Advertisement
Quick Links
MODELS CGL-01SW, CGL-01DW
CGL-21SW, CGL-21DW
CGL(LD)-21SW, CGL(LD)-21DW
CGL-23SW, CGL-23DW
CGL-43SW, CGL-43DW
CGL CONTROL PANELS
INSTALLATION AND SERVICE MANUAL
For Simplex and Duplex.
NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible
party who maintains the system.
Part # 23833A150 | © 2012 Pentair Pump Group, Inc. | 11/08/12
(2HP, 208V, 1PH)
(2HP, 230V, 1PH)
(2HP, 230V, 1PH)
(2HP, 208-230V, 3PH)
(2HP, 460V, 3PH)
Advertisement
Related Manuals for Pentair Myers CGL-01SW
Summary of Contents for Pentair Myers CGL-01SW
- Page 1 For Simplex and Duplex. NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible party who maintains the system. Part # 23833A150 | © 2012 Pentair Pump Group, Inc. | 11/08/12...
-
Page 2: Location And Mounting
LOCATION AND MOUNTING CALIFORNIA PROPOSITION 65 WARNING: OUTDOOR USE The control box may be mounted at the location of This product and related the pump and basin or may be mounted in a remote accessories contain chemicals known to the location. - Page 3 CONNECTING PUMPS AND FLOATS TO CONTROL BOX PUMP CORD should be connected to the terminal strip in the Run the wires from both pumps to the bottom of control box. See wiring diagram for the proper the control box by means of one of the methods terminal connections.
- Page 4 CHECKING PUMP CURRENT DRAW 1 PHASE PUMPS 3. If you get a reading of 0, make sure there is voltage to the motor leads. Push the overload 1. Use an amprobe to check the amperage of the reset button on the overload relay in the control pump.
- Page 5 TESTING COMPONENTS IN CONTROL BOX WARNING 3. With an ohmmeter on the R x 1 scale touch terminals X2 and X1 (secondary), you should get To prevent electrical shock, disconnect power entering a reading of approximately 3.6 ohms for Simplex the control box and turn the circuit breaker in the panels and 1.6 ohms for Duplex panels.
- Page 6 TESTING COMPONENTS IN CONTROL BOX should be on pin 3, and the “red” lead should be on and touch the other lead to the other capacitor pin 5. You should have a reading of approximately terminal. If the capacitor is good, the needle will go 920-1020 ohms.
-
Page 7: Troubleshooting Chart
TROUBLESHOOTING CHART (SIMPLEX PANELS) 23833A150 11/08/12... - Page 8 TROUBLESHOOTING CHART (DUPLEX PANELS) 23833A150 11/08/12...
- Page 9 PUMP CURRENT DRAW, WINDING RESISTANCE OVERLOAD HEATER SELECTION* RESISTANCE MODEL VOLTAGE PHASE F.L.A. L.R.A. BLK-WH BLK-RED WH-RED HEATER HEATER NO. WGL20-01 3450 15.0 52.5 1.14-1.26 4.63-5.11 5.77-6.37 — — WGL20-21 3450 12.5 44.0 1.46-1.62 7.20-8.00 8.66-9.62 — — WGL20-03 3450 34.0 2.65-2.93 2.65-2.93 2.65-2.93...
- Page 10 USE COPPER WIRE ONLY OVERLOAD PUSH IN TO RESET PUMP PUMP AUTO HAND LIGHT SEAL LEAK LIGHT GRD. 23833A150 11/08/12...
- Page 11 13-3/8 5/16 DIA. 15-5/16 14-5/8 15-1/2 7-23/32 ALARM LIGHT (22000A020 OR 22000A011) FLASHER (22002A001) END SECTION (21996A000) TERMINAL BLK. (21995A000) ENCLOSURE BACK PANEL CIRCUIT BREAKER (21981C106A) START RELAY (21981C110A) (21985A001) (21990A000) CAPACITOR BRACKET (2) (21989A002) USE COPPER WIRE ONLY U.L. LABEL MOUNTING BRACKET (21997B024) START CAPACITOR...
- Page 12 13-3/8 5/16 DIA. 15-5/16 14-5/8 15-1/2 7-23/32 ALARM LIGHT (22000A020 OR 22000A011) FLASHER (22002A001) END SECTION (21996A000) TERMINAL BLK. (21995A000) ENCLOSURE BACK PANEL CIRCUIT BREAKER (21981C106A) START RELAY (21981C110A) (21985A001) (21990A000) CAPACITOR BRACKET (2) (21989A002) USE COPPER WIRE ONLY U.L. LABEL MOUNTING BRACKET (21997B024) START CAPACITOR...
