Field Settings; Procedure - Daikin EKHBHE008BA3V3 Operation Manual

NOTE When booster heater and domestic hot water
schedule timers are used, make sure they are
enabled during
heating/cooling is disabled.
Example pattern:
0 0 0 0 : : : : 0 0 0 0 0 0 0 0 1 1 1 1 : : : : 0 0 0 0 0 0 0 0
Space
heating/cooling
Domestic water
heating
Booster heating
In case the disinfection function is required, the
schedule timer for domestic water heating and
booster heating must be used. If the domestic
water heating and booster heater are not stopped,
than this disinfection can not start.
Disinfection example pattern (refer to paragraph
"[2] Disinfection
manual).
Mon
Pattern 1
Pattern 2 —
Pattern 1
0 0 0 0 : : : : 0 0 0 0 0 0 0 0 1 1 1 1 : : : : 0 0 0 0 0 0 0 0
Space
heating/cooling
Domestic water
heating
Booster heating
Pattern 2
0 0 0 0 : : : : 0 0 0 0 0 0 0 0 1 1 1 1 : : : : 0 0 0 0 0 0 0 0
Space
heating/cooling
Domestic water
heating
Booster heating
Disinfection
function
Operation manual
13
the period that
2 2 2 2 : : : : 0 0 0 0 0 0 0 0 3 3 3 3 : : : : 0 0 0 0 0 0 0 0 4 4 4 4 : : : : 0 0 0 0 0 0 0 0 5 5 5 5 : : : : 0 0 0 0 0 0 0 0 6 6 6 6 : : : : 0 0 0 0 0 0 0 0
function" in the operation
Tue Wed Thu Fri Sat
—
— — — —
2 2 2 2 : : : : 0 0 0 0 0 0 0 0 3 3 3 3 : : : : 0 0 0 0 0 0 0 0 4 4 4 4 : : : : 0 0 0 0 0 0 0 0 5 5 5 5 : : : : 0 0 0 0 0 0 0 0 6 6 6 6 : : : : 0 0 0 0 0 0 0 0
2 2 2 2 : : : : 0 0 0 0 0 0 0 0 3 3 3 3 : : : : 0 0 0 0 0 0 0 0 4 4 4 4 : : : : 0 0 0 0 0 0 0 0 5 5 5 5 : : : : 0 0 0 0 0 0 0 0 6 6 6 6 : : : : 0 0 0 0 0 0 0 0
F
IELD SETTINGS
space
NOTE The default values mentioned in
on page 16
initial values shall be selected according to your
application. These values shall be confirmed by your
7 7 7 7 : : : : 0 0 0 0 0 0 0 0 ~
installer.
2 2 2 2 3 3 3 3 : : : : 5 5 5 5 9 9 9 9
CAUTION
The field settings [2] depends on the relevant local and
national regulations.
The field settings [9] depends on the application.
Before changing these settings, the new values shall be
confirmed by the installer and/or shall be according to the
local and national regulations.
The indoor unit shall be configured by the installer to match the
installation environment (outdoor climate, installed options, etc.) and
user demand. However, the field settings mentioned in
table" on page 16
a number of so called field settings are available. These field settings
are accessible and programmable through the user interface on the
indoor unit.
Each field setting is assigned a 3-digit number or code, for example
Sun
[1-03], which is indicated on the user interface display. The first digit
[1] indicates the 'first code' or field setting group. The second and
third digit [03] together indicate the 'second code'.
—
A list of all field settings and default values is given under
settings table" on page
7 7 7 7 : : : : 0 0 0 0 0 0 0 0 ~
columns to register the date and value of altered field settings at
2 2 2 2 3 3 3 3 : : : : 5 5 5 5 9 9 9 9
variance with the default value.
A detailed description of each field setting is given under
description" on page

Procedure

To change one or more field settings, proceed as follows.
7 7 7 7 : : : : 0 0 0 0 0 0 0 0 ~
2 2 2 2 3 3 3 3 : : : : 5 5 5 5 9 9 9 9
3
2
Press the z button for a minimum of 5 seconds to enter FIELD
1
SET MODE.
The $ icon (3) will be displayed. The current selected field
setting code is indicated ; (2), with the set value displayed to
the right - (1).
Press the bgi button to select the appropriate field
2
setting first code.
Press the bgj button to select the appropriate field
3
setting second code.
Press the pfi button and pfj button to change
4
the set value of the select field setting.
5 Save the new value by pressing the pr button.
"Field settings table"
are the values from factory. The actual
can be modified to customer preferences. Thereto,
16. In this same list, we provided for 2
14.
Indoor unit for air to water heat pump system and options

"Field settings

"Field
"Detailed
1
EKHBH/XE008BA
4PW56302-1