Related Manuals for Pentair ICHNDHLD
Summary of Contents for Pentair ICHNDHLD
-
Page 1: Installation Guide
INTELLICENTER WIRELESS CONTROL SYSTEM ™ WIRELESS CONTROL PANEL INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS... -
Page 2: Table Of Contents
Contents Warning and Safety Instructions iii-vi IntelliCenter Control System Wireless Control Panel Charging the IntelliCenter Wireless Control Panel Home Screen Battery Icon Wireless Control Panel Transceiver Installation IntelliCenter Control System Wireless Controller kit Mounting the Wireless Transceiver Connecting the Transceiver to the IntelliCenter Control System Load Center Home Screen Transceiver Connected to the IntelliCenter... -
Page 3: Warning And Safety Instructions
This guide provides installation and operation instructions for the IntellliCenter Control System Wireless Control ™ Panel. Consult Pentair Water Pool and Spa, Inc. with any questions regarding this equipment (see “Customer Service/Technical Support”, page ii). Attention Installer: This guide contains important information about the installation, operation and safe usage of this product. - Page 4 CAUTION: IMPORTANT BATTERY INFORMATION • Danger of explosion if battery is incorrectly replaced. • ONLY USE a Pentair Water Pool and Spa (“Pentair”) replacement battery. Order Battery (P/N 522054). • Rechargeable Lithium-ion battery disposal: Unwanted lithium ion battery pack may be returned to your local recycling center or the manufacturer for disposal.
- Page 5 Afin de satisfaire aux exigences de la FCC/IC l’exposition RF, une distance de séparation minimale de 8 po (20 cm) doit être maintenue entre l’équipement et toutes les personnes en fonctionnement normal. Notice for Wireless Remote Control (FCC ID: P4H-ICHNDHLD & IC: 4249A-ICHNDHLD): This portable transmitter with its antenna has shown compliance with FCC/IC SAR limits for general population / uncontrolled exposure.
- Page 6 IMPORTANT WARNING AND SAFETY INSTRUCTIONS General Installation Information 1. All work must be performed by a licensed electrician, and must conform to all national, state, and local codes. 2. Install to provide drainage of compartment for electrical components. 3. If this system is used to control underwater lighting fixtures, a ground-fault interrupter (GFCI) must be provided for these fixtures.
-
Page 7: Intellicenter Control System Wireless Control Panel
Canadian installations require a minimum of (3) meters from pool water. Do not recharge outdoors. Only use Pentair approved AC power adapter transformer. The IntelliCenter Wireless Control Panel is water resistant and can be exposed to temporary splashing or wet hands. -
Page 8: Charging The Intellicenter Wireless Control Panel
Charging the IntelliCenter Wireless Control Panel When you are not using the IntelliCenter Wireless Control Panel, place it in the cradle to recharge the battery. This allows the battery to be fully charged at all times. To charge the Wireless Control Panel battery •... -
Page 9: Home Screen Battery Icon
When the battery is fully charged the left to right scrolling of the battery icon will stop. The battery icon will be solid when the battery is fully charged. Note: If the battery requires replacement, only use Pentair replacement battery (P/N 522054). Battery Icon Air Temp 65°... -
Page 10: Wireless Control Panel Transceiver Installation
Wireless Control Panel Transceiver Installation The following procedure describes how to install the IntelliCenter Control System Wireless Controller transceiver module and connect the Transceiver cable to the COM port on the IntelliCenter Control System main circuit board. Note: IF YOU ARE USING MULTIPLE WIRELESS CONTROLLER: IntelliCenter Control System Wireless Controller, be sure the Transceiver for each of these controllers are located at least 6 ft. - Page 11 Mounting the Transceiver (Continued) 6. Position the back plate over the mounting points and secure it with the four mounting screws (provided in the kit). 7. Carefully slide the transceiver circuit board into the back plate. 8. Strip the leads of the communication cable wires back ¼ in. Insert the wires into the connector screw terminals (provided in the kit).
-
Page 12: Connecting The Transceiver To The Intellicenter Control System Load Center
Connecting the Transceiver to the IntelliCenter™ Control System Load Center SWITCH OFF AC POWER TO THE INTELLICENTER CONTROL SYSTEM LOAD CENTER BEFORE MAKING ANY CONNECTIONS. To connect the Transceiver wires to the COM port on the system circuit board: BEFORE REMOVING THE HIGH VOLTAGE COVER PANEL FROM THE LOAD CENTER OR POWER CENTER ENCLOSURE SWITCH OFF THE POWER AT THE HOUSE MAIN CIRCUIT BREAKER BOX. - Page 13 Connecting the Transceiver to the IntelliCenter™ Control System Load Center (Continued) 5. Strip the leads of the communication cable wires back ¼ in. Insert the wires into the connector screw terminals (provided in the kit). Using a small flat-blade screwdriver, secure the wires with the COM PORT terminal screws.
-
Page 14: Transceiver Connected To The Intellicenter Control System Load Center
Transceiver Connected to the IntelliCenter™ Control System Load Center Wireless Control Panel Transceiver RS-485 (COM Port) Transceiver connects to the IntelliCenter Control System IntelliCenter Control System RS-485 (COM Port) on the Load Center main circuit board (Located outside at equipment pad) IntelliCenter Control System Wireless Control Panel Installation Guide... -
Page 15: Intellicenter Control System Setup
IntelliCenter Control System Wireless Control Panel Setup The IntelliCenter Control System Wireless Control Panel requires optional Kit P/N 522036. This kit includes a wireless transceiver with antenna which connects to an RS-485 COM port on the Outdoor Control Panel circuit board located in the control system Load Center. For IntelliCenter Control System start up information, refer to the IntelliCenter™... - Page 16 Setup the Wireless Control Panel (Continued) 4. From the Select Wireless Channel screen you can choose a channel that has the best signal strength. Note (*): RSSI and LQI can vary widely. Human Select Wireless Channel movement and varying EMI (radio frequency interference) can have considerable effect on RSSI and LQI even for links between stationary nodes.
-
Page 17: Wireless Control Panel Firmware Update
Wireless Control Panel Firmware Update The IntelliCenter Control System Wireless Control Panel current firmware can be updated using the USB port. Updating the Current Wireless Control Panel Firmware 1. From the Home screen on the Wireless Control Panel. Tap Settings > Advanced System Configuration >... -
Page 18: Intellicenter Control System Menu Structure
General: (Location, Date & Time, Units, Features and Lights List Order, Backlight, Temperature Sensor Calibration, Day / Night Themes, Manual Operation Priority, Chemistry Readings Badge. Alerts and Notifications Security (Passcode Protect) Pentair User Portal Groups Advanced System Configuration: Installation Setup: Body Configuration,Circuits, Pumps, Heaters, Valves, Chemistry, Pool/Spa Cover. - Page 19 Notes IntellliCenter Control System Wireless Control Panel Installation Guide...
- Page 20 All Pentair trademarks and logos are owned by Pentair or by one of its global affiliated. IntelliCenter™ is a trademark of Pentair Water Pool and Spa, Inc. and/or its affiliated companies in the United States and/ or other countries. Unless expressly noted, names and brands of third parties that may be used in this document are not used to indicate an affiliation or endorsement between the owners of these names and brands and Pentair Water Pool and Spa, Inc.