- Page 13 15-27/64 5/16 DIA. 17-7/16 16-3/4 17-1/2 7-11/16 ALARM LIGHT (22000A020 OR 22000A011) FLASHER (22002A001) BACK PANEL (21981C111A) CIRCUIT BREAKER MOUNTING BRACKET ENCLOSURE (21985A003) (21997B022) (21981C107A) U.L. LABEL TOGGLE SWITCH (21979A003) LIGHT ASSEMBLY (21973A002) PUMP PUMP AUTO LIGHT BULB (2) HAND LIGHT (21974A001) LIGHT ASSEMBLY...
- Page 14 15-27/64 5/16 DIA. 17-7/16 16-3/4 17-1/2 7-11/16 ALARM LIGHT (22000A020 OR 22000A011) FLASHER (22002A001) BACK PANEL (21981C111A) CIRCUIT BREAKER ENCLOSURE (22362A001) (21981C107A) MOUNTING BRACKET (21997B022) U.L. LABEL TOGGLE SWITCH (21979A003) LIGHT ASSEMBLY (21973A002) PUMP PUMP AUTO LIGHT BULB (2) HAND LIGHT (21974A001) LIGHT ASSEMBLY...
- Page 15 17-31/64 5/16 DIA. 19-31/64 18-7/8 19-5/8 10-5/8 ALARM LIGHT (22000A020 OR 22000A011) FLASHER (22002A001) CIRCUIT BREAKER (2) BACK PANEL (21985A001) (21981C112A) ENCLOSURE END SECTION (21981C108A) (21996A000) START RELY (2) TERMINAL BLK. (21990A002) (21995A000) CAPACITOR BRACKET (2) (16754A003) USE COPPER WIRE ONLY U.L.
- Page 16 17-31/64 5/16 DIA. 19-31/64 18-7/8 19-5/8 10-5/8 ALARM LIGHT (22000A020 OR 22000A011) FLASHER (22002A001) CIRCUIT BREAKER (2) BACK PANEL (21985A001) (21981C112A) ENCLOSURE END SECTION (21981C108A) (21996A000) START RELY (2) TERMINAL BLK. (21990A002) (21995A000) USE COPPER WIRE ONLY U.L. LABEL CAPACITOR BRKT (4) (16754A002) START CAPACITOR (2) (12141A005)
- Page 17 17-31/64 5/16 DIA. 19-31/64 18-7/8 19-5/8 10-5/8 ALARM LIGHT (22000A020 OR 22000A011) FLASHER (22002A001) CIRCUIT BREAKER (2) BACK PANEL (21985A001) (21981C112A) ENCLOSURE END SECTION (21981C108A) (21996A000) START RELY (2) TERMINAL BLK. (21990A000) (21995A000) USE COPPER WIRE ONLY U.L. LABEL CAPACITOR BRKT. (4) (16754A002) START CAPACITOR (2) (12141A005)
- Page 18 17-31/64 5/16 DIA. 19-31/64 18-7/8 19-5/8 10-5/8 ALARM LIGHT (22000A020 OR 22000A011) FLASHER (22002A001) ENCLOSURE (21981C108A) BACK PANEL MOUNTING BRKT. CIRCUIT BREAKER (2) (21981C112A) (21997C027) (21985A003) USE COPPER WIRE ONLY PUMP 1 PUMP 2 AUTO AUTO U.L. LABEL TOGGLE SWITCH (2) (21979A003) HAND HAND...
- Page 19 17-31/64 5/16 DIA. 19-31/64 18-7/8 19-5/8 10-5/8 ALARM LIGHT (22000A020 OR 22000A011) FLASHER (22002A001) ENCLOSURE (21981C108A) BACK PANEL MOUNTING BRKT. CIRCUIT BREAKER (2) (21981C112A) (21997C027) (22362A001) USE COPPER WIRE ONLY PUMP 1 PUMP 2 AUTO AUTO U.L. LABEL TOGGLE SWITCH (2) (21979A003) HAND HAND...
- Page 20 START MAIN START MAIN 23833A150 11/08/12...
- Page 21 START MAIN 23833A150 11/08/12...
- Page 22 START MAIN MAIN START START MAIN MAIN START 23833A150 11/08/12...
- Page 23 START MAIN MAIN START 23833A150 11/08/12...
-
Page 24: Standard Limited Warranty
Warranty is effective only if Pentair Myers authorized control panels are used. All seal fail and heat sensing devices must be hooked up, functional and monitored or this warranty will be void. Pentair Myers will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Myers be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Myers service facility.