Sony PCS-1 System Integration Manual page 22

Item
General setting Language setting/
Language
IR repeater mode
Camera control
reception
Memory Stick format
ISDN setting Country/region
Country/region number
Protocol
Trunk exchange
number/local number
Sub-address
Incoming setting Automatic incoming
Number of lines used
Restricted network
LAN band used
ISDN dial-in
Video system
Number of video frames
Audio system
Remote camera control
T.120 data
Audio setting Input switching
Microphone selection
Lip sync
Echo canceller
Beep Sound
Recording mute
Setting for Administrator password
administrator
Super-user password
Remote access
password
Web monitor
Storage of address book
Loading of address book
Setting of LAN DHCP mode
Host name
IP address
Network mask
Gateway address
DNS address
Gate keeper used
Gate keeper address
User name
1-18
Contents of setting
Select the language (English, French, German, Japanese, Spanish, Italian, or
Chinese) of the menu and message displayed on the screen.
Select the mode for putting the monitor into the standby state or turning on the
power when a Sony's monitor is used. Usually, set to "Mode 1".
Set to "on" when receiving the camera control command from the remote side.
Set to "Off" when not receiving it.
Execute the format of a Memory Stick.
Select the country and region in which a communication terminal is used. Set to
"Japan" when a communication terminal is used in Japan.
Set the country/region number. Set to "81" when a communication terminal is
used in Japan.
Select the protocol of the ISDN line used. Select "NTT" when an ISDN line is
used in Japan.
Set the connected ISDN line number. Be sure to set the ISDN number when a
bonding interface is used.
Enter it when a sub-address is registered
Select automatic incoming "On" and manual incoming "Off".
Select the number of ISDN lines used during incoming.
!B, 2B, 3B, 4B, 5B, 6B, 8B, or 12B channel can be selected.
Select the communication rate (Auto or 56 K) when connecting using an ISDN
line.
In a few countries (America, etc.) and regions, two types of rates (64 Kbps and 56
Kbps) are used.
Usually, select "Auto" as the communication rate of ISDN.
Set the bandwidth (1 to 1920) when communicating via LAN.
Set to "On" when using multiple subscriber numbers during connection using an
ISDN line. Set to "Off" when not using them.
Select a video coding system.
Select the maximum number of video transmission frames (15 fps or 30 fps).
Select an audio coding system.
Set to "On" when controlling the camera on the remote side. Set to "Off" when
not controlling it.
Set to "On" when making the data conference conforming to T.120 using
NetMeeting. Set to "Off" when not making it.
Select the audio input (MIC, AUX, or MIC + AUX).
Select the microphone used (internal, external, DSB MIC, or DSB AUX IN).
Set to "On" when using a lip sync function. Set to "Off" when not using it.
Set to "Internal" when using an internal echo canceller and set to "External" when
using an external echo canceller. Set to "Off" when not using an internal echo
canceller.
Set to "On" when generating a beep sound during reception of a remote controller
signal. Set to "Off" when not generating it.
Set to "On" when outputting a voice to the AUDIO OUT (MIXED) terminal. Set
to "Off" when not outputting it.
Set the password for an administrator. The administrator can operate a setting
menu and address book menu.
Set the password for a super-user. The super-user can operate an address book
menu.
Set the password when accessing from Web.
Select whether to permit the conference state monitoring function (the updating of
JPEG screen) from Web.
Save the data in an address book menu in "Memory Stick".
Load the data in an address book menu from "Memory Stick".
Set whether to use DHCP (Dynamic Host Configuration Protocol). Set to "Auto"
when automatically acquiring an IP address, net mask, gateway address, and DNS
address. Set to "Off" when not automatically acquiring it.
Set the host name of this unit.
Set the IP address of this unit.
Set the network mask of this unit.
Set a default gateway address.
Set a DNS (Domain Name System) server address.
Set to "On" when using a gate keeper and set to "Off" when not using it. Set to
"Auto" when automatically searching a gate keeper.
Set the IP address of a gate keeper.
Set the user name (H.323 alias) registered in a gate keeper.
Initial value
Japan/Japanese
MODE1
On
Japan
81
NTT
On
12B
Auto
1024 Kbps
Off
All capabilities
15 fps
All capabilities
On
Off
MIC
Internal
Off
Internal
On
On
On
Off
Blank
Blank
Blank
Blank
Blank
Off
Blank
Blank
PCS-1/PCS-1P