Sony DSR-DR1000A Operating Instructions Manual page 31

When controlling this unit from an editing control unit
connected to the REMOTE IN (R)connector, see "Control
mode selector" on page 11 and the description of the
REMOTE I/F menu item on page 69.
1
Power on the video monitor, then set its input
switches according to the signals input from the
player.
2
Set up the player to play back a tape.
For details, refer to the operating instructions for the
player.
3
Power on this unit by pressing the 1 switch on the
front panel.
4
When the REMOTE indicator is off (the external
editing control unit is not used), use the COUNTER
SELECT button to select the type of time data to be
used.
Each press of this button cycles through three options:
COUNTER (CNT value), TC (time code), and U-BIT
(user bit data). The time data type indicator for each
option lights as it is selected.
Selected time data
Count value of the time
counter
Time code
User bit data
When the REMOTE indicator is lit, selection of the
time data type is carried out at the editing control unit.
5
Select the formats of video and audio input signal to
be recorded.
Use the INPUT SELECT buttons in the video/audio
input setting section to select the desired signal
formats. Each selection is shown by a lit indicator in
the INPUT signal display section.
Video input signal Corresponding
(input connector) INPUT
SELECT
button
Composite signal VIDEO
(VIDEO IN: Y/CPST)
Separated Y/C VIDEO
signal
(VIDEO IN: Y/CPST
and R−Y/S−C)
Component signal VIDEO
(VIDEO IN: Y/CPST,
R−Y/S−C, and B−Y/
S−Y)
Time data type indicator
COUNTER
TC
U-BIT
Lit indicator
in the INPUT
signal display
section
COMPOSITE
in VIDEO
group
S VIDEO in
VIDEO group
Y−R,B in
VIDEO group
Video input signal Corresponding
(input connector) INPUT
SELECT
button
SDI signal VIDEO
(SDI IN)
i.LINK-compatible VIDEO
digital video signal in
DV format
( S400(i.LINK))
Internal test video VIDEO
signal
Audio input signal Corresponding
(input connector) INPUT SELECT
button
Analog signal CH1 1/2 and
(AUDIO IN 1/3 and CH2 3/4
AUDIO IN 2/4)
AES/EBU signal CH1 1/2 and
(AUDIO (AES/EBU) CH2 3/4
IN)
SDI signal CH1 1/2 and
(SDI IN) CH2 3/4
i.LINK-compatible automatic
digital audio signal in setting
DV format depending on
video input
( S400(i.LINK))
signals
Internal test audio CH1 1/2 and
signal CH2 3/4
Caution
Once you have started recording, you cannot change
the input signal selection.
6
Select the audio mode.
Select either two-channel mode (2 CHANNEL) or
four-channel mode (4 CHANNEL) with the REC
MODE menu item (see page 68). The corresponding
indicator lights in the REC MODE display.
Audio mode Lit indicator in the REC MODE
display
2-channel mode 2CH
4-channel mode 4CH
Cautions
• Two audio recording modes, with either two
channels at 48 kHz or four channels at 32 kHz, can
be used on this unit. It is not possible to select any
other mode (for example with four channels at 48
kHz).
• If there is a point where the audio mode is switched,
it is not possible to carry out insert editing over a
section including that point.
Lit indicator
in the INPUT
signal display
section
SDI in VIDEO
group
i.LINK
SG in VIDEO
group
Lit indicator
in the INPUT
signal display
section
ANALOG in
AUDIO group
AES/EBU in
AUDIO group
SDI in AUDIO
group
i.LINK
SG in AUDIO
group
31
Recording