1. Manuals
  2. Brands
  3. ActionTec Manuals
  4. Modem
  5. DataLink V.90 PC Card Fax Modem PCMCIA
  6. User manual

ActionTec DataLink V.90 PC Card Fax Modem PCMCIA User Manual

Pc card fax modem
Hide thumbs Also See for DataLink V.90 PC Card Fax Modem PCMCIA:
Table of Contents

Advertisement

Quick Links

Download this manual
DataLink V.90
PC Card

Fax Modem

User Guide

Advertisement

Table of Contents
loading

Related Manuals for ActionTec DataLink V.90 PC Card Fax Modem PCMCIA

Summary of Contents for ActionTec DataLink V.90 PC Card Fax Modem PCMCIA

  • Page 1: Fax Modem

    DataLink V.90 PC Card Fax Modem User Guide...

  • Page 2: Table Of Contents

    Table of Contents Introduction Package Contents System Requirements Technical Support Before You Begin DOS and Windows 3.1x Windows 95 and 98 Windows NT 4.0 Installing the Modem Installing the Driver Software Windows 95 Windows 98 Windows Me Windows NT 4.0 Windows 2000 Windows XP Installing the...
  • Page 3 Table of Contents...

  • Page 4: Introduction

    Introduction Thank you for purchasing the Actiontec DataLink V.90 PCMCIA Fax Modem. The Modem offers notebook computer users the mobility and connectivity op- tions only a PCMCIA modem can deliver. Its small size and weight are a perfect match for the latest notebook computers. The Modem supports both the K56flex and ITU-T V.90 standards for connecting to the largest number of Internet Service Providers.

  • Page 5: Technical Support

    Technical Support Actiontec Electronics prides itself on making durable, high-quality, high-performance products. If you need assistance, the Actiontec Technical Support Department is available every day from 6 A.M. to 11 P.M. (MST) to provide professional support. Web site: www.actiontec.com/support 1 Introduction Actiontec Electronics, Inc.

  • Page 6: Before You Begin

    Before You Begin Before connecting the Modem, select the operating system used and read the pre-installation information. DOS and Windows 3.1x Most portable computers include some form of Card and Socket Services. This software enables the computer’s internal PCMCIA controller to operate. If Card and Socket Services are installed, Windows 3.1 and Windows for Workgroups 3.11 do not require any special drivers to communicate with the Modem;...
  • Page 7 3. To run Point Enabler, enter the following at the DOS prompt: and then press the Enter key on the keyboard. In the entry above, x specifies the COM port number (1-4) and y specifies the Interrupt (IRQ) used (1-15). Using 3 for the COM port and 9 for the IRQ works in most computers.

  • Page 8: Windows 95 And 98

    DataLink V.90 PCMCIA Fax Modem Windows 95 and 98 If the Modem is the first PC Card purchased for the notebook computer, ensure the computer’s PCMCIA controller has been initialized and properly configured for Windows 95 and 98 by following these instructions: 1.

  • Page 9: Windows Nt 4.0

    Windows NT 4.0 To ensure the computer is configured to use the Modem, the PCMCIA and COM 2 settings must be properly configured. PCMCIA Settings 1. After booting up the computer, select Start, Settings, then Control Panel. 2. In the “Control Panel” window, double-click Devices. 3.
  • Page 10 DataLink V.90 PCMCIA Fax Modem COM 2 Settings To ensure COM 2 (the preferred COM port for a Windows NT 4.0 installation) is available for the Modem to use, Actiontec recommends disabling COM 2 throughout the System BIOS Setup routine. To do this: 1.
  • Page 11 2 Before You Begin...

  • Page 12: Installing The Modem

    Installing the Modem The Modem is a Type II PCMCIA card and installs in a Type II or Type III 68-pin PCMCIA slot. Notebook computers usually have PC Card slots located on the side of the computer. To install the Modem, slide it gently into the slot, with the label facing up. Press firmly until the Modem is seated completely in the slot.

  • Page 13: Installing The Modem

    The Modem comes with its own dedicated phone cable. This cable has a standard RJ-11 connector on one end for the phone line, and a special connector that fits into the Modem on the other end. Insert the cable into the Modem, as shown in the figure, below.

