Advertisement
Available languages
Available languages
Dry ironing
• Do not press the steam control button under the iron handle.
Vertical steam ironing
Recommendations: for
fabrics other than linen or
cotton, hold the iron a few
centimetres from the garment
to avoid burning the fabric.
Refilling the tank during use
• When the red «Tank empty» light is flashing
• Unplug the steam generator. Open the water tank filler
• Use a jug and fill it with water, then fill the tank, taking care not to exceed the «Max» level of the tank.
• Close the water tank filler
cover.
• Plug the steam generator in again. Press the «ON-OFF» restart button
ironing.
Power Zone Function
• Your appliance includes the Power Zone function: concentrated steam shot at the tip of the soleplate, to be used in
particular to target stubborn creases, detailing and zones that are difficult to access.
• To use this function, press the Power Zone button on top of the iron as often as necessary
Maintenance and cleaning
Cleaning your steam generator
• Do not use any type of cleaning or descaling product to clean the soleplate or the base unit.
• Never hold the iron or the base unit under a running tap.
• Cleaning the soleplate: we recommend using a soft damp cloth on the soleplate while it is
still warm to avoid damaging the coating.
• Your steam iron is fitted with an Autoclean soleplate, its exclusive active coating allows it to
eliminate any impurities that may be regularly generated during normal conditions of use.
Ironing with an unsuitable programme could nonetheless leave traces that require manual
cleaning.
• We recommend always standing your iron upright or on the iron rest to protect its coating.
• Clean the plastic parts from time to time using a slightly damp soft cloth.
Easy descaling of your steam generator
To extend the life of your steam generator and avoid scale on your ironing, your steam
Do not use any
generator is equipped with a built-in scale collector. This collector, located in the tank,
descaling substances
(industrial descaling
automatically removes the scale that forms inside.
products etc..) when
rinsing the «Anti-Calc»
Operation:
collector or the boiler
tank, they could
• An orange «Anti-Calc collector» light located on the control panel starts flashing to tell you
damage it.
that the Anti-Calc collector needs rinsing
Before emptying your
steam generator, it
must always be left
to cool for 2 hours
to avoid any risks of
been unplugged for at least two hours and has cooled down completely. To carry out
scalding.
this operation, the steam generator must be close to a sink as water may come out of
the tank when it is opened.
• Once the steam generator has cooled completely unscrew the scale collector
• Fully unscrew the collector
the tank.
• To clean the collector, simply rinse it under running water to remove any scale it contains
• You can soak the collector rod in white vinegar or lemon juice for a few hours to remove any stubborn scale stuck to
the rod.
• Hang the garment on a coat hanger and hold the fabric slightly taut with one hand.
• As steam is very hot: never attempt to remove creases from a garment while it is
being worn, always hang garments on a coat hanger.
• Holding the iron in a vertical position
on the steam control button (underneath the iron handle) moving the iron from top
to bottom
- fig.15.
- fig.4
, there is no more steam. The water tank is empty.
Important: This operation must not be carried out unless the steam generator has
- fig.18
and pull it out of the base unit
- fig.14
tilted slightly forwards, press repeatedly
cover.
- fig.8
under the control panel to continue
- fig.13.
- fig.17.
-
fig.19, it contains the scale that has built up in
10
- fig.6.
- fig.16.
Never use harsh or
abrasive cleaning
products.
Warning! The use of
abrasive pads will
damage the
soleplate coating- fig.26.
- fig.20.
• Pl
fi
• Fi
Nex
ligh
In a
app
• C
• Pl
• Re
• H
S
• Pl
• Fi
«A
• Fo
af
• O
• To
-
-
• Fo
g
Sto
• Pl
• Sw
• Ra
• St
• St
th
• Le
• If
st
• W
• Yo
i
Advertisement
