Table of Contents
Advertisement
John Lewis
Thank you for purchasing this Mixit wardrobe. Please read the instructions carefully before use to en-
sure safe and satisfactory operation of this product.
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Please check the pack contents before attempting to assemble this product.A full checklist of compo-
nents is given in this leaflet. If any components are missing, please contact your the John Lewis Helpline.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 90 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you are missing some fittings please contact our spare parts helpline on 0330 005 9435.
Opening hours are 9am - 5pm Monday to Friday.
Mixit wardrobe
Stock Code: 80319005 - 80319105 - 80319205
Spirit level
Screwdriver
0
0
20
30
40
0
Ruler/tape
Drill
Eye protection
measure
50
60
70
80
90
00
0
20
30
40
50
2
3
4
5
6
Small hammer
Page 1
MXT 01/13
Advertisement
Table of Contents
Related Manuals for John Lewis Mixit
Summary of Contents for John Lewis Mixit
- Page 1 Please check the pack contents before attempting to assemble this product.A full checklist of compo- nents is given in this leaflet. If any components are missing, please contact your the John Lewis Helpline. This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
- Page 2 Fittings checklist 30mm Metal dowel x 12 Cam lock x 12 Wooden dowel x 16 Wedge x housing x 4 Wedge x dowel x 4 Support foot x 4 Hanger rail support x 2 11mm Euroscrew x 4 15mm Screw x 2 Spacer x 2 Levelling Wedge x 2 Bumper x 4...
- Page 3 Parts checklist Page 3 MXT 01/13...
- Page 4 Step by step assembly instructions Step One ttach 4x wooden dowels (C) into the pre-drilled holes on top/bottom panels (1) as shown. Place the cam lock (B) into the holes on top/bottom panels (1) as shown, arrow pointing towards the bolt.
- Page 5 Step by step assembly instructions Step Four ttach 12x metal dowels ( ) into the pre-drilled holes on side panels (2) as shown. Use a screwdriver to turn fitting ( ) clockwise to fix. ttach 4x support foot (F) into pre-drilled holes on side panels (2) as shown. ttach 6x hinge mounting plate (U) into pre-drilled holes on side panels (2) as shown.
- Page 6 Step by step assembly instructions Step Five ttach top/bottom panels (1) and rails (5) (6) onto right side (2) as shown. Ensure metal dowels ( ) and wooden dowels (C) are aligned correctly with the holes of matching parts before attaching. Secure top/bottom panels (1) to right side panel (2) using a screwdriver to turn fitting (B) clockwise to fix.
- Page 7 Step by step assembly instructions Step Seven With help of an assistant, carefully rotate the unit. Step Eight Position back panel (4) as shown. Step Eight ttach back panel (4) onto back side of the unit using 30x nails (P), with the help of the nail guide (P1). Important: The cabinet MUST be ‘square’...
- Page 8 Step by step assembly instructions Step Nine With help of an assistant, carefully stand up the unit upright. Step Ten Use 2x levelling wedge (N) to level the unit. Page 8 MXT 01/13...
- Page 9 Step by step assembly instructions Step Eleven Fittings have been supplied in order to join units together. Place units together in their final positon. Decide position where to drill through using a Ø5 mm bit. Push the Connector (Q) into the hole and then screw Bolt (R) in from the other side, tighten with a screwdriver.
- Page 10 Step by step assembly instructions Step Twelve To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of two ‘L’ Brackets (M) fitted to the Top of the unit. Fix the Brackets (M) loosely onto the top of the unit using spacer (L) screw (I) and mark the wall for the wall fix- ing.
- Page 11 Step by step assembly instructions Step Thirteen Chose shelf (3) and hanging rail (S) position. Fix 2x hanger rail supports (G) onto the side panels (2) using the screws (H). Fit the hanging rail (S) on the rail supports (G) as shown. Fix 4x shelf support (E) onto the side panels (2).
- Page 12 Step by step assembly instructions Step Fourteen Fix 3x hinges (U) to each door using 15 mm screws (I). Repeat with all the doors. Step Fifteen Hang the clip hinge (T) to the hinge plate (U). Click them together. To remove the door push the clip hinge button and remove the door carefully. CLICK PUSH Page 12...
- Page 13 HINGE ADJUSTMENT INSTRUCTIONS LATERAL ADJUSTMENT by screw adjustment. FRONT-TO-BACK by slackening and re-tightening the hinge-arm mounting screw. VERTICAL ADJUSTMENT via slot on mounting plate by slackening and re-tightening the screws on mounting plate Page 13 MXT 01/13...
-
Page 14: Care And Maintenance
Wall fixing - if in doubt seek professional advice Wood Brick or Masonry Cavity wall If xing to wood Use an appropriate Special toggle make su re that it wall plug provided you wall plugs are isn't chipboard as are sure your wall is needed. -
Page 15: Safety Instructions
It must under no circumstances be used free-standing.No liability will be accepted for damage or injury caused by inadequate fixing or use without fixing. PLEASE KEEPTHESE INSTRUCTIONS FOR FUTURE REFERENCE John Lewis Partnership 171Victoria Street London SWIE 5NN www.johnlewis.com Page 15...