  • Page 14: Installing The Driver Software

    Installing the Driver Software After installing the Modem, the drivers software must be loaded onto the computer. Select the operating system used, then follow the instructions. Windows 95 There are two version of Windows 95: 95a and 95 OSR2. To discover which version is running on the computer, select Start, Settings, Control Panel, then double-click System.
  • Page 15 4 Installing the Driver Software 4. The “Install From Disk” window appears. Insert the DataLink Installation CD in the CD-ROM drive of the computer, then click OK. 5. If Windows asks for an installation disk, click OK and enter the drive letter of the CD-ROM drive in the “Copy manufacturer’s files from”...
  • Page 16 DataLink V.90 PCMCIA Fax Modem Windows 95 OSR2 To load the Modem’s software drivers onto a computer running Windows 95 OSR2: 1. Turn on the computer. 2. Insert the Modem into the computer’s PCMCIA slot. 3. Windows detects the Modem, and the first “Update Device Driver Wizard” window appears.
  • Page 17 4 Installing the Driver Software 6. To determine which COM port and IRQ are assigned to the Modem, select Start, Settings, Control Panel, Modems, then Diagnostics. Click COM Port, then More Info to view the Modem’s properties. Next, go to chapter 5, “Installing the Communications Software.”...

  • Page 18: Windows 98

    DataLink V.90 PCMCIA Fax Modem Windows 98 To load the Modem’s software drivers onto a computer running Windows 98: 1. Turn on the computer. 2. Insert the DataLink Installation CD into the computer’s CD-ROM drive. 3. Insert the Modem into the computer’s PCMCIA slot. 4.
  • Page 19 4 Installing the Driver Software 5. When the next “Add New Hardware Wizard” window appears, select Search for the best driver for your device (Recommended), then click Next. 6. In the next window, click the CD-ROM drive check box, then click Next. 7.
  • Page 20 DataLink V.90 PCMCIA Fax Modem Alternate Windows 98 Installation 1. If Windows does not find the Modem’s driver software on the CD (see step 7 in the previous procedure), abort the process by clicking Back until the following window appears, select Display a list of all the drivers in a specific location…...
  • Page 21 4 Installing the Driver Software 3. When the “Install From Disk” window appears, ensure the DataLink Installation CD is inserted in the computer’s CD-ROM drive. Verify that the drive letter of the CD-ROM drive appears in the “Copy manufacturer’s files from” list box, then click OK. 4.

  • Page 22: Windows Me

    DataLink V.90 PCMCIA Fax Modem Windows Me To load the Modem’s software drivers onto a computer running Windows Me: 1. Turn on the computer. 2. Insert the DataLink Installation CD into the computer’s CD-ROM drive. 3. Insert the Modem into the computer’s PCMCIA slot. 4.

  • Page 23: Windows Nt 4.0

    4 Installing the Driver Software 6. When the final “Add New Hardware Wizard” window appears, click Finish. The driver software is loaded. Next, go to chapter 5, “Installing the Communications Software.” Windows NT 4.0 Before beginning this installation, ensure that the COM 2 port has been disabled in the system BIOS, and that the PCMCIA is set to “boot”...
  • Page 24 DataLink V.90 PCMCIA Fax Modem 4. When the “Modem Properties” window appears, click Add. 5. The “Install New Modem” window appears. Ensure the check box is not checked, then click Next.
  • Page 25 4 Installing the Driver Software 6. In the next “Install New Modem” window, Windows detects the Modem as a “Standard Modem.” Click Change. 7. Insert the DataLink Installation CD in the computer’s CD-ROM drive, then click Have Disk. 8. In the next window, when prompted for the path to the files, enter the drive letter of the CD-ROM drive, then click OK.

