Canon imageCLASS MF8350Cdn Starter Manual page 26

(If you use the machine for a long time or to perform a large amount of printing
in a poorly ventilated room, the ozone or other odors generated by the machine
may create an uncomfortable working environment. In addition, chemical
particles are dispersed during printing; therefore, it is important to provide
adequate ventilation.)
• A location near equipment that generates magnetic or electromagnetic waves
• A laboratory or location where chemical reactions occur
• A location exposed to salt air, corrosive gases, or toxic gases
• A location, such as on a carpet or mat, that may warp from the weight of the
machine or where the machine is liable to sink
Installation Space
Required installation space
Front View
1327
Paper
Feeder cover
cassette
100
Rear cover
Maintenance and Inspections
IMPORTANT
• Follow the instructions in the caution label attached to this machine.
• Avoid shaking or applying a shock to this machine.
• To prevent the paper jam, do not turn the power ON/OFF, open/close the
operation panel or rear cover, and load/unload paper in the middle of printing
operation.
• Be sure to remove the toner cartridge from the machine when transporting the
machine.
• To avoid exposing the toner cartridge to light, place it in the protective bag
included with this machine or wrap it in a thick cloth.
• Clean this machine regularly. If this machine becomes dusty, it may operate
improperly.
• Use a modular cable of 3 m or shorter in length.
• Depending on your locale or your telephone connection, you may be unable to
perform data communication. In this case, contact your local authorized Canon
dealer or the Canon help line.
• The repairing parts and toner cartridges for the machine will be available
for at least seven (7) years after production of this machine model has been
discontinued.
Contacting Service Center
When you have a problem with your machine and you cannot solve it, even if you
refer to the manuals or online help, please contact your local authorized Canon
dealer from whom you purchased the equipment (if under warranty), or with whom
you have a servicing contact.
Legal Notices
Model Name
MF8350Cdn (F157902)
EMC requirements of EC Directive
This equipment conforms with the essential EMC requirements of EC Directive. We
declare that this product conforms with the EMC requirements of EC Directive at
nominal mains input 230 V, 50 Hz although the rated input of the product is 220 to
240 V, 50/60 Hz. Use of shielded cable is necessary to comply with the technical EMC
requirements of EC Directive.
20
Feeder
100
International ENERGY STAR Program
As an ENERGY STAR® Partner, Canon Inc. has determined that
this product meets the ENERGY STAR Program for energy
efficiency.
The International ENERGY STAR Office Equipment Program is an
international program that promotes energy saving through the
use of computers and other office equipment.
The program backs the development and dissemination
of products with functions that effectively reduce energy
consumption. It is an open system in which business proprietors
can participate voluntarily.
The targeted products are office equipment, such as computers,
displays, printers, facsimiles, and copiers. The standards and
(mm)
logos are uniform among participating nations.
IPv6 Ready Logo
The machine uses the operating system which obtained IPv6
Ready Logo Phase-1 defined by IPv6 Forum.
Laser Safety Information
Laser radiation could be hazardous to the human body. For this reason, laser
radiation emitted inside this equipment is hermetically sealed within the protective
housing and external cover. No radiation can leak from the machine in the normal
operation of the product by the user.
This machine is classified as a Class 1 Laser Product under IEC 60825-1: 2007,
EN60825-1: 2007.
220 to 240 V Model
The label shown below is attached to the laser scan unit on the machine.
This machine has been classified under IEC 60825-1: 2007, EN60825-1: 2007 and
conforms to the following classes:
CLASS 1 LASER PRODUCT
LASER KLASSE 1
APPAREIL À LASER DE CLASSE 1
APPARECCHIO LASER DI CLASSE 1
PRODUCTO LÁSER DE CLASE 1
APARELHO A LASER DE CLASSE 1
LUOKAN 1 LASER-TUOTE
LASERPRODUKT KLASS 1
CAUTION
Use of controls, adjustments, or performance of procedures other than those
specified in the manuals for the machine may result in hazardous radiation exposure.
Users in New Zealand
This equipment does not fully meet Telecom's impedance requirements.
Performance limitations may occur when used in conjunction with some parts of
the network. Telecom will accept no responsibility should difficulties arise in such
circumstances.
Trademarks
Canon, the Canon logo, and imageCLASS are trademarks of Canon Inc.
Microsoft, Windows and Windows Vista are either trademarks or registered
trademarks of Microsoft Corporation in the United States and/or other countries.
All other product and brand names are registered trademarks, trademarks or service
marks of their respective owners.