Audio Settings - JVC KD-R991BT Instruction Manual

AUDIO SETTINGS

For key layout on the faceplate, see page 3 or page 4.
1
Press and hold .
2
Perform 'select an item ( 3 or 4)' operation to select an item
(see the following table).
3 2
Repeat step until the desired item is selected/activated or follow
the instructions stated on the selected item.
4
Press to exit.
To return to the previous setting item, press
EQ SETTING
PRESET EQ Select a preset equalizer suitable to the music genre.
• Select [USER] to use the settings made in [EASY EQ] or [PRO EQ].
FLAT/DRVN 3/DRVN 2/DRVN 1/HARD ROCK/HIP HOP/JAZZ/POP/R&B/
USER/CLASSICAL
Drive equalizer (DRVN 3/DRVN 2/DRVN 1) boosts specific frequencies in
the audio signal to reduce the noise heard from outside the car or running
noise of the tyres
EASY EQ Adjust your own sound settings.
• The settings are stored to [USER].
• The settings made may affect the current settings of [PRO EQ].
SUB.W SP * 1 * 2
: 00 to +06
SUB.W * 1 * 3
: –50 to +10
BASS: LVL–09 to LVL+09
MID: LVL–09 to LVL+09
TRE: LVL–09 to LVL+09
PRO EQ Adjust your own sound settings.
• The settings are stored to [USER].
• The settings made may affect the current settings of [EASY EQ].
62.5HZ
LEVEL –09 to LEVEL +09 (LEVEL 00): Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
ON: Turns on the extended bass. ; OFF: Cancels.
100HZ/160HZ/250HZ/400HZ/630HZ/1KHZ/1.6KHZ/2.5KHZ/4KHZ/6.3KHZ/10KHZ/
16kHZ
.
LEVEL –09 to LEVEL +09 (LEVEL 00): Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
Default: XX
Q FACTOR
AUDIO CONTROL
BASS BOOST
LOUDNESS
SUB.W LEVEL *
(Default: +03
00
LVL 00
LVL 00
SUBWOOFER
LVL 00)
SET * 3
FADER
* 1 , * 2 , *
1.35/1.50/2.00: Adjust the quality factor.
LEVEL +01 to LEVEL +05: Selects your preferred bass boost level. ;
OFF: Cancels.
LEVEL 01/LEVEL 02: Boosts low or high frequencies to produce a well-
balanced sound at low volume. ; OFF: Cancels.
1 SPK-OUT * 2
(Not applicable when 3-way crossover is selected.)
SUB.W 00 to SUB.W +06 (SUB.W +03): Adjusts the
output level of the subwoofer connected via speaker
lead. ( 38)
PRE-OUT *
3
SUB.W –50 to SUB.W +10 (SUB.W 00): Adjusts
the output level of the subwoofer connected to the
lineout terminals (SW or REAR/SW) through an external
amplifier. ( 39)
ON: Turns on the subwoofer output. ; OFF: Cancels.
(Not applicable when 3-way crossover is selected.)
POSITION R15 to POSITION F15 (POSITION 00): Adjusts the front and
rear speaker output balance.
3
: ( 24)
23
ENGLISH