or AM band, then tune in the preset station you want to create an index name for (page 21).
  • Page 33: Operations Using The Remote Rm-Aau002

    Operations Using the Remote RM-AAU002 You can use the remote RM-AAU002 to operate the components in your system. Before you use your remote Inserting batteries into the remote Insert R6 (size-AA) batteries with the + and – properly oriented in the battery compartment. When using the remote, point it at the remote sensor on the receiver.
  • Page 34 The tables below show the settings of each button. Remote Operations Button A.F.D. ef Receiver ANGLE DVD player ANT 0 VCR/ Satellite tuner AUDIO DVD player/ Satellite tuner VCR/ MENU qd DVD player/ Satellite tuner AV ?/1 VCR/ CD player/ DVD player/ Satellite tuner/ MD deck...
  • Page 35 SUBTITLE DVD player Changes the subtitles. SYSTEM Receiver/ Turns off the receiver STANDBY TV/VCR/ and other Sony audio/ (Press AV CD player/ video components. ?/1 1 and DVD player/ ?/1 2 at Satellite tuner/ the same MD deck...
  • Page 36: Changing The Factory Setting Of An Input Button

    DSS (Digital Satellite Receiver) DCS (Digital CS Tuner) BSD (Digital BS Tuner) *Sony VCRs are operated with a VTR 2 or 3 setting. These correspond to 8 mm and VHS respectively. Now you can use the DVD button to control the CD player.
  • Page 37: Additional Information

    Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. If you have any question or problem concerning your receiver, please consult your nearest Sony dealer.
  • Page 38: Troubleshooting

    Troubleshooting If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help you remedy the problem. There is no sound or only a very low-level sound no matter which component is selected. • Check that the speakers and components are connected securely and correctly.
  • Page 39: Remote Control

    PROTECT Irregular current is output from the speakers. The receiver will automatically turn off after a few seconds. Check the speaker connection and turn on the power again. If this problem persists, consult your nearest Sony dealer. on the continued...
  • Page 40: Specifications

    If the problem persist Consult your nearest Sony dealer. Reference sections for clearing the receiver’s memory To clear All memorized settings...
  • Page 41 Models of area code AU (6 ohms 120 Hz – 20 kHz, THD 0.09%) FRONT 40 W/ch CENTER 40 W SURR 40 W/ch (6 ohms 100 Hz, THD 0.09%) SUB WOOFER 40 W (6 ohms 1 kHz, THD 0.7%) FRONT 50 W/ch CENTER 50 W...
  • Page 42 Power consumption (during standby mode) 0.2 W Dimensions (w/h/d) (Approx.) 430 × 145 × 301.5 mm (17 × 5 6/8 × 11 7/8 inches) including projecting parts and controls Mass (Approx.) 6.5 kg (14 lb 6 oz) Speaker section Models of area code CEL, CEK Front speakers (SS-MSP67LE/ SS-MSP67RE) Center speaker (SS-CNP87)
  • Page 43: List Of Button Locations And Reference Pages

    List of button locations and reference pages How to use this page Use this page to find the location of buttons that are mentioned in the text. Main unit ALPHABETICAL ORDER A - H A.F.D. 9 (25, 26, 27) AM qh (18, 19, 32, 41) DIMMER 3 (23) DISPLAY 2 (21, 23, 39) Display 5 (21, 23)
  • Page 44: Index

    Installing the speakers 13 Labeling. See Naming LEVEL menu 28 Naming 32 Preset stations how to 20 how to tune 21 RDS 21 Sony Corporation Printed in Malaysia Selecting component 18 – sound field 26 SET UP menu 15 Sleep Timer 32...

Table of Contents