DSC Neo Power Series Installation Manual page 27

SIA Feature Programming Comments
Section
Exit Time Access to Entry and Exit delays and Bell Time Out for the system.
[005]>[001], option 3
Exit Delay Restart Opening a Delay zone door after it has already been opened and closed during an exit delay restarts the
exit delay timer.
[018], option 7
Auto Stay Arm on Un-vacated Function key: Forces the system to arm in Stay mode if the occupant does not exit the premises after
Premises pressing the Away function key.
[001]>[001]-[128] Zone type 05,
06,09
Exit Time and Progress System times and audible exit beeps can be disabled when using the wireless key to stay arm the system.
Annunciation/Disable or Remote When away arming, audible exit beeps can not be disabled.
Arming
[861]>[001]-[005], option 4
Entry delay(s) Access to entry and exit delays and bell time out for the system
[005]>[001]-[008], options 1 and 2 Note: Combined entry delay and communications delay (abort window) shall not exceed 60s.
Abort Window for Non-Fire zones Access to zone attributes, i.e., swinger shutdown, transmission delay and cross zone. May be disabled by
zone or zone type.
[002]>[001]-[128], option 7 ON
Abort Window Time - for Non- Access to the programmable delay before communicating alarms
Fire zones
Note: Combined entry delay and communications delay (abort window) shall not exceed 60 seconds.
[377]>[002], option 1
Abort Annunciation An audible tone is generated when an alarm is aborted during the abort window.
Duress Feature When this feature is enabled, selected user codes send a duress reporting code to the central station when
used to perform any function on the system. Section [019], option [6] must be enabled.
[*][5]> master code> user 2-95> 5>
2
Cancel Window Access to the communications cancel window. Minimum duration must be 5 minutes.
[377]>[002], option 6
Cancel Annunciation Access to the reporting code for Alarm Canceled.
[308]>[001], option 8
Cross Zoning Enables cross zoning for entire system. Zones can be enabled for cross zoning via zone attribute option
8 in sections [002][101] - [128].
[042]>Selection 3, option 002
Burglary Verification Timer Access to the programmable Cross Zone timer.
[005]>[000], option 3
Swinger Shutdown for Alarms Access to the swinger shutdown limit for zone alarms
[377]>[001], option 1 For all non-fire zones, shut down at 1 to 6 trips.
Swinger Shutdown Enable Access to swinger shutdown, transmission delay and cross zone attributes. Zone attribute option 6
(Swinger Shutdown enabled) is ON.
[002]>[001] - [128], option 6 ON
24-Hr. Auto-verified Fire Access to 24-Hr. Auto-verified Fire
[001]>[001]-[128], Zone type 025 Activates if Not restored within the specified time.
ON
Call Waiting Cancel Access to the dialing sequence used to disable call waiting. Call waiting string can be programmed in
[304]
[382], option 4 OFF
System Test: The system activates all keypad sounders, bells or sirens for 2 seconds and all keypad lights turn on.
Refer to user manual (part no. 29008365).
[*][6] Master Code, option 04
Walk Test Mode: This mode is used to test each zone on the system for proper functionality.
[*][8][Installer code][901]
Walk Test Communications Enables communication of zone alarms while walk test is active.
[382], option 2
Walk Test Start/ End Reporting Access to the reporting codes for walk test start and end times.
Codes
[308][401], options 1 and 2
PowerSeries Neo Installation Guide
- 27 -
Range/Default Requirement
Range:45- 255 Required
seconds
(programmable)
Default: 60 sec.
Default: Enabled Required
If no exit after full Required
arm
Default: Enabled
Default: Enabled Allowed
Range: 30 sec. to 4 Required
min.
(programmable)
Default: 30 sec.
Default: Enabled Required
Range: 00 - 45 sec. Required
Default: 30 sees (programmable)
Hard-coded ON Required
Default: N Required
Range: 005-255
Default: 005
A Cancel was Required
transmitted
Default: Enabled
Programming Required
required
Default: Disabled
Range: 000-255 sec. Allowed
Default: 60 seconds
Default: 2 trips Required
(programmable)
Non-police response Allowed
zones
Default: Enabled
Must choose zone Required
type for application
Depends on user Required
phone line
Default: Disabled
Default: Disabled