  • Page 26: Windows 2000

    DataLink V.90 PCMCIA Fax Modem 9. When prompted to select the the manufacturer and model of the Modem, click OK, then Next in the following window. The driver software is installed.  Note: To verify Windows has found the Modem, select Start, Settings, Control Panel, then Modems.
  • Page 27 4 Installing the Driver Software 7. Double-click Standard PCMCIA Card Modem 8. The “Standard PCMCIA Card Modem Properties” window appears. Select Driver, then click Update Driver.
  • Page 28 DataLink V.90 PCMCIA Fax Modem 9. The first “Upgrade Device Driver Wizard” window appears. Click Next. 10. In the next “Upgrade Device Driver Wizard” window, select Search for a suitable driver for my device (recommended), then click Next.
  • Page 29 4 Installing the Driver Software 11. When the next window appears, select Specify a location, then click Next. 12. When the next window appears, insert the DataLink Installation CD in the CD-ROM drive of the computer. 13. Enter X:\Drivers\WindXP2k in the “Copy manufacturer’s files from” text box, where X is the drive letter of the CD-ROM drive.
  • Page 30 DataLink V.90 PCMCIA Fax Modem 14. In the next window, click Next. 15. The “Digital Signature Not Found” window appears. Read the warning, then click Yes.
  • Page 31 4 Installing the Driver Software 16. The last “Upgrade Device Driver Wizard” window appears. Click Finish. The driver software is installed.  Note: To verify the driver software installed correctly, return to the Device Manager and locate “Actiontec 56k PCMCIA Fax Modem.” Double-click the icon, and in the Driver tab, view the driver information.

  • Page 32: Windows Xp

    DataLink V.90 PCMCIA Fax Modem Windows XP To load the Modem’s software drivers onto a computer running Windows XP: 1. Insert the Modem into the computer’s PCMCIA slot. 2. Turn on the computer and while it boots up, insert the DataLink Installa- tion CD in the computer’s CD-ROM drive.
  • Page 33 4 Installing the Driver Software 4. The driver software installs. When the last “Found New Hardware Wizard” window appears, click Finish. The driver software is installed. Next, go to chapter 5, “Installing the Communications Software.”...

  • Page 34: Installing The Communcations Software

    Installing the Communcations Software If the Modem came with a communications software package, Actiontec recom- mends using this software for the Modem. The default installation parameters of the software are specially configured to work with the Modem, and supports both data and fax modes. To install the communications software on your computer: 1.
  • Page 35 5 Installing the Communcations Software...

  • Page 36: Troubleshooting

    Troubleshooting This section lists some common problems that may occur while using the Modem, and offers suggestions to solve them. Uninstalling the Modem Before attempting any troubleshooting, ensure the pre-installation procedure outlined in chapter 2, “Before You Begin,” was performed. If the Modem was in- stalled without following the pre-installation procedure, follow these instructions (for Windows 95 and 98 only): 1.
  • Page 37 2. Select Device Manager, then click on the plus sign (+) next to “PCMCIA.” 3. Click on the icon to highlight, then click Remove. 4. Exit Device Manager and restart Windows. 5. After booting up, Windows should detect new hardware for the PCMCIA Socket (if not, select Start, Settings, Control Panel, then double-click PC Card).
  • Page 38 DataLink V.90 PCMCIA Fax Modem will work with programs that access COM ports). To solve this problem, first ascertain which version of Windows 95 is running on the computer (see the “Window 95” section of chapter 4, “Installing the Driver Software,” for more details).
  • Page 39 Windows 95 OSR2 1. Eject the Modem from the computer 2. Select Start, Settings, Control Panel, then double-click Modems. 3. Click Modem once to highlight, then click Remove. 4. Close the “Control Panel” window and return to the Desktop. Do not reboot or restart the computer! Select Start, Programs, then MS-DOS Prompt! 5.

  • Page 40: Limited Warranty

    Limited Warranty Hardware: Actiontec Electronics, Inc., warrants to the end user (“Customer”) that this hardware product will be free from defects in workmanship and materials, under normal use and service, for twelve (12) months from the date of purchase from Actiontec Electronics or its authorized reseller. Actiontec Electronics’...
  • Page 41 Limited Warranty will make reasonable efforts to provide compatibility, except where the non-com- patibility is caused by a “bug” or defect in the third party’s product or from use of the software product not in accordance with Actiontec Electronics published specifications or user guide.
  • Page 42 DataLink V.90 PCMCIA Fax Modem WARRANTIES EXCLUSIVE: IF AN ACTIONTEC ELECTRONICS’ PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY FOR BREACH OF THAT WARRANTY SHALL BE REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT ACTIONTEC ELECTRONICS’ OPTION. TO THE FULL EXTENT ALLOWED BY LAW, THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, TERMS OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY...
  • Page 43 Limited Warranty Disclaimer: Some countries, states or provinces do not allow the exclusion or limita- tion of implied warranties or the limitation of incidental or consequential damages for certain products supplied to consumers, or the limitation of liability for personal injury, so the above limitations and exclusions may be limited in their application to you.

Table of